2006 Toyota RAV4
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › RAV4 › 2006
These records cover every 2006 Toyota RAV4. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
11 recalls name the 2006 Toyota RAV4. Newest first.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2011 Toyota RAV4 vehicles manufactured October 31, 2005, to September 7, 2010, and 2010 Lexus HS250h vehicles manufactured July 6, 2009, to August 26, 2010. The affected vehicles have rear suspension arms (rear tie rods) with adjusting lock nuts that may have been…
Risk and remedy
Risk
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010…
Risk and remedy
Risk
If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy
SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2012 RAV4 vehicles manufactured July 28, 2005, to December 19, 2012, and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the event of a frontal collision, the rear seat belts for the outboard seats may be cut by the seat cushion frame.
Risk and remedy
Risk
A cut seat belt may not properly restrain the seat occupant, increasing their risk of injury in a crash.
Remedy
Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window…
Risk and remedy
Risk
If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy
Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a…
Risk and remedy
Risk
If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy
Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust leading to thread damage and…
Risk and remedy
Risk
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust, leading to thread damage and…
Risk and remedy
Risk
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
Toyota IS recalling certain model year 2008 through 2011 lexus lx570, 2003 through 2009 toyota 4runner, and 2006 through 2010 RAV4 vehicles. the accelerator pedal can get stuck in the wide open position due to its being trapped by an unsecured or incompatible driver's floor mat.
Risk and remedy
Risk
A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death.
Remedy
The remedy IS now available. the safety recall began early april 2011. The remedy will involve modification or replacement of the accelerator pedal and replacement of any toyota all-weather floor mat. owners may contact toyota at 1-800-331-4331 or lexus at 1-800-255-3987.
Gulf states toyota IS recalling certain model year 2005-2010 vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold between september 1, 2005 and june 2, 2008 without the requisite load carrying capacity modification labels.
Risk and remedy
Risk
This does not meet the standard requirements.
Remedy
Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. Dealers will also correct the owner's manual. the safety recall began on may 27, 2010. owners may contact gulf states toyota at 713-580-3300.
Southeast toyota IS recalling certain model year 2005-2011 passenger vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold without the requisite load carrying capacity modification labels.
Risk and remedy
Risk
A driver may overload a vehicle which may increase the risk of a crash.
Remedy
Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. the safety recall began on may 27, 2010. owners may contact southeast toyota at 1-800-301-6859.
Toyota IS recalling 27,080 model year 2005 through 2010 passenger cars built from september 1, 2005 to may 4, 2009. these vehicles were not equipped with load carrying capacity modification labels which fails to conform with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims."
Risk and remedy
Risk
Incorrect load carrying capacity modification labels could result in the vehicle being overloaded, increasing the risk of a crash.
Remedy
Toyota will notify owners and provide them with a new, accurate label to be installed over the inaccurate label free of charge. the safety recall began on august 18, 2009. owners may contact toyota at 1-888-270-9371.
Owner complaints
705 complaints26 involved a crash5 involved a fire10 injuries1 deaths
What owners report most
Latest complaints
- Structure › Body · Suspension
2016 Superseding Recall (Campaign 16V596000): Toyota issued a follow-up recall because some initial epoxy repairs were not enough. Dealers must replace both rear suspension arms and encapsulate the locknuts completely free of charge. These parts are severely rusted and corroded on my 2006 Toyota…
2016 Superseding Recall (Campaign 16V596000): Toyota issued a follow-up recall because some initial epoxy repairs were not enough. Dealers must replace both rear suspension arms and encapsulate the locknuts completely free of charge. These parts are severely rusted and corroded on my 2006 Toyota Rav4. It seems like my vehicle was not included in the recall when it should have been. I am not the original owner, but it seems like the issue was never addressed. The damage was discovered during routine maintenance. I purchased the vehicle on 8/1/2024. The damage must have existed before then based on the amount of damage. Is it possible for Toyota to still extend the recall to this vehicle?
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2006 Toyota Rav4. The contact discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 122,000, and at the time of registration, it was discovered that the mileage was 199,694.
- Suspension
My 2006 Toyota RAV4 was supposedly repaired under the rear suspension arm recall (C0J / G0V), but the rear tie rod ends still have yellow stickers reading “this is a recalled part” and no epoxy on the bolts. A Toyota dealer refused to inspect the vehicle and relied solely on the VIN record. The car…
My 2006 Toyota RAV4 was supposedly repaired under the rear suspension arm recall (C0J / G0V), but the rear tie rod ends still have yellow stickers reading “this is a recalled part” and no epoxy on the bolts. A Toyota dealer refused to inspect the vehicle and relied solely on the VIN record. The car now rides roughly, and I believe additional suspension components have been damaged due to the unresolved recall. I am concerned for my safety and request NHTSA investigation.
- Steering
For several months the 2006 Rav4 with only 118k miles had been experiencing intermittent failure of power steering while driving at speeds between 5-20mph. These failures resulted in the steering wheel to become extremely difficult if not impossible to turn while the car is driving. In each…
For several months the 2006 Rav4 with only 118k miles had been experiencing intermittent failure of power steering while driving at speeds between 5-20mph. These failures resulted in the steering wheel to become extremely difficult if not impossible to turn while the car is driving. In each incident, this resulted in stopping the car and putting on emergency lights until we can safely turn off the car and hopefully the issue goes away several minutes later. This issue has proven to be very dangerous when in traffic with no place to pull over and with the steering tightening up, it is not even possible to pull over in most cases. Four different mechanical shops tried to replicate the issue and none were able to determine the root cause nor replicate it consistently. This issue has been happening more frequently now and the car cannot be taken out safely. As [XXX] drivers, this is not safe by any means and Toyota should consider this a critical safety recall and cover towing costs to move this. There are no signs of instrument lights or any leaks coming from the car. This seems to be entirely a malfunction of steering components. With regard to incidents resulting from this, my mother is the primary driver, she is [XXX] old and injured her wrist trying to move the steering wheel to a safe location. Her wrist is still in pain several days later. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure › Body
Rear subframe rusted out. I took it in because my car started sounding like the Titanic after it hit an iceberg. The mechanic described it as “a giant hole in the bottom of the car.” I read there were recalls on frames for other Toyotas, but we kept up with every recall on this vehicle and the…
Rear subframe rusted out. I took it in because my car started sounding like the Titanic after it hit an iceberg. The mechanic described it as “a giant hole in the bottom of the car.” I read there were recalls on frames for other Toyotas, but we kept up with every recall on this vehicle and the subframe was never listed as an issue. I get a regular multipoint inspection at the Toyota dealership about every six months, and no one caught this. I was told it is not safe to drive, and will snap at any time. I am lucky I did not crash.
- Suspension
The vehicle is owned and operated in Costa Rica. I submitted the vehicle for the 4 incomplete recall items associated with its VIN. I was told by Grupo Purdy Toyota of Costa Rica that Manufacturer Recall Number G0V NHTSA Recall Number16V596 does not apply in Costa Rica and they declined to complete the recall remedy. Is this correct or should they be completing the recall remedy?
- Unknown or other
I notified Toyota of an issue with my car a couple years ago. One day I came out to find my car missing big portions of paint (it had been a windy night); all of the paint in the attached photos came off in a single night and day, which is not normal paint performance. I came to find out that…
I notified Toyota of an issue with my car a couple years ago. One day I came out to find my car missing big portions of paint (it had been a windy night); all of the paint in the attached photos came off in a single night and day, which is not normal paint performance. I came to find out that other years for the same make and model had a recall program for "pearl white paint". The issue seemed to be affecting my vehicle too. With large portions of paint peeling freely of the body of my vehicle, it began to rust. Rust eroding the structure of a vehicle can make the car unsafe for drivers and passengers. In an accident situation, the structure of the vehicle may be compromised by the rust, leading to more severe harm to occupants. Additionally, if the roof of the car is compromised, moisture could leak into the interior systems and cabin space, leading to other hazards, with potentially severely harmful outcomes. Toyotas response to the photos, report from the dealership, and BBB complaint I filed was: "your vehicle has not been identified as one of the vehicles impacted by the pearl white paint issue". Therefore, I had to pay to repaint my whole vehicle out of pocket. It was clear from the pictures and report that the paint issue was directly affecting my vehicle, but Toyota refused to acknowledge this and rectify the hazard.
- Firerelated
The contact owned a 2006 Toyota Rav4. The contact stated that while his wife was driving at an undisclosed speed, she heard a scraping and shuddering sound at the hood of the vehicle. The contact then stated that another vehicle noticed a spark underneath the vehicle and notified his wife. The…
The contact owned a 2006 Toyota Rav4. The contact stated that while his wife was driving at an undisclosed speed, she heard a scraping and shuddering sound at the hood of the vehicle. The contact then stated that another vehicle noticed a spark underneath the vehicle and notified his wife. The contact’s wife was able to veer the vehicle off the road and exit the vehicle when the hood of the vehicle started to inflame. No warning lights were illuminated. No injuries were sustained. No medical attention was required. The fire department was notified and extinguished the fire. A police report was filed. The vehicle was towed to a tow lot and deemed a total loss by the insurance company. The vehicle was not diagnosed or repaired. The dealer nor the manufacturer were notified of the failure. The failure mileage was approximately 180,000.
- Engine
Two days ago my car was driving perfectly on the highway. The oil pressure light turned on I turned off the highway immediately and put more oil in the car. At this point my car is consuming over a quart every week and I don't drive more than a couple of hundred miles every week. I've taken several…
Two days ago my car was driving perfectly on the highway. The oil pressure light turned on I turned off the highway immediately and put more oil in the car. At this point my car is consuming over a quart every week and I don't drive more than a couple of hundred miles every week. I've taken several longer trips with this car. I started the car back up after checking the oil level, started driving and the light didn't come back on. About 10 more miles down the road on the highway the oil pressure light the check engine light vsc light the four-wheel drive light appear. I go to an AutoZone and I get a code p0012. I've done lots of research and I've learned that this is all related to Toyota's well-known defective design and manufacturing of their engines. I have a 2az Fe engine. I bought this car with 125,000 miles on it in 2020. It now has about 154,000 mi on it. I didn't know that the oil consumption was extreme until this point of research. Now my car is making a rattling sound most likely the engine needs to be replaced. Technically yes I can drive it but it will stall and probably light on fire if I do and this is dangerous. They had a TSB warranty extension in 2016 I believe. I did not own the car that time nor do I know if that car was even subjected to the extension notice. But it is well known engine can do this and the Pistons fail around this mileage that my car has. It's out of warranty but I'm reading everywhere people having problems with this year's car and the other cars with this engine right now. There's a whole group of engines that are starting to fail because of these poorly designed Pistons that can affect oil leakage. Not only wasting a precious resource but causing a very dangerous situation for drivers. This should be addressed by Toyota still I want them to fix my engine or replace it before I cause an accident that can lead to death. I'm choosing to not drive it right now but I don't have the luxury of a second car. I may have to drive it.
- Engine
2006 Toyota Rav4 with 2.4 liter engine burning oil rapidly. Burning approximately 4 quarts of oil in 3,000 miles. Vehicle currently has 100,000 miles. Issue persists even though I maintain routine maintenance on the vehicle. Luckily no safety hazards have occurred yet, but there is a high risk for…
2006 Toyota Rav4 with 2.4 liter engine burning oil rapidly. Burning approximately 4 quarts of oil in 3,000 miles. Vehicle currently has 100,000 miles. Issue persists even though I maintain routine maintenance on the vehicle. Luckily no safety hazards have occurred yet, but there is a high risk for potential safety hazard. Vehicle has been inspected by 3 different mechanics. I have been told by 3 different mechanics that this is a common issue for cars with this year/engine. About 2,800 miles after high synthetic oil change the vehicle begins to sound like it is struggling to accelerate at low speeds and the check engine oil light will briefly turn on at random then go away. Light does not stay lit or continuously flicker.
- Steering › Linkages
The contact owns a 2006 Toyota Rav4. The contact stated that while making a right or left turn, there was a loud popping sound coming from the steering wheel. There was no warning light illuminated. Additionally, the contact stated that the popping noise was progressively louder while steering to…
The contact owns a 2006 Toyota Rav4. The contact stated that while making a right or left turn, there was a loud popping sound coming from the steering wheel. There was no warning light illuminated. Additionally, the contact stated that the popping noise was progressively louder while steering to make a turn. The vehicle was taken to a local dealer where it was diagnosed that the steering linkage needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 86,000.
- Steering
While my son was driving me the vehicles steering wheel locked and he was unable to steer the vehicle. It caused us to go off the road down a steep hill and wreck. I’ve never had any problems with this vehicle so it was completely unexpected. If there had been anyone in our path we wouldn’t of been able to stop from hitting them. It has not been inspected but there are witnesses to the accident
- Steering
Clunking noise when turning steering wheel right or left. Numerous complaints from 006 RAV 4 owners. Fear that my steering will fail and cause an accident or Death. The issue is a defective intermediate steering shaft. Toyota will not issue a recall and will only repair if vehicle is still under warranty. How many complaints, accidents, or deaths will it take for this manufacturer to do the right thing???
- Unknown or other
My Toyota RAV4 started smoking by the headlights last night while I was driving on the highway. I pulled over and opened the hood to see what was happening and it burst into flames. The car completely burned. Nothing left! I see on the internet that other people have had this happen. Please investigate.
- Engine
excessive oil consumption 1 1/2 quart oil every 600 miles
- Unknown or other
The rear subframe in my '06 Toyota RAV4 has rusted through. This is a key structural part of the vehicle, all of the rear suspension components attach to this subframe, so it's concerning to see the integrity of the subframe completely compromised. The component has not been inspected by the…
The rear subframe in my '06 Toyota RAV4 has rusted through. This is a key structural part of the vehicle, all of the rear suspension components attach to this subframe, so it's concerning to see the integrity of the subframe completely compromised. The component has not been inspected by the manufacturer, police, or insurance representatives. There were no warning lamps or symptoms of the failure. I happened to be under the car checking out an issue with a heat shield when I happened to notice the frame condition.
- Engine
This 2006 Rav4 engine is known for its massive oil consumption due to the faulty piston rings. Always kept oil in it and had regular changes because of this issue. Checked the oil 2 days prior to the engine failure, and all was well. Driving down the hwy going around 70mph, the engine started to…
This 2006 Rav4 engine is known for its massive oil consumption due to the faulty piston rings. Always kept oil in it and had regular changes because of this issue. Checked the oil 2 days prior to the engine failure, and all was well. Driving down the hwy going around 70mph, the engine started to lose power and sound funny (high rpm sounds with no power), so I took my foot off the gas and coasted for a few seconds. Down to 50mph, I hit the gas pedal, and then a loud BOOM happened and car shook. Smoke from the engine, and then all the dash lights came on. Lost all power. Looked under the engine and a piston had blown a hole through the bottom of it. Needs new engine now. Mechanic inspected it and they documented with a picture. Thankfully I was not injured as that could have caused a serious wreck, especially if there was someone behind me. I've read about these engines being blown regularly online. Even some before 100k miles. No warnings before this happened.
- Wheels
This complaint IS related to discovery SRX p215/70r16 cooper tires which were bought on october 23 2018. These tires are identical to recall 'nhtsa recall no. - 19t-005 affecting cooper discoverer' and cooper evolution' tires' only they are the 16 inch tires. We believe that the 16 inch tires…
This complaint IS related to discovery SRX p215/70r16 cooper tires which were bought on october 23 2018. These tires are identical to recall 'nhtsa recall no. - 19t-005 affecting cooper discoverer' and cooper evolution' tires' only they are the 16 inch tires. We believe that the 16 inch tires should also be included in this recall. here are the issues that we have had with these tires: 1.10-23-18 purchased discovery SRX p215/70r16 cooper tires with road hazard from blains farm & fleet in verona wi vehicle miles 106292 2.10-28-18 rear passenger tire blew for no reason, changed and returned to blains for replacement (no receipt was given) 3.11-25-18 while driving home and rounding a corner, the car veered into a curve and destroyed the front passenger tire, rim, and wheel covers on both wheels. Rear tire was also replaced because of bulge on tire. We paid the $770.46 because we thought it was our fault but now are wondering if this was a tire issue too. Mileage 107274 4. 02/21/2019 found bulge in rear passenger tire, replaced tire at blains farm and fleet 5.2/27/19 had alignment checked because tire felt like they were noisy and wondering if there was another problem with the tires. 6.04/16/21 found bulge in drivers side front tire and will have replaced. Called david at cooper to explain all of the issues we have had say that the failures align with recall 19t-005 except for the size of the tire. He said they could not do anything except wanted us to take the tire with the bulge to the dealer, which will do.
- Electrical system · Exterior lighting · Steering
For some time there has been an intermittent problem with the dashboard lights coming on and loss of power steering. The car has been checked by mechanics, including one at a toyota dealership, but the problem was not found. I have experienced the problem with the car stationary, but I believe my son said it has happened to him while in motion.
- Engine
TL* the contact owns a 2006 toyota RAV4. The contact stated that the vehicle was consuming oil at an excessive rate. The contact took the vehicle to a certified mechanic who stated that the oil was leaking and excessively burning to the extent that it could cause a possible engine failure. The…
TL* the contact owns a 2006 toyota RAV4. The contact stated that the vehicle was consuming oil at an excessive rate. The contact took the vehicle to a certified mechanic who stated that the oil was leaking and excessively burning to the extent that it could cause a possible engine failure. The vehicle had not been repaired. The manufacturer was made aware of the issue and informed the contact that a warranty related campaign regarding the engine had been issued however, the time-frame was exceeded. The approximate failure mileage was 82,000.
- Steering
I bought a used 2006 RAV4 3.5 l V-6, after a month a bought it. I noticed when I turn left or right I heard a clunk sound. I found out that the intermediate steering shaft IS the problem. This common to most RAV4, dealership it's normal but to me it doesn't fell normal when I'm driving, it feels…
I bought a used 2006 RAV4 3.5 l V-6, after a month a bought it. I noticed when I turn left or right I heard a clunk sound. I found out that the intermediate steering shaft IS the problem. This common to most RAV4, dealership it's normal but to me it doesn't fell normal when I'm driving, it feels like something IS will come out or broke off. Kind of scary thing to feel when driving. I think the manufacturer should find a solution to this problem before someone could hurt or die.
- Engine
The engine IS burning oil due to bad piston rings. I did some digging found that that it was manufactured this way.
- Suspension
As a result of having recall 16v596000 performed, rear toe arms are no longer adjustable for alignments. Contacted toyota customer experience and was told they would not repair at their cost the manufacturing defect that causes premature rust, offered no solutions. Causes premature tire wear, loss of traction.
- Engine · Unknown or other
There was a recall regarding oil consumption. I took my vehicle to the dealer. They filled up the oil and told me to come back after 3000 miles but to not fill the oil. Halfway in, the oil was completely exhausted. because it had not been 3000 miles, I could not take it back for a fix. I had no…
There was a recall regarding oil consumption. I took my vehicle to the dealer. They filled up the oil and told me to come back after 3000 miles but to not fill the oil. Halfway in, the oil was completely exhausted. because it had not been 3000 miles, I could not take it back for a fix. I had no choice but to add oil or the engine blows. when I did take it back, I was given the response that the vehicle burns a normal amount of oil and I told them I had to fill it in between to avoid the engine blowing. they refused to fix the recall. I contacted toyota who also refused to fix the recall because the dealership had written "normal" consumption. the vehicle burns oil at a very rapid rate and I would like this recall performed on my vehicle.
- Fuel/propulsion system · Vehicle speed control
Had my 2006 toyota rav 4 in the dealership for recall services. I also had recommended maintenance tuneup and brake fluid drain and refill. When I left the parking lot of the dealership, I crossed 2 lanes of traffic, braked, waited for alternate traffic to pass before turning onto the city street…
Had my 2006 toyota rav 4 in the dealership for recall services. I also had recommended maintenance tuneup and brake fluid drain and refill. When I left the parking lot of the dealership, I crossed 2 lanes of traffic, braked, waited for alternate traffic to pass before turning onto the city street with my foot still on brake, the car accelerated, lurched then accelerated again without me pressing on the gas and continuing to brake when it accelerated. I called the dealership back the next morning and they towed it back in. After they performed several tests and test drive it they could not get it to duplicate the same thing. There were two previous occurrences that I did not report to this entity shortly after I purchased the car used. They happened close together and not again until the most recent event. I believe the prohibitive cost of throttle body and accelerator pedal module ($1,519.40) which are the necessary repairs to actually fix the problem and not the floor mats, IS why the previous owner sold the car to me. No warning forthcoming, even though I did ask.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Rear Suspension Arm Assembly Failure
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft…
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
- Unintended and Uncontrolled Acceleration
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested…
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
- 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
- 10227898TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10220174TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
- 10214323TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
- 10210375TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
- 10207946POL: This consolidated Tire Warranty Guide contains the complete warranty terms for all brands of ground and spare tires currently in use by Toyota. This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.
- 10204571TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10201400TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
- 10197476Replacement vin plates.
- 10197473Product general information.
- 10190460Toyota Safety Recall and Service Campaign - Technician Certification Requirements
- 10190453TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
- 10188913TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2021 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10187241TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
- 10186195TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions.
- 10177782TSB: OBSOLETE NOTICE June 23, 2020: This bulletin is now obsolete. Please see T-SB-0063-20.
- 10177781TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. ST005-01, SU001-08, and T-SB-0391-08. The aforementioned bulletins are obsolete, and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. This Service Bulletin provides best practice procedures for vehicle pulling complaint, diagnosis, and repair for 2002 ? 2021 model year Toyota vehicles. This information supplements Repair Manual procedures when the symptoms are: ?Vehicle Pulling: The vehicle moves to the right or left when the driver holds the steering wheel while driving straight ahead without exerting steering effort. ?Steering Wheel Off Center: The vehicle travels straight, but the steering wheel is not pointed straight ahead. The vehicle is not pulling. Before repairing a vehicle pulling to one side, it is necessary to clearly identify the cause of the pulling condition. Frequently, pulling to one side is diagnosed as a wheel alignment concern. However, the actual cause may be related to the lateral force generated by the tires, vehicle damage, road crown or worn components. Performing a wheel alignment when tire force is the cause could result in the wheel alignment being set at a value outside of specifications. This could then cause other problems such as uneven tire wear, etc. A customer may notice a pull to the left when in the left lanes of travel and notice a pull to the right or no pull when traveling in the right lanes of travel on the very same section of roadway. This road crown effect is environmental and cannot be corrected with suspension adjustments or any other wheel or tire modification discussed in this bulletin.
- 10177599These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
- 10177598These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.
Every Toyota RAV4 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.