2009 Toyota RAV4
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › RAV4 › 2009
These records cover every 2009 Toyota RAV4. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
15 recalls name the 2009 Toyota RAV4. Newest first.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2011 Toyota RAV4 vehicles manufactured October 31, 2005, to September 7, 2010, and 2010 Lexus HS250h vehicles manufactured July 6, 2009, to August 26, 2010. The affected vehicles have rear suspension arms (rear tie rods) with adjusting lock nuts that may have been…
Risk and remedy
Risk
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010…
Risk and remedy
Risk
If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy
SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2012 RAV4 vehicles manufactured July 28, 2005, to December 19, 2012, and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the event of a frontal collision, the rear seat belts for the outboard seats may be cut by the seat cushion frame.
Risk and remedy
Risk
A cut seat belt may not properly restrain the seat occupant, increasing their risk of injury in a crash.
Remedy
Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window…
Risk and remedy
Risk
If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy
Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2009-2012 RAV4 vehicles manufactured October 27, 2008, to December 19, 2012 and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the affected vehicles, water may drip onto the joint that connects the wiper linkage to the wiper motor.
Risk and remedy
Risk
Over time, the dripping water may cause corrosion and wear at the joint, potentially resulting in the separation of the wiper linkage. Once this occurs, the wipers would not function, reducing driver visibility and increasing the risk of a crash.
Remedy
Toyota will notify owners, and dealers will replace the water diverter channel. In addition, a new wiper linkage with a wiper motor crank arm will be installed. The wiper linkage will have a protective cover over the wiper linkage joint to minimize water splash and a retainer ring to prevent the wiper arm from separating from the wiper motor. The recall began on November 7, 2016. Owners may contact Toyota's customer service number at 1-800-331-4331.
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion…
Risk and remedy
Risk
Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy
SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust leading to thread damage and…
Risk and remedy
Risk
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013…
Risk and remedy
Risk
If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy
Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the…
Risk and remedy
Risk
If the switch overheats, it may melt, possibly resulting in a fire.
Remedy
Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust, leading to thread damage and…
Risk and remedy
Risk
Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy
Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
Toyota IS recalling certain model year 2008 through 2011 lexus lx570, 2003 through 2009 toyota 4runner, and 2006 through 2010 RAV4 vehicles. the accelerator pedal can get stuck in the wide open position due to its being trapped by an unsecured or incompatible driver's floor mat.
Risk and remedy
Risk
A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death.
Remedy
The remedy IS now available. the safety recall began early april 2011. The remedy will involve modification or replacement of the accelerator pedal and replacement of any toyota all-weather floor mat. owners may contact toyota at 1-800-331-4331 or lexus at 1-800-255-3987.
Gulf states toyota IS recalling certain model year 2005-2010 vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold between september 1, 2005 and june 2, 2008 without the requisite load carrying capacity modification labels.
Risk and remedy
Risk
This does not meet the standard requirements.
Remedy
Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. Dealers will also correct the owner's manual. the safety recall began on may 27, 2010. owners may contact gulf states toyota at 713-580-3300.
Southeast toyota IS recalling certain model year 2005-2011 passenger vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold without the requisite load carrying capacity modification labels.
Risk and remedy
Risk
A driver may overload a vehicle which may increase the risk of a crash.
Remedy
Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. the safety recall began on may 27, 2010. owners may contact southeast toyota at 1-800-301-6859.
Toyota IS recalling certain model year 2005-2010 avalon, model year 2007-2010 camry, model year 2009-2010 corolla, corolla matrix, RAV4, model year 2010 highlander, model year 2008-2010 sequoia, and model year 2007-2010 tundra vehicles. due to the manner in which the friction lever interacts with the sliding surface of the accelerator pedal inside the…
Risk and remedy
Risk
The accelerator pedal may become hard to depress, slow to return to idle, or, in the worst case, mechanically stuck in a partially depressed position, increasing the risk of a crash.
Remedy
Dealers will install a reinforcement bar in the accelerator pedal which will allow the pedal to operate smoothly. gm will notify owners for the pontiac vibe please see 10v-018. this service will be performed free of charge. the safety recall IS expected to begin on february 5, 2010 and will be completed on march 15, 2010. owners may contact toyota at 1-800-331-4331.
Toyota IS recalling 27,080 model year 2005 through 2010 passenger cars built from september 1, 2005 to may 4, 2009. these vehicles were not equipped with load carrying capacity modification labels which fails to conform with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims."
Risk and remedy
Risk
Incorrect load carrying capacity modification labels could result in the vehicle being overloaded, increasing the risk of a crash.
Remedy
Toyota will notify owners and provide them with a new, accurate label to be installed over the inaccurate label free of charge. the safety recall began on august 18, 2009. owners may contact toyota at 1-888-270-9371.
Owner complaints
327 complaints52 involved a crash3 involved a fire16 injuries
What owners report most
Latest complaints
- Steering · Suspension · Wheels
We were informed of safety recalls for our Toyota Rav 4 2009 . We called the local Toyaota dealership for the recalls and was told on the phone after we dropped it off that they did the inspection to make sure the recalls could be completed and informed us that they could ,but they needed to keep…
We were informed of safety recalls for our Toyota Rav 4 2009 . We called the local Toyaota dealership for the recalls and was told on the phone after we dropped it off that they did the inspection to make sure the recalls could be completed and informed us that they could ,but they needed to keep overnight because they had to order the parts. Prior to dropping the vehicle off the car was able to be driven and no known issues were visible. Received call following told to come pick it up and that they officially refused to perform the recalls repairs. They stated that excessive structural damage and unsafe to drive to this degradation. Because the structural rust is directly in the exact suspension components targeted by this safety recalls. The vehicle cannot be remedied under standard recall procedures. By refusing the repair without providing an alternative solution The manufacture is failing its federal obligation to remedy a known safety defect. The vehicle is currently trapped in a regularity deadlock. It can not legally or safely be repaired. It is now deemed unsafe to be driven period. When the dealership gave the vehicle back, They wanted us to sign off and yes we refused because they told us it was inspected and was going to be repaired. When they did the inspection it is known that they have to bang , wrench and or pull on these parts to check to see if recall can be completed. Which they told us it could. When the vehicle was picked up we immediately noticed that the steering wheel was no longer in the correct position and that it was making an extreme screeching sound. We did not reach back out to the dealership as we feel they definitely caused more damage and already treated us poorly. We are requesting that the NHTSA intervenes to compel Toyota to provide an alternative remedy. Either structural vehicle replacement or a KB buyback to remove this 100% unsafe vehicle from the road. because the structural rust is directly impacting the exact components .
- Unknown or other
I am writing to report a suspected case of odometer fraud involving a vehicle currently listed for sale at Stacey’s Auto Sales, located at [XXX] . Vehicle Details: 2009 Toyota RAV4 Sport VIN: [XXX] Asking Price: $8,995 Current Listed Mileage: 108,540 I obtained an NMVTIS vehicle history report…
I am writing to report a suspected case of odometer fraud involving a vehicle currently listed for sale at Stacey’s Auto Sales, located at [XXX] . Vehicle Details: 2009 Toyota RAV4 Sport VIN: [XXX] Asking Price: $8,995 Current Listed Mileage: 108,540 I obtained an NMVTIS vehicle history report which shows this vehicle was listed at a dealer (Revolutionary Auto) in December 2020 with 150,439 miles on the odometer. The vehicle is currently being sold with only 108,540 miles — a discrepancy of approximately 42,000 miles over five years. The current Utah title lists odometer reading as ‘EXEMPT,’ which may have been used to obscure this discrepancy. I am not the buyer or seller of this vehicle. I am a private citizen who identified this discrepancy while researching the vehicle prior to a potential purchase. I am submitting this report in the interest of protecting other consumers. I have the NMVTIS report available as supporting documentation upon request. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Suspension
Repairs of the control arms indicated on recall NHTSA 16V-596 were never done on my vehicle after the recall was issued in 2016. Smart motors Toyota in Madison confirmed that the replacement of the control arms was never done on my vehicle, but they are showing no open recalls on my vehicle in…
Repairs of the control arms indicated on recall NHTSA 16V-596 were never done on my vehicle after the recall was issued in 2016. Smart motors Toyota in Madison confirmed that the replacement of the control arms was never done on my vehicle, but they are showing no open recalls on my vehicle in their system due to this being a re-recall. From what I've read many vehicles were incorrectly marked "complete" after the 2012 inspection, but the 2016 update (G0V) was issued specifically because those earlier inspections were found to be insufficient. I am entitled to this repair through Toyota due to this recall as Toyota has confirmed my vehicle was recalled and this repair was never completed. My rear control arms are showing signs of failure consistent with the re-recall.
- Engine
The contact owns a 2009 Toyota Rav4. The contact stated that there was an abnormal grinding sound coming from the engine at startup. There was no warning light illuminated. The vehicle was taken to an independent mechanic, and the contact was informed that the engine was consuming an excessive…
The contact owns a 2009 Toyota Rav4. The contact stated that there was an abnormal grinding sound coming from the engine at startup. There was no warning light illuminated. The vehicle was taken to an independent mechanic, and the contact was informed that the engine was consuming an excessive amount of engine oil caused by a gasket failure inside a piston in the engine. Due to the failure, the contact was frequently adding oil to the engine. The vehicle was taken to a dealer, and an estimate was provided for the repair. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 230,000.
- Engine
Engine timeing system rattle on startup. Even basic web research shows this is a common problem for select model years and acorss mulitple models. This issue has a high probility of causing catastrophic engine damage, where the timeing chain & VVT system fails to keep timing causing the valves to…
Engine timeing system rattle on startup. Even basic web research shows this is a common problem for select model years and acorss mulitple models. This issue has a high probility of causing catastrophic engine damage, where the timeing chain & VVT system fails to keep timing causing the valves to colide with the pistons. There is a TOTAL ENGINE FAILURE risk with each and every engine start. The fix on the 3.5L requires the engine to be removed, VVT and timing chain tensioner to be replaced. This is a $4000 to $5000 dollar repair. This is a clear manufacuting wide spread defect and should be repaired by toyota via recall!
- Unknown or other
I was hit with a rock right between my eyes while driving, took Toyota into shop they were surprised it had not fell in on my lap. Window frame has corroded, glass shop said the manufacturer did not paint were the seals meet around the window and has allowed moisture in and corroded the frame. I have 160,000 miles on a Toyota that the window could fail anytime.
- Structure › Body
We have a 09 Toyota Rav4 with a Blizzard Pearl paint that continues to fail. Apparently there were notices sent out in 2022 indicating a recall that would cover these repairs. We were unaware of these notices and continue to experience paint degradation on multiple areas of the car. I have…
We have a 09 Toyota Rav4 with a Blizzard Pearl paint that continues to fail. Apparently there were notices sent out in 2022 indicating a recall that would cover these repairs. We were unaware of these notices and continue to experience paint degradation on multiple areas of the car. I have contacted Toyota and they claim no responsibility past the 2022 expiration date. I am hoping that NTSB will reopen the recall regarding this issue. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Suspension
My son was looking to get his new tires aligned, and was informed by the mechanic that he would need to replace both side rear lower control arms, as Toyota had performed a safety recall GOV, resulting in the arms being epoxied, and therefore cannot be adjusted/ aligned. I contacted Toyota…
My son was looking to get his new tires aligned, and was informed by the mechanic that he would need to replace both side rear lower control arms, as Toyota had performed a safety recall GOV, resulting in the arms being epoxied, and therefore cannot be adjusted/ aligned. I contacted Toyota customer experience center (800 331 4331 - 1/16/2024) and she could not even call up the original recall. My question is: How can Toyota permanently remove a vehicle feature (adjustability of the suspension arms), and then require car owners to bear the brunt of re-installing the arms when you need to align your tires? This "solution" is totally unfair. I just purchased a new set of tires, and based on Toyota's "solution" I need to pay out of pocket to replace the control bars and/or damage my tires and have to replace them early. I was not able to find any other information on this issue on the web, and was wondering if Toyota had done anything to address this issue?
- Engine · Fuel/propulsion system · Vehicle speed control
Four incidents of unintended acceleration , in all instances foot was on break petal NOT on gas petal, 3 instances vehicle was stopped at traffic light, last incident was pulling into a parking space foot on brake, in all instances braked hard and shifted vehicle into neutral and turned vehicle off to avoid collisions, personal injury and property damage
- Power train · Suspension · Unknown or other
My rear passenger suspension has multiple part damage. Rear shock bracket failure and other parts.
- Structure › Body
paint recall the problem was confirmed twice by sansone dealership avenel, nj. 4/28/2021 and 12/1/2022. on both occasionspictures were submitted and i was told it would be taken care of. on 1/23/2023 i dropped car off to be repainted and was told it would be about 1.5 weeks. i picked up the car unrepaired on 2/21/2023. they said they would not honor recall
- Engine
Engine rattle on cold start ups.
- Service brakes
My car was being seviced today for rear brakes and the Toyota dealer needed to unseal previous safety recall in order to perform the service. I'm being charged to undo the recall to perform the service and then to reapply the recall. I do not understand how this cost is not the responsibility of…
My car was being seviced today for rear brakes and the Toyota dealer needed to unseal previous safety recall in order to perform the service. I'm being charged to undo the recall to perform the service and then to reapply the recall. I do not understand how this cost is not the responsibility of the manufacturer, Toyota. If there is a recall issued for an auto, shouldn't the recall correction allow for future auto maintenance where the recall doesn't need to undone and then reapplied?
- Suspension
The rear lower suspension arms recall notice solution was replacement of arms if needed and than sealed with epoxy. Labels were applied stating the arm is no longer adjustable. The vehicle no longer can routinely get a wheel alignment at a market expense. The Toyota company suggests for further…
The rear lower suspension arms recall notice solution was replacement of arms if needed and than sealed with epoxy. Labels were applied stating the arm is no longer adjustable. The vehicle no longer can routinely get a wheel alignment at a market expense. The Toyota company suggests for further alignments go to a Toyota dealership and have a alignment done for 900.00 dollars every time you need a alignment. This is not a safe solution. This only makes owners go to their dealerships and give them thousands of more dollars for taking away a routine adjustable maintenance capability with this permanent one time fix.
- Service brakes
My mother had the exact same issue reported in Toyota Manufacturer case 1707311582 and NHTSA report 11396355 from Feb 15, 2021. My mother had not reported to me, until it happened while I was driving her around Dec. 24, 2021, that her Rav. rev'd and accelerated when she applied the brake while…
My mother had the exact same issue reported in Toyota Manufacturer case 1707311582 and NHTSA report 11396355 from Feb 15, 2021. My mother had not reported to me, until it happened while I was driving her around Dec. 24, 2021, that her Rav. rev'd and accelerated when she applied the brake while leaving a parking spot. Here's what I've reported to my Toyota dealership where we bought the vehicle. Until last month (Nov. 21), the vehicle had an immaculate operation and maintenance record. To the repair shop "Twice in the past month, we've had brake failure, accelerator failure issues. The first time, my mother was pulling forward at less than 5 miles per hour in a parking lot. She pushed the brake pedal when pulling forward, but the car did not slow, the brakes did not engage, and instead, the RAV revved and accelerated forward. She crashed into the parked vehicle and incurred damages that already have been fixed by USAA at a service location in Richmond. The airbag did not deploy. Dec. 24, here in Churchland, I was driving with her. While coasting to a stop light at less than 10 miles per hour, I attempted to stop by pressing the brake. The car revved and accelerated to the light, I pressed both feet again, and the car continued to accelerate and I ended up running a red light and luckily we did not have an accident or cause the person behind us to rear end us. It was not until after my driving on Dec. 24 that my Mom told me she had an accident a month earlier and it was because she couldn't get the car to stop. She assumed it was her. The vehicle has almost 90k miles. Looking for recalls, because this is not normal for brakes to malfunction this way, I found a consumer article describing to my Mom's and my description to almost exact detail captured in Manufacturer case number provided above. That vehicle had approximately 77k miles. I will be contacting USAA to report the issue, this is clearly a safety issue."
- Structure › Body
The paint on my white 2009 Toyota RAV4 has been coming off. Sheets of color is peeling on the roof. I have several large (1-2 inches) bare spots on the top and many tiny ones on the body hood and doors, rusting for years. The manager of Titus-Will Toyota advised me not to do anything about it when…
The paint on my white 2009 Toyota RAV4 has been coming off. Sheets of color is peeling on the roof. I have several large (1-2 inches) bare spots on the top and many tiny ones on the body hood and doors, rusting for years. The manager of Titus-Will Toyota advised me not to do anything about it when I showed them the recall letter from Toyota and let him take pictures of the affected areas of my car. He said he would send a request and let me know about the repair decision. It has been more than two years since my complaint. I ask about it almost every time I go there for my scheduled service maintenance, and I get no answer so far. Until now, I still don’t have a response from them, and I am a little unhappy. Also, I see that I am not their favorite customer and avoided by management as they are always swamping. I showed them how bad the paint continues to come off, and the rust is awful. I could off taken care of it by now, but the manager clearly said not to paint it or do anything about it until he gets confirmation about the issue. My roof could start licking with all this rain and rust. Thank you.
- Suspension
My problem IS upon inspection of the vehicle I was told a recall (16v596000) for my rear suspension arms was available and I needed to have it done as the back end nuts couldn't be adjusted. I called a dealership and was told this was taken care of 3 years ago, yet the problem still remains.
- Engine · Service brakes · Vehicle speed control
While decelerating on a freeway off-ramp at approx. 25 mph, the brakes failed to stop the car. Going no more than 5 mph, I lifted off slightly then depressed them all the way to the floor; they didn't engage properly but finally slowed the car almost to a complete stop, but the engine revved and the car kept wanting to go forward. I threw the transmission into park and turned off the ignition.
- Structure › Body
The paint on our 2009 toyota RAV4 comes of with the slightest bump from something like a branch, which should not normally cause paint to come off. Because of this we have several bare spots which are beginning to rust.
- Engine
I took my car in for service on october 12, 2020 because the oil light was flickering though I am not due for another oil change until january. I was told to replace the motor due to excessive oil consumption. upon researching online learned that this IS due to defective piston rings and in…
I took my car in for service on october 12, 2020 because the oil light was flickering though I am not due for another oil change until january. I was told to replace the motor due to excessive oil consumption. upon researching online learned that this IS due to defective piston rings and in 2011, toyota issued a technical service bulletin. at this point, they are refusing to correct the error with the design of the pistons.
- Structure › Body
Sheets of the paint started to come off while going down the highway.
- Engine
All lights come on check engine,4wd,trac , come and goes, going 6 times already to dealer last 2 weeks.. RAV4 with low miles .. Toyota very dissatisfied
- Power train
When the vehicle travels above 25 mph, a loud whining noise can be heard from the rear-center of the vehicle. The noise progressively increases in volume as the vehicle increases its speed. Once the vehicle travels fast enough, or enough power IS fed through, power of the vehicle can be affected. *tr
- Unknown or other
Whining noise from rear and continues to get loud while driven. Was told it may be my rear differential that was identified by toyota in 2013
- Electrical system · Steering · Visibility/wiper
The power steering light came on then the steering wheel locked I jerked it to the right to get it to pull off the road. I was driving on a city street going up hill when the car finally disabled, the mechanic told me he found nothing wrong when he put it on the diagnostic I don't feel safe driving the car with my child I've paid 140.00 for and inspection now I'm taking it to the sf toyota mechanic.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Power Window Master Switch Fire
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia…
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
- Power Window Master Switch Fire
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built…
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
- Unintended and Uncontrolled Acceleration
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested…
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005119This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005061This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
- 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
- 10230369DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10230368DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement.
- 10230367DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10227898TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10220174TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
- 10220158DL: Toyota has received reports of paint peeling on certain vehicles with the original factory-applied Blizzard Pearl or Super White paint colors. These reports indicate that vehicles with these specific paint colors, applied during the vehicle manufacturing process, may experience paint peeling on exterior metal body panels. Although the original factory paint is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to the condition described above. The following information is provided to inform you and your staff of the program notification schedule and your degree of involvement
- 10214323TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
- 10211826CSP: Customer Support Program ZKG - Paint Repair Process Operation Flow Chart
- 10210375TSB: This Service Bulletin includes procedures to replace damaged or loose front carpet floor retainer(s) without replacing the carpet assembly. Follow the Repair Procedure in this bulletin to replace the loose or damaged carpet floor retainer(s).
- 10207946POL: This consolidated Tire Warranty Guide contains the complete warranty terms for all brands of ground and spare tires currently in use by Toyota. This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.
- 10204571TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10204546DL: CUSTOMER SUPPORT PROGRAM ZKG Multiple Models and Model Years Vehicles Painted with Blizzard Pearl (070) or Super White (040) Paint Color Coverage for Peeling of Factory-Applied Paint
- 10203532TT: Some customers may encounter Bluetooth connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
- 10201400TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
- 10197494Technician Certification Requirements.
- 10197476Replacement vin plates.
Every Toyota RAV4 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.