2014 Toyota Sienna
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › Sienna › 2014
These records cover every 2014 Toyota Sienna. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
6 recalls name the 2014 Toyota Sienna. Newest first.
Vantage Mobility International, LLC (Vantage) is recalling certain 2012-2018 AMS Genesis wheelchair vans, built on a Toyota Sienna vehicles. The rubber brake hoses that attach to the rear wheel assembly may be too short, causing them to rub against the rear axle trailing arm.
Risk and remedy
Risk
The contact may cause failure of the rear brake hoses, resulting in a loss of vehicle control and reduced braking ability, increasing the risk of a crash.
Remedy
Vantage will notify owners, and dealers will install a set of rear brake hoses that will provide the proper clearance, free of charge. The recall began December 16, 2019. Owners may contact Vantage customer service at 1-800-488-9082.
Braun Corporation (Braun) is recalling certain 2014-2019 Toyota Sienna mobility van conversions. The brake lines may have incorrect tube nut fittings installed, which may cause a pressure drop within the braking system.
Risk and remedy
Risk
The reduction in the braking system pressure may cause a loss of braking power in the rear braking system, increasing the risk of crash.
Remedy
Braun has notified owners, and dealers will install an adaptor to correct the issue, free of charge. The recall began June 25, 2019. Owners may contact Braun customer service at 1-800-488-0359.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2014-2016 Toyota 4Runner, 2014-2015 Scion xB, Lexus IS350C, IS250C, 2014 Toyota Sienna, Lexus IS-F, and 2014-2017 Lexus GX460 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
Toyota will notify owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began February 15, 2019. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2011-2016 Toyota Sienna minivans manufactured January 4, 2010, to August 12, 2016. If the power sliding door is unable to be opened when commanded, such as if the door is frozen shut, the door may subsequently open unexpectedly, possibly while the vehicle is moving.
Risk and remedy
Risk
If door opens while the vehicle is moving, there would be an increased risk of injury to the vehicle occupants.
Remedy
Toyota will notify owners, and dealers will replace the junction block, rear sliding door wire harnesses, and install two sub wire harnesses, free of charge. The recall began on July 28, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G04.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2014 Toyota Avalon, Camry, Sienna, and Highlander and model year 2015 Lexus RX350 vehicles. Fuel may leak from the one of the fuel delivery pipes in the engine compartment.
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy
Toyota will notify owners, and dealers will replace any of the suspect fuel delivery pipes free of charge. The recall began November 17, 2014. Owners may contact Toyota customer service at 1-800-331-4331.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2014 Sienna vehicles manufactured June 17, 2014, through June 24, 2014. The affected vehicles have a transmission shift control cable whose protective cable sleeve may have been damaged during assembly. This could cause the control cable to bind or separate during gear shift…
Risk and remedy
Risk
If the transmission shift cable separates while the vehicle is being driven, the transmission gear selection may not match the indicated gear and the vehicle may move in an unintended or unexpected direction, increasing the risk of a crash. Furthermore, when the driver goes to stop and park the vehicle, despite selecting the 'PARK' position, the transmission may not be in 'PARK.' If the vehicle is not in the 'PARK' position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy
Toyota will notify owners, and dealers will inspect and replace the transmission shift control cable, as necessary, free of charge. The recall began in early August 2014. Owners may contact Toyota customer service at 1-800-331-4331.
Owner complaints
163 complaints6 involved a crash2 involved a fire3 injuries
What owners report most
Latest complaints
- Fuel/propulsion system
The fuel lines that are connected to recall 14V576000 need to be replaced and so that recall needs to be expanded as the parts are present in my vehicle but the connected to my VIN
- Electrical system · Engine · Fuel/propulsion system
Sluggish start when hot - fuel pump leak into engine when hot, causing starter issues, wears out starter, causes other stress on engine. Common issue in Toyota Siennas. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Vehicle speed control
The contact owns a 2014 Toyota Sienna. The contact stated that while driving at various speeds the vehicle had experienced unintended acceleration. During the failure the driver forcely pressed the brake pedal to stop the vehicle. The contact indicated that the failure had once occurred while a…
The contact owns a 2014 Toyota Sienna. The contact stated that while driving at various speeds the vehicle had experienced unintended acceleration. During the failure the driver forcely pressed the brake pedal to stop the vehicle. The contact indicated that the failure had once occurred while a transporting a Uber passenger. The cause of the failure was not determined. The manufacturer and local dealer were not contacted. The failure mileage was 120,000.
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2014 Toyota Sienna. The contact discovered a mileage discrepancy after the purchase. The vehicle was a private sale. At the time of the purchase, the mileage was 59,500. It was later discovered upon checking the paperwork that the mileage was 176,047.
- Fuel/propulsion system
The vehicle died while driving and when I try to start again it will crank but can't start.
- Air bags
Dear sir/ madam, I am writing to report an issue with recall status reporting. All open recalls for my vehicle (VIN: [XXX] ) were completed at an authorized dealership on [01/27/2026]. I have documentation from the dealer confirming that the recall repairs were successfully performed. However…
Dear sir/ madam, I am writing to report an issue with recall status reporting. All open recalls for my vehicle (VIN: [XXX] ) were completed at an authorized dealership on [01/27/2026]. I have documentation from the dealer confirming that the recall repairs were successfully performed. However, the recall status has not been updated in the NHTSA database and still appears as “open.” I request assistance in ensuring the recall completion is properly reported and reflected in the NHTSA system. Thank you. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Structure › Body
The passenger-side power sliding door system failed to stop or reverse when it encountered physical interference with the vehicle’s open fuel door. The door continued opening under power despite clear obstruction by a fixed exterior body component. The affected components, including the sliding…
The passenger-side power sliding door system failed to stop or reverse when it encountered physical interference with the vehicle’s open fuel door. The door continued opening under power despite clear obstruction by a fixed exterior body component. The affected components, including the sliding door mechanism and damaged fuel door latch, remain available for inspection upon request. A powered sliding door continuing to operate against an obstruction creates a foreseeable risk of injury to occupants or bystanders, as well as vehicle damage. If a person’s hand, arm, or clothing had been in the same position as the fuel door, injury could have occurred. The incident occurred during normal vehicle use and demonstrates inadequate safeguards against obstruction. The issue has been formally reproduced or confirmed by an independent service center which noted that the incident occurred as described during normal operation of the power sliding door, and no abnormal conditions were present at the time. No warning lamps, messages, or other symptoms appeared prior to the incident. The power sliding door operated normally and without indication of malfunction until it failed to stop when encountering the open fuel door. Fueling the vehicle with the fuel door open is routine and expected vehicle use. The absence of any interlock, sensor logic, or safeguard preventing a powered sliding door from operating against an open body panel represents a design deficiency rather than a maintenance or wear issue. This condition may affect other vehicles equipped with similar power sliding door systems and warrants evaluation.
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2014 Toyota Sienna. The contact stated that upon taking the vehicle to a dealer for an oil change, it was discovered through the Carfax report that there was a mileage discrepancy. The vehicle was a private sale through Facebook Market Place. At the time of…
Odometer Fraud. The contact purchased a 2014 Toyota Sienna. The contact stated that upon taking the vehicle to a dealer for an oil change, it was discovered through the Carfax report that there was a mileage discrepancy. The vehicle was a private sale through Facebook Market Place. At the time of purchase, the vehicle mileage was 146,000, but upon retrieving the Carfax report, the contact discovered that the mileage was 187,391 on the State inspection report dated June 18, 2025. The issue had not been reported to another agency.
- Engine · Structure
The contact owns a 2014 Toyota Sienna. The contact stated that while driving 70 MPH, there was an audible alarm coming from the vehicle, alerting the contact that the door was ajar. The passenger’s side slide door opened independently while the vehicle was in motion. The vehicle was modified to…
The contact owns a 2014 Toyota Sienna. The contact stated that while driving 70 MPH, there was an audible alarm coming from the vehicle, alerting the contact that the door was ajar. The passenger’s side slide door opened independently while the vehicle was in motion. The vehicle was modified to accommodate a ramp for the contact's two wheel-bound children. The contact pulled over to the side of the road and closed the sliding door. The contact's husband tied the door to prevent it from opening independently again. The check engine warning light was intermittently illuminated. The vehicle was taken to the dealer, where it was inspected. The contact was informed that two latches had corroded and needed to be replaced. The vehicle was not repaired. Upon further investigation, the contact related the failure to NHTSA Campaign Number: 16V858000 (STRUCTURE). However, the VIN was not included. The manufacturer was not made aware of the failure. The failure mileage was approximately 99,500.
- Latches/locks/linkages › Doors › Latch
The passenger side cable that opens and closes the door snapped and is disconnected. The door will get stuck in an open or closed position.
- Latches/locks/linkages
The contact owns a 2014 Toyota Sienna. The contact stated that while opening the driver’s side sliding door, the drive belt snapped. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the sliding door drive belt. The vehicle was not…
The contact owns a 2014 Toyota Sienna. The contact stated that while opening the driver’s side sliding door, the drive belt snapped. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the sliding door drive belt. The vehicle was not repaired. The contact also stated that the same failure later occurred on the passenger’s side sliding door. The manufacturer was not notified of the failure. The failure mileage was 155,000.
- Engine
Timing chain cover leaking oil. This is known issue on 3.5L V6 model years 2011 -2022
- Electrical system · Latches/locks/linkages › Doors › Latch
The contact owns a 2014 Toyota Sienna. The contact stated that the passenger's side and driver's side sliding doors were locked and had failed to open automatically and manually. The contact stated that the motors of the doors were previously replaced; however, the failure persisted. The vehicle…
The contact owns a 2014 Toyota Sienna. The contact stated that the passenger's side and driver's side sliding doors were locked and had failed to open automatically and manually. The contact stated that the motors of the doors were previously replaced; however, the failure persisted. The vehicle was taken to the local dealer, where the doors could not be opened. The dealer determined that the Power Sliding Door Cable Sub-Assembly, the Sliding Door Center Hinge Assembly, the Fuel Filler Door Hinge and Pin, the Power Sliding Door Rear Lock Assembly, the Sliding Door Front Lock Assembly, and an unknown part had failed and needed to be replaced. The dealer related the failure to Toyota Campaign Number: ZK1. The manufacturer was notified of the failure and informed the contact that the vehicle was no longer covered because the campaign had expired. The vehicle was not repaired. The failure mileage was approximately 100,000.
- Engine
I have 2014 Toyota sienna head gasket problem with less than 100,000 k
- Unknown or other
The driver's side passenger door power cable broke. We had to turn off the power to all of the mechanical doors. There may have been a recall on this awhile back. The cable could be seen outside of the vehicle. We since have tucked it out of the way.
- Structure
The contact owns a 2014 Toyota Sienna. The contact stated while driving at various speeds, the contact heard abnormal sounds coming from the vehicle. The passenger’s side slide door became inoperable. No warning light was illuminated. The vehicle had not been diagnosed or repaired by an independent…
The contact owns a 2014 Toyota Sienna. The contact stated while driving at various speeds, the contact heard abnormal sounds coming from the vehicle. The passenger’s side slide door became inoperable. No warning light was illuminated. The vehicle had not been diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and advised the contact to call the NHTSA Hotline for assistance. The failure mileage was approximately 68,000.
- Unknown or other
The spare tire, which is normally secured under the minivan, fell off while driving at approximately 40 mph. My son, who was driving the vehicle, heard a sudden loud noise from the underside of the vehicle. He looked in his rearview mirror and saw something in the middle of the road. He pulled…
The spare tire, which is normally secured under the minivan, fell off while driving at approximately 40 mph. My son, who was driving the vehicle, heard a sudden loud noise from the underside of the vehicle. He looked in his rearview mirror and saw something in the middle of the road. He pulled over to inspect the vehicle, and noticed that the spare tire was gone, which he was able to retrieve. I brought the vehicle to a local Toyota dealer, who indicated I needed a new spare tire carrier (at a cost of $329.07), since the original unit had failed due to rust. The spare tire had never been used or removed from its manufactured mounting position since original purchase of the vehicle in 2014. There were no warning signs at any time prior to the incident that the spare tire might come loose from its mounted position. The safety issues associated with this incident are obvious, e.g., another vehicle striking the spare tire or loosing control to avoid the spare tire; the tire rolling and striking a person, another vehicle, or damaging property, etc.
- Steering
I had the vehicle inspected by personal mechanic because the steering wheel would tighten and then release whenever turned to right and release on left turn. this would happen on a regular basis when turning the wheel. The mechanic did recommend that I called the manufacturer to check if there was…
I had the vehicle inspected by personal mechanic because the steering wheel would tighten and then release whenever turned to right and release on left turn. this would happen on a regular basis when turning the wheel. The mechanic did recommend that I called the manufacturer to check if there was any recall for the problem. Which I did. Respond was no and so I explained the problem to the representative. There IS not a failure or incident except the steering wheel keeps on tightening and I'm just being cautious. No manufacturer, police, or insurance has inspected it because there IS no accident. Thank god! Just concerned because my mechanic said it IS something for the dealership. Something to do possibly within the steering column/channel component. Not sure which IS right, but to check for recall by manufacturer. I took it to tire kingdom but something else was repaired. So I'm still having trouble with steering wheel stiff tightening up lightly. I would feel it tighten whenever driving 45 miles or more.
- Seat belts
After a rain, water will leak into the driver and front passenger seatbelt coil housing. The front passenger seatbelt was not used in some time and mold developed with green and black stains all along the seatbelt. After it rained, the driver side seatbelt released about 1 cup of water when I…
After a rain, water will leak into the driver and front passenger seatbelt coil housing. The front passenger seatbelt was not used in some time and mold developed with green and black stains all along the seatbelt. After it rained, the driver side seatbelt released about 1 cup of water when I pulled the seatbelt. With my wife as the passenger, she was conflicted about wearing the seatbelt while having mold pressed against her body, clothes, and breathing it in. The smell of mold is now present in the vehicle. This problem has been reproduced via online reports at SiennaChat.com. No warning lamps, messages or symptoms appeared prior, or during, this issue. I am in the process of reporting it to Toyota as soon as the next business day (Monday).
- Wheels
Tire pressure monitor system dashboard icon is ridiculously non-intuitive. Both my wife and daughter have been baffled by it because the icon DOES NOT LOOK LIKE A TIRE! Neither are stupid, one is a college grad and the other is a junior at ASU. The icon is a cross-section of a tire, and none of…
Tire pressure monitor system dashboard icon is ridiculously non-intuitive. Both my wife and daughter have been baffled by it because the icon DOES NOT LOOK LIKE A TIRE! Neither are stupid, one is a college grad and the other is a junior at ASU. The icon is a cross-section of a tire, and none of them know what a tire cross-section looks like. Because of this, they have driven on dangerously under inflated tires without knowing it. Fix the icon SO IT LOOKS LIKE A TIRE! Thank you.
- Suspension · Wheels
The van seems to prematurely wear tires out before their service life expectancy. I've owned the van for seven years, and I've had to purchase over five complete sets of tires. The front tires wear-out much faster than the rear tires, and do not last more than 15K miles. I've had several…
The van seems to prematurely wear tires out before their service life expectancy. I've owned the van for seven years, and I've had to purchase over five complete sets of tires. The front tires wear-out much faster than the rear tires, and do not last more than 15K miles. I've had several alignment jobs done, both (L&R) control arms replaced, ball joints, and struts - the van still wears out tires regardless of tire brand. I suspect the must be a design flaw causing premature wear and tear on tires on the front of the van, as I just replaced another set of tires from the Yokohama brand recommended for the van. I've asked Toyota, and they claim ignorance of such a problem. It is my desire to make this problem known, and to have the Government investigate if there is an design flaw in the Sienna van which is causing rapid part failures.
- Lane departure › Blind spot detection · Service brakes · Structure › Body
Great coaching
- Forward collision avoidance › Automatic emergency braking · Service brakes · Structure › Body
Good question
- Traction control system · Vehicle speed control › Accelerator pedal
The contact owns a 2014 Toyota Sienna. The contact stated while attempting to drive there was an idling issue while attempting to make a turn while accelerating. There was no warning light illuminated. The contact also stated that there was a traction control failure. Additionally, the vehicle…
The contact owns a 2014 Toyota Sienna. The contact stated while attempting to drive there was an idling issue while attempting to make a turn while accelerating. There was no warning light illuminated. The contact also stated that there was a traction control failure. Additionally, the vehicle failed to accelerate while entering the highway. The failure had been consistent for several years. The vehicle was taken to the dealer to be diagnosed; however, the mechanic was unable to replicate the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 94,000.
- Suspension
The rear electro magnetic coupler had to be replaced at 120000 miles. Online multiple complaints are listed for the same issue and Toyota has a recall issues for the same component for the RAV4. So why not for the Toyota Sienna xle ltd awd Thanks
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005119This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005061This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
- 10244115TSB: The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. Follow the procedures outlined in this service bulletin to aid in locating, inspecting, and repairing refrigerant leaks
- 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
- 10227898TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10224108TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
- 10220183TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
- 10220174TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process
- 10217806CSP: Takata CSP Coverage Job Aid - published 7.28.2022
- 10217804CSP: On July 30, 2018, a settlement of claims for Economic Loss related to Takata airbag inflators was approved for full implementation. The settlement includes Toyota?s agreement to provide a Customer Support Program (?CSP?) for 2002-2019 model year (MY) vehicles originally equipped with certain Takata airbag inflators or repaired under a recall with Takata airbag inflators to provide coverage for repairs of the airbag inflator contained in the airbag module. This CSP letter is to help clarify how to administer this coverage in accordance with the settlement. This is NOT a recall or a campaign, but is provided to reassure owners that Toyota stands behind the reliability of our vehicles.
- 10214323TT: Some Toyota vehicles installed with Toyota Complete Maintenance Care (TCMC) brake pads may exhibit a groan or squeak noise in various driving conditions
- 10208995TSB: Some 2010 ? 2022 model year Toyota vehicles may exhibit paint stains after the removal of Rapgard?. The paint stains may appear to be under the clear coat but are usually under wrinkles in the Rapgard?. The wrinkles may trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces such as the hood, roof, and trunk. Follow the Repair Procedure in this bulletin to address this condition
- 10207946POL: This consolidated Tire Warranty Guide contains the complete warranty terms for all brands of ground and spare tires currently in use by Toyota. This information must be kept near the point of vehicle sale and be available to any customer that requests it. Customers can find this information on the Owner?s section of Toyota.com. Dealers can locate a copy of this guide on the Claims Processing & Resource Center in Dealer Daily as well.
- 10204571TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10203533TSB: For proper calibration of the millimeter wave radar sensor, the vehicle and radar target must be on a level surface with a consistent plane. If a level surface with a consistent plane is not available, use the Floor Slope Compensation Procedure in this service bulletin in conjunction with the appropriate model and model year Repair Manual instructions when adjusting the millimeter wave radar sensor.
- 10203532TT: Some customers may encounter Bluetooth connectivity concerns such as: ?Difficulty to pair the phone. ?Intermittent Bluetooth failure to connect to the vehicle when first turning on the vehicle. ?Various Bluetooth Audio functions are no longer functioning with customer?s phone such as ability to change the track using the steering wheel controls. These concerns can be caused by changes made on the customer?s phone. Make sure to inquire with the customer if the connectivity concerns occurred after receiving an operating system update on their phone, or if they have restored their phone data/settings recently.
- 10201400TSB: Some 2006 ? 2022 model year Toyota vehicles in particular geographic areas may exhibit a condition where the HVAC evaporator drain hose has become obstructed with an insect nest. An insect repellent drain hose tip (ARINIX Tip) is available to help minimize future occurrences of this environmental condition. For some models, a new drain hose is required to properly fit the ARINIX Tip. Follow the procedures in this bulletin for proper handling and installation of this optional service part.
- 10201352TT: Some 2014-2021 model year vehicles equipped with Dynamic Torque Control AWD system may experience a ?Noise? or ?Abnormal Operation? condition from the rear differential front coupling. In some cases, even an ?AWD System Message? with or without a DTC may be present with or without other conditions present.
- 10198150Updates to the 2014-2021 toyota universal flat rate manual
Every Toyota Sienna model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.