2019 Jeep Wrangler
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Jeep › Wrangler › 2019
These records cover every 2019 Jeep Wrangler. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
9 recalls name the 2019 Jeep Wrangler. Newest first.
Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear…
Risk and remedy
Risk
A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
Remedy
Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 77B.
Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
Risk and remedy
Risk
An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
Remedy
Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 30B.
Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Risk and remedy
Risk
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Remedy
Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1-800-853-1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V-028. Vehicles previously repaired under recall 21V-028 will need to have the new remedy completed.
Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Risk and remedy
Risk
Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Remedy
FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.
Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and Ram 2500, 2019-2020 Ram 1500 and 2020 Jeep Gladiator vehicles. In the event of a crash, a front seat belt retractor may not properly slow the occupant's forward movement after locking.
Risk and remedy
Risk
In the event of a crash, if the front seat belts fail to lock, there is an increased risk of injury.
Remedy
Chrysler will notify owners, and dealers will replace the front seat belt retractors, free of charge. The recall began November 12, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W67.
Chrysler (FCA US LLC) is recalling certain 2020 Jeep Gladiator and Jeep Cherokee, 2019-2020 Ram 1500 Pickup, Ram 2500 Pickup, Ram 3500 Pickup, Chrysler Pacifica, Dodge Durango, Jeep Grand Cherokee, Jeep Wrangler, and Jeep Renegade and 2019 Dodge Challenger vehicles equipped with 8.4" or 12" radio displays. A software error can cause the rearview camera…
Risk and remedy
Risk
The lingering rearview image can distract the driver, increasing the risk of a crash.
Remedy
Chrysler has notified owners, and dealers will update the radio display software, free of charge. Optionally, owners can choose to remotely update their software via an Over-The-Air (OTA) update available as of May 1, 2020. The recall began April 27, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W30-W37.
Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
Risk and remedy
Risk
The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W12.
Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and 2019 Ram 1500 vehicles. These vehicles have improperly machined steering column stub shafts that may break, possibly causing the steering wheel to detach from the steering column.
Risk and remedy
Risk
If the steering wheel detaches from the steering column, the driver may lose control of the vehicle, increasing the risk of crash.
Remedy
Chrysler will notify owners, and dealers will inspect the steering column, replacing it, as necessary, free of charge. The recall began April 5, 2019. Owners may contact FCA US customer service at 1-800-853-1403. Chrysler's number for this recall is V29.
Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.
Risk and remedy
Risk
An unexpected reduction in steering ability, can increase the risk of a crash.
Remedy
Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is UA5.
Owner complaints
747 complaints10 involved a crash11 involved a fire8 injuries
What owners report most
Latest complaints
- Electrical system
voltage regulator chip failure can cause the engine to stall or fail to start completely. Interior dashboard lights and dome lights along w/ windshield wipers going off without prompted happen after vehicle shutoff. Had to jump it to begin to start at times. Similar to recall U87.
- Unknown or other
Cluster panel failed. Dashboard is completely dark (ie. no speedometer, fuel guage. etc)
- Engine · Power train
On [XXX], my 2019 Jeep Wrangler Unlimited Rubicon (2.0L turbo) caught fire in the engine compartment while driving, at approximately 101,437 miles. The fire started near the turbocharger and heat shield area. There were no injuries, but the vehicle was moving on a public road with four occupants…
On [XXX], my 2019 Jeep Wrangler Unlimited Rubicon (2.0L turbo) caught fire in the engine compartment while driving, at approximately 101,437 miles. The fire started near the turbocharger and heat shield area. There were no injuries, but the vehicle was moving on a public road with four occupants, including two young children in car seats in the rear, when the fire started. The vehicle had been returned to me four days earlier, after approximately 2.5 months at Preferred Chrysler Dodge Jeep of Muskegon, MI for a timing chain replacement. After the fire, I found that the coolant reservoir hose had come off its fitting, and the hose barb appears to have been broken and the hose pushed back on. Several under-hood trim fasteners were also missing. My best assessment is that coolant sprayed onto the hot turbo/exhaust components and ignited. The vehicle has not been altered since the fire and is available for inspection at Watson's in Ludington, MI. I reported the fire to the manufacturer. They directed me to take it to the local dealer, then instructed the dealer not to inspect or work on it. The case was escalated internally, but as of 10/15/2026 no manufacturer inspection has occurred and no one has contacted me. The cause has not been confirmed by a dealer or independent shop. The fire occurred within the vehicle's Certified Pre-Owned warranty period. As of this filing, the manufacturer has not provided towing, rental, or any other assistance. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Electrical system
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 40 MPH, the instrument panel cluster suddenly went black. The contact pulled to the side of the road and waited for a family member to follow closely behind to ensure a safe drive, as essential driving…
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 40 MPH, the instrument panel cluster suddenly went black. The contact pulled to the side of the road and waited for a family member to follow closely behind to ensure a safe drive, as essential driving information was no longer visible. The vehicle was taken to the dealer, where it was diagnosed that the instrument panel cluster had failed and required a complete assembly replacement. The vehicle was pending repair. The contact learned of NHTSA Campaign Number: 24V652000 (Electrical System); however, the vehicle was not covered under the recall because the VIN was not included. The manufacturer was notified and confirmed that the VIN was not included in the recall. The failure mileage was approximately 81,000.
- Service brakes · Steering · Suspension
FCA US sent me a written warranty extension (15 years/150,000 miles) for the instrument panel cluster on my vehicle, covering a blank EVIC display with no digital speedometer, fuel level, temperature, odometer, or PRNDL. My vehicle has this condition intermittently. As I was traveling approximately…
FCA US sent me a written warranty extension (15 years/150,000 miles) for the instrument panel cluster on my vehicle, covering a blank EVIC display with no digital speedometer, fuel level, temperature, odometer, or PRNDL. My vehicle has this condition intermittently. As I was traveling approximately 55 mph my power steering, antilock brakes, speedometer, fuel gauge, traction control, all-wheel drive, and emergency brake warning lights came on/off. I actually lost power steering and was unable to turn the vehicle off. I reached out to Jeep and advised them of this and that I received the letter for the instrument panel cluster XZ1 and I thought this was related. I read the letter to them word for word, and they had the dealership perform the recall on my clutch. I didn't know until all of the same things happened again and I checked the receipt to confirm the work performed. I reached out to Jeep the same day and that was more than a week ago. I now have a new service transmission light. My vehicle is not safe to drive and they still don't even know why I called. My case number with Jeep is 98166358.
- Steering
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 45-50 MPH northbound on the Hutchinson River Parkway, the steering wheel failed to operate as needed. The vehicle was uncontrollable and started drifting towards the left before crashing into the highway…
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 45-50 MPH northbound on the Hutchinson River Parkway, the steering wheel failed to operate as needed. The vehicle was uncontrollable and started drifting towards the left before crashing into the highway barrier. The message “Electronic Driver Assist” was displayed. The vehicle was towed to the body shop. The manufacturer was contacted by phone, and the contact spoke with a customer representative, and a case was opened. The contact was informed that the investigating team would reach out in 2 to 4 days. An inspector had been assigned by Geico Insurance Company. The approximate failure mileage was 59,000.
- Power train
The 48-Volt Lithium-Ion eTorque Hybrid Battery Pack (Mopar Power Pack Unit/PPU) on my 2019 Jeep Wrangler Sahara Unlimited (~55K miles) failed. The failed component may be available on video by the dealership. Check engine light first appeared early XXX. Earliest dealership appointment was late…
The 48-Volt Lithium-Ion eTorque Hybrid Battery Pack (Mopar Power Pack Unit/PPU) on my 2019 Jeep Wrangler Sahara Unlimited (~55K miles) failed. The failed component may be available on video by the dealership. Check engine light first appeared early XXX. Earliest dealership appointment was late August 2026. At that visit, dealer diagnosed DTCs P0A94 (recurring, including P0A94-03) and U0412, and performed a software update flashing the BPCM (Battery Pack Control Module) firmware from 05057870AN to 05057870AV per a Technical Service Bulletin. This was covered under warranty at no charge; vehicle was returned to me. Days later, the check engine light returned along with a battery warning light and additional indicators, including ABS among others I could not fully identify. The vehicle then lost power and stopped running while in the roadway, disabled in an active lane of travel — a safety hazard to myself and surrounding traffic. Vehicle was towed to the dealership XXX. On this second visit, the dealership attributed the failure to moisture exposure and corrosion at the PPU connector/harness, denied warranty coverage, and charged me $4,561.90. I received the repaired vehicle XXX. I opened a case with Stellantis Customer Care (Case #XXX) with case manager [XXX] to request a technical review of the failure and the warranty denial. [XXX] stated he contacted the dealership five times seeking information or resolution and received no response. He offered rental car reimbursement up to $50/day during the repair. Dealership diagnosed and repaired the vehicle on both occasions. No known inspection by manufacturer, police, or insurance beyond the review requested under Stellantis case #XXX. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Lane departure › Blind spot detection
My 2019 Jeep Wrangler has experienced a failure of the Blind Spot Monitoring system. The vehicle repeatedly displays a “Blind Spot Alert Temporarily Unavailable” warning, causing the blind spot detection system to become unavailable while driving. The vehicle was inspected and diagnosed by an…
My 2019 Jeep Wrangler has experienced a failure of the Blind Spot Monitoring system. The vehicle repeatedly displays a “Blind Spot Alert Temporarily Unavailable” warning, causing the blind spot detection system to become unavailable while driving. The vehicle was inspected and diagnosed by an authorized Jeep dealership. Diagnostic trouble codes were present, and I was advised that Stellantis has issued a service bulletin addressing this condition and that the diagnostic codes indicate replacement of the mirror glass/components associated with the blind spot monitoring system. This concerns me because the system is an important safety feature designed to alert the driver to vehicles located in areas that may not be visible in the mirrors. When the system fails, those warnings are unavailable. Despite this being a documented issue addressed by a manufacturer service bulletin, I was informed that there is currently no recall and that the necessary mirror replacement is not covered under my extended warranty. I am filing this complaint because I believe a recurring failure involving a vehicle safety system should be documented and investigated to determine whether other Jeep Wrangler owners are experiencing the same problem and whether further manufacturer action is warranted.
- Service brakes
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, one of the brake calipers locked up, causing the vehicle to veer from side to side during acceleration. The vehicle was driven to an independent mechanic, where a technician diagnosed it with a…
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, one of the brake calipers locked up, causing the vehicle to veer from side to side during acceleration. The vehicle was driven to an independent mechanic, where a technician diagnosed it with a seized brake caliper. Due to the constant dragging, the brake pads wore excessively and failed to slow the vehicle properly, extending the stopping distance. The brake parts were replaced, and the vehicle was repaired.
- Service brakes
The left front brake line has failed and needed replacement on 2 occasions. The brake line gets a restriction that causes the vehicle to veer to the right under braking. It also is causing uneven rotor and caliper ware resulting in a high pitched squeal under load.
- Electrical system · Service brakes · Steering
While driving my 2019 Jeep Wrangler, the vehicle suffered a major electronic/CAN-network failure. Service Shifter, ABS and ESC warnings appeared, the wipers activated on their own, controls malfunctioned, and power-steering assistance failed while the vehicle was moving, making it extremely…
While driving my 2019 Jeep Wrangler, the vehicle suffered a major electronic/CAN-network failure. Service Shifter, ABS and ESC warnings appeared, the wipers activated on their own, controls malfunctioned, and power-steering assistance failed while the vehicle was moving, making it extremely difficult to steer. My two young children were in the vehicle. Jeep dealer diagnostics showed widespread communication faults involving steering, ABS/brake, transmission and other control modules. The dealer replaced the power-steering assembly and RF Hub, but the problem remains. On the first drive after repair, the ABS and ESC warnings repeatedly flashed on and off at highway speed. Interior lights are also flickering. I am concerned another network failure could again disable steering assistance or compromise ABS/braking-related safety systems and cause loss of vehicle control or a crash.
- Electrical system
Vehicle went into dealer for diagnostic, update PCM for hill start assist and cruise control failure. Dealer identified pcm update was not done when clutch recall performed. Instrument cluster update was pushed as well. Instrument cluster bricked. headlight indicator only functioning light on…
Vehicle went into dealer for diagnostic, update PCM for hill start assist and cruise control failure. Dealer identified pcm update was not done when clutch recall performed. Instrument cluster update was pushed as well. Instrument cluster bricked. headlight indicator only functioning light on cluster. All gauges and information screen are dark. no functionality. Car has been sitting at the dealership since July 1, 2026 waiting on a replacement instrument cluster.
- Electrical system · Engine · Steering
2019 Jeep Wrangler JLU experienced intermittent CAN-C communication failure. Vehicle has repeatedly experienced simultaneous loss of multiple electronic systems. On September 7th 2026, while driving, vehicle unexpectedly lost electric power steering, windshield wipers activated without command…
2019 Jeep Wrangler JLU experienced intermittent CAN-C communication failure. Vehicle has repeatedly experienced simultaneous loss of multiple electronic systems. On September 7th 2026, while driving, vehicle unexpectedly lost electric power steering, windshield wipers activated without command, ABS/TPMS/ESC warning lights illuminated, and vehicle subsequently would not shift into gear after stopping at a traffic light. Hazard lights would not activate. After shutting vehicle off, vehicle would not enter ACC or restart normally. Opening driver’s door unexpectedly caused vehicle to enter ACC. Manipulating the CAN-bus wiring/STAR connector behind the glove box has historically temporarily restored normal operation. Vehicle has previously required repair to this wiring/connector, and the failure has recurred. This has been occurring for at least 3 years and since 60,000 miles. This presents a significant safety hazard because steering assistance, shifting/propulsion, and signaling were simultaneously affected while driving. It is a known Chrysler issue (FCA STAR Case S2108000146) and should be recalled as there is a CLEAR and present danger with this ongoing issue.
- Steering
Getting the well know Jeep "Death Wobble". Was advised by Carvana when I bought this vehicle that it had an open recall for this exact issue (Manufacturer Recall Number CDJR XF1) due to the Steering Damper having air in it. However, when I contacted a Jeep dealership to get it fixed, I was told…
Getting the well know Jeep "Death Wobble". Was advised by Carvana when I bought this vehicle that it had an open recall for this exact issue (Manufacturer Recall Number CDJR XF1) due to the Steering Damper having air in it. However, when I contacted a Jeep dealership to get it fixed, I was told there is no recall for the Steering Damper for my specific vehicle. When I look it up on NHTSA, there isn't a recall listed on here either. Whenever I hit transitions in the pavement while driving above 50mph, I get the death wobble on the front of the vehicle. I have not yet had it repaired, but I plan to do so regardless of whether a recall exists. This is clearly an affected vehicle that was wrongly excluded from the manufacturer's recall for the Steering Damper on vehicles manufactured prior to August 11, 2020. My vehicle was manufactured in April 2019, so it is definitely in the correct date range, and with the exact same issue of others that were recalled. The only reason I have not crashed is because I've taken EVOC classes (for driving firetrucks and ambulances), and I am able to control it when it does happen. There were approximately 65k miles on the vehicle when I bought it, and there is about 72k miles now. It has been happening since I bought it in December 2025 from Carvana.
- Electrical system
The IPC Cluster completely blank. Unsafe to operate vehicle, as speed was unknown, unable to read fuel gauges, and unable to see any warning lights. Experienced the exact problem noted in Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, and my VIN is not listed on the recall list.
- Electrical system · Service brakes · Steering
Check engine, ABS, Service Shifter suddenly pops up and the steering was hard to turn almost had an accident
- Unknown or other
The IPC Cluster stopped working and the screen is completely blank. It is unsafe to drive since I don’t know how fast I’m going, how much gas is in the tank, and inability to see any warning lights. The recall for this is Recall Campaign 30B/NHTSA 24-V 652 for jeeps with the 3.5 inch cluster layout, which I have but my VIN is not listed on the recall list. It should be!
- Electrical system
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the instrument panel was blank. The vehicle was taken to the dealer and was diagnosed with instrument cluster failure. The contact was informed that the instrument cluster needed to be replaced.…
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving at an undisclosed speed, the instrument panel was blank. The vehicle was taken to the dealer and was diagnosed with instrument cluster failure. The contact was informed that the instrument cluster needed to be replaced. The vehicle was awaiting the repair. The manufacturer was notified of the failure and referenced NHTSA Campaign Number: 24V652000 (Electrical System); however, the VIN was not included in the recall. The failure mileage was unknown.
- Service brakes
ABS pump and module combination is making brake calipers to not released. It’s been two times in 6 months my brakes are used up and calipers locked. Jeep knows this issue across its brand of vehicles but not called for a recall. Parts are also in back order that says lot of vehicles has issues. Confirmed with local dealership.
- Electrical system
The 3.5-inch Instrument Panel Cluster went completely black while operating the vehicle, causing a total loss of speedometer and critical safety indicators (violating FMVSS 101). Concurrently, the engine computer limited vehicle performance to 3,000 RPM (limp mode). The vehicle exhibits the exact…
The 3.5-inch Instrument Panel Cluster went completely black while operating the vehicle, causing a total loss of speedometer and critical safety indicators (violating FMVSS 101). Concurrently, the engine computer limited vehicle performance to 3,000 RPM (limp mode). The vehicle exhibits the exact failure mode detailed in NHTSA Campaign 24V-652 (Jeep Recall 30B), but the manufacturer has not yet added this VIN to the recall population.
- Engine · Power train
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE…
VEHICLE & INCIDENT: 2019 Jeep Wrangler JL 2.0L Turbo. While climbing an extended grade on Hwy 87, vehicle experienced a sudden sluggish throttle anomaly and rapid coolant temperature spike from ~215F to 255F under load. Vehicle was pulled off and shut down within ~20 seconds. SUSPECTED FAILURE MODE & UNDERHOOD FIRE: Upon opening the hood, pressurized coolant had sprayed across the engine bay from a split in the smaller rubber hose branch of the engine coolant outlet assembly (Mopar PN 68280797AC). The hose split longitudinally ~13mm with the center ~32mm from the hose end. The vehicle is equipped with a Baja Designs T-Fitting to replace 68280784A The hot, pressurized coolant sprayed directly onto the exposed, center section of the turbocharger between the compressor and turbine sections and on the turbine section itself. The coolant is suspected to have flash-ignited on contact with the turbo, creating an active under hood fire that began spreading to the hood insulation liner. The fire was successfully doused roadside with water, preventing a total vehicle burn-down. No other fuel sources were noted and the lines to the turbocharger were intact and did not show evidence of a leak. SAFETY CONCERN / HAZARD FOR NHTSA: 1. FIRE HAZARD: Pressurized factory coolant hoses and plastic junctions on the 2.0T GMET4 are routed in close proximity to the unshielded turbine housing. A hose rupture under normal grade-climbing thermal loads results in high-pressure atomized coolant hitting an ignition source well above its auto-ignition point. 2. COMPONENT DEGRADATION: Rubber lines near the engine outlet appear susceptible to heat-fatigue failure under high ambient/high load conditions, posing a sudden fire hazard at highway speeds. REPAIR: Roadside trim/re-clamp of the split hose allowed temporary transit. Replacing full hose assembly (68280797AC), upgrading radiator lines, and performing a full OAT coolant flush/vacuum refill. No oil contamination was noted after the incident.
- Structure › Body
The vehicle is experiencing severe, premature galvanic corrosion on the doors, hinges, and hood due to a documented factory defect where aluminum panels press directly against steel hinges without proper isolation (acknowledged by the manufacturer in TSB 31-001-24).This is a critical structural and…
The vehicle is experiencing severe, premature galvanic corrosion on the doors, hinges, and hood due to a documented factory defect where aluminum panels press directly against steel hinges without proper isolation (acknowledged by the manufacturer in TSB 31-001-24).This is a critical structural and safety hazard covered under Federal Motor Vehicle Safety Standard (FMVSS) 206, which regulates door locks and door retention components. The advanced sub-surface corrosion is causing the metal surrounding the door hinges to degrade and oxidize, causing the paint to blister, bubble, and flake off. Over time, this structural failure poses an imminent safety risk of causing the door hinges to seize or bind, potentially jamming the doors shut during an emergency and trapping occupants inside the vehicle. Furthermore, the degradation of these hinge components creates a severe risk of the doors failing and opening unexpectedly while the vehicle is in motion at highway speeds.The manufacturer is refusing to address this structural defect because the vehicle passed its 5-year calendar warranty window, ignoring the fact that this sub-surface chemical reaction takes years to visibly manifest. This defect requires a formal safety investigation and an expanded recall to protect drivers from door-retention failures.
- Engine · Service brakes, hydraulic
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 60 MPH, the vehicle suddenly lost motive power and stalled, and the vehicle went into LIMP Mode. The check engine warning light was illuminated. The driver was able to safely move the vehicle to the side of…
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 60 MPH, the vehicle suddenly lost motive power and stalled, and the vehicle went into LIMP Mode. The check engine warning light was illuminated. The driver was able to safely move the vehicle to the side of the road. The vehicle was taken to an independent mechanic to be diagnosed, and the contact was informed that the ABS module had failed. The local dealer was contacted and advised that the replacement part was on backorder and referred the contact to the manufacturer for assistance. The vehicle was not diagnosed or repaired. The manufacturer was contacted and confirmed that the replacement part was not available. The failure mileage was approximately 68,482.
- Steering
The contact owns a 2019 Jeep Wrangler. While the contact's daughter was driving at an undisclosed speed, the heated steering wheel feature was enabled; however, the heated steering wheel feature failed to function as intended. In addition, the contact became aware of a burning odor. The contact…
The contact owns a 2019 Jeep Wrangler. While the contact's daughter was driving at an undisclosed speed, the heated steering wheel feature was enabled; however, the heated steering wheel feature failed to function as intended. In addition, the contact became aware of a burning odor. The contact deactivated the heated steering wheel feature. The vehicle was taken to the dealer, where it was diagnosed with interior melting of the steering wheel. The contact was informed that the steering wheel and the steering wheel housing needed to be replaced. The vehicle was not repaired. The contact was informed that the parts were ordered. The contact referenced an unknown recall; however, the VIN was not associated with a recall related to the failure. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline and report the failure. The failure mileage was approximately 71,663.
- Electrical system
Instrument panel cluster has malfunctioned. Spedometer, tachometer, odometer, fuel guage, oil temperature, tire pressuer, and several other dashboard displays both analog and digital are not functional. The instruments on the dashboard have gone blank and do not provide a reading when the car is…
Instrument panel cluster has malfunctioned. Spedometer, tachometer, odometer, fuel guage, oil temperature, tire pressuer, and several other dashboard displays both analog and digital are not functional. The instruments on the dashboard have gone blank and do not provide a reading when the car is powered on. As a consequence of the instrument panel cluster failure, I am unable to see my exact speed, potential vehicle warning indications, and fuel levels while operating the vehicle putting the safety of myself and others at risk. The vehichle has a history of dealership and mechanic inspections. No warning lamps, messages, or other symptoms were evident prior to the failure of the instrument panel cluster.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Frame weld deficiencies
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was…
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received information from the vehicle manufacturer Fiat Chrysler Automobiles (FCA) via information request letters dated March 8, 2019, and February 6, 2020. Supplemental requests for information occurred between July 2020 and July 2023. A review of the responsive manufacturer information showed that vehicles presenting an unexpected reduction in steering ability due to a welding tool misalignment were correctly addressed via recall 18V-675. General complaints concerning the weld appearance were not associated with a realized risk to motor vehicle safety. ODI identified a limited number of reports involving weld separation on vehicles that were out of scope of recall 18V-675. FCA identified various causes of weld quality issues in early production (build dates prior to March 2018) including improper welding techniques on galvanized frames and component part variation leading to off-seam welds. These issues were addressed in production for subject vehicles built after July 2018 and preceded a drop in weld failure reports. ODI reviewed manufacturer and agency reports of weld failures out of scope of recall 18V-675 and did not find any that resulted in a loss of vehicle control. There are no known crashes, injuries, or fatalities as a result of weld failures on vehicles not included in recall 18V-675. Due to the steering related consequence associated with Recall 18V-675, ODI opted to include a request for information regarding various steering issues experienced by vehicles included in this investigation. ODI reviewed manufacturer as well as agency data and determined these various steering issues were not related to any weld defect. Since the opening of this investigation, FCA has addressed the following steering concerns; a. Steering looseness due to material choice in the steering box internal components. FCA released an updated part with an internal component material less sensitive to temperature variances (TSB 08-003-21 REV. A).NHTSA will take further investigative action if justified. b. Steering wobble or shimmy due to a manufacturing and design deficiency in the steering damper. FCA released a part via Customer Satisfaction Notification (CSN) V41 in June 2019 which implemented supplier quality control improvements and design changes due to the presence of air in the base valve which degraded damping performance.NHTSA will take further investigative action if justified. c. Steering stiction, or loss of power steering, due to an underpowered steering pump calibration that occurred at highway speeds during cold weather. In December 2021, FCA released CSN Y95 which corrected this issue via software update. Due to the decreased number of consumer complaints, the service campaign appears to have addressed the issue related to an underpowered steering pump. NHTSA will take further investigative action if justified. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
- Frame Weld Deficiencies
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies…
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, NHTSA has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detachments that were outside of the scope of NHTSA Recall No. 18V-675. Additionally, the information that FCA provided did not adequately address whether frame weld quality deficiencies compromise the structural integrity of vehicles, and therefore may pose an unreasonable risk to motor vehicle safety. Finally, ODI needs to further evaluate the alleged steering-related defects reported through MY 2019 and the alleged defects' relation to weld quality.The petition was granted on September 16, 2019. Preliminary Evaluation PE19-012 has been opened to further assess the scope, frequency, and potential safety-related consequences of alleged weld quality deficiencies and steering related concerns on the MY 2018-2019 'JL' Jeep Wrangler vehicles.The ODI reports cited above can be viewed on NHTSA.gov under the following reference numbers:11234967, 11222390, 11219370, 11217080, 1204905, 11179954, 11171786, 11161243, 11155523, 11153044, 11143617, 11142722, 11142426, 11141336, 11141035, 11140637, 11140344, 11140262, 11140085, 11140057, 11139880, 11139866, 11139557, 11139467, 11139436, 11138974, 11138758, 11138757, 11132030, 11129738, 11129667, 11124312, 11120232, 11119676, 11119650, 11119454, 11119450, 11115658, 11115137, 11113029, 11112515, 11110583, 11109903, 11093172, 11088501, 11076098
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011901Warranty Bulletin ID-23-03 Rev. H 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
- 11011898Warranty Bulletin D-23-04 Rev. G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
- 11011505Buzz Squeak Rattle (BSR) From Speaker Sound Bar At High Volume Level.
- 11011504Buzz Squeak Rattle (BSR) From Sound Bar Or Sport Bar Area.
- 11011171Damper - none
- 11011150Cover kit - hood
- 11010511Tire Pressure Monitor (TPM) Service Information. TPM Lamp On.
- 11010496Warranty Bulletin D-23-09 Rev. A (XF1) Steering Damper Select 2018 - 2020 Jeep Wrangler (JL), 2020 Jeep Gladiator (JT) and 2018 Jeep Wrangler (JK)
- 11010487FCA Caribbean Warranty Bulletin ID-23-10 Rev. A (XF1) Steering Damper Select 2018 - 2020 Jeep Wrangler (JL), 2020 Jeep Gladiator (JT) and 2018 Jeep Wrangler (JK)
- 11010476"Air Trapped in Steering Damper Warranty Extension XF1 A shimmy in the steering wheel after hitting an irregularity on the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."
- 11010473"Air Trapped in Steering Damper Warranty Extension XF1 A shimmy in the steering wheel after hitting an irregularity on the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."
- 11010205Plate - Planetary
- 11009561Switch - headlamp
- 11009540Heated Steering Wheel Inoperative And Or Not Hot Enough.
- 11008973FCA Caribbean Warranty Bulletin ID-23-03 Rev. G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
- 11008972Warranty Bulletin D-23-04 Rev. F 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
- 11008707Switch - headlamp
- 11008697FCA Caribbean Warranty Bulletin ID-23-03 Rev.F 2018 - 2024 (Current) Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
- 11008356Warranty Bulletin D-23--04 2018 - 2024 (Current) Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification
- 11008326Antilock Brake System (ABS) Module Will Not Initialize After Recent Service Replacement.
- 11008246Bow - folding top
- 11007984Low Tire Pressure. Tire Valve Stem And Tire Pressure Monitor (TPM) Sensor Service.
- 11007954Battery Drain Suspected or "Identified" From USB or Media Hub
- 11006887Wheel - steel
- 11006814Pump water & connector - oil cooler tube
- 11006622Click Noise From Front End While Driving And Or Turning.
- 11006516Shimmy Felt In Front End
- 11006240Griding/Gear Clash From Transfer Case When Going Into 4WD, Above 5 mph (8 kph).
- 11006237WARRANTY BULLETIN D-23-04 2018 - 2024 (Current) Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. D)
- 11005356Carrier planetary & shaft kit - output
- 11005320"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
- 11003796Water Leak From Front Door. Water On Front Floor.
- 11002828"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
- 11002424Wiperunit - windshield wiper, blade - front wiper
- 11002351Pump water & connector - oil cooler tube
- 11002350Pump water & connector - oil cooler tube
- 11002315Wiperunit - windshield wiper, blade - front wiper
- 11002314Wiperunit - windshield wiper, blade - front wiper.
- 11002019SWITCH Power Window Before replacing the window switch, please follow these steps: 1.- Review the master window Switch for any physical issue (Button stuck, broke). If not, physical issue is found move to next step 2.- Make sure all the switches harness are properly connected, disconnect the switch and reconnect it, and reverify the issue. If after performing these steps the switch remains faulty, please replace the switch
- 11001459Suspected Engine Coolant Leak
Every Jeep Wrangler model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.