2016 GMC Yukon
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2016 GMC Yukon. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2016 GMC Yukon. Newest first.
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic…
Risk and remedy
Risk
Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy
GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Risk and remedy
Risk
As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy
GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL…
Risk and remedy
Risk
A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy
GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and…
Risk and remedy
Risk
A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy
GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
General Motors LLC (GM) is recalling certain model year 2016-2017 Chevrolet Silverado 1500 and 2016 Cadillac Escalade, Cadillac Escalade ESV, Chevrolet Suburban, Chevrolet Tahoe, GMC Sierra, GMC Yukon and GMC Yukon XL vehicles. The front upper control arms may have inadequate welds near the control arm bushing.
Risk and remedy
Risk
Inadequate welds may allow the control arm to separate from the bushing, compromising steering and increasing the risk of a crash.
Remedy
GM will notify owners, and dealers will replace the left and right front upper control arms and realign the vehicle, free of charge. The recall began on May 18, 2016. Until the repairs have been made, owners are advised not to drive their vehicles. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, or GMC customer service at 1-800-462-8782. GM's number for this recall is 42190.
Owner complaints
271 complaints4 involved a crash5 injuries
What owners report most
Latest complaints
- Seat belts
The cable that attaches at the base of the seat sheared off making the anchor point useless
- Power train
The contact owns a 2016 GMC Yukon. The contact stated that upon starting the vehicle, the vehicle was shaking violently. The contact stated that while driving 15 MPH, the vehicle lost automotive power. The check engine warning light was illuminated. The contact continued driving at a reduced speed.…
The contact owns a 2016 GMC Yukon. The contact stated that upon starting the vehicle, the vehicle was shaking violently. The contact stated that while driving 15 MPH, the vehicle lost automotive power. The check engine warning light was illuminated. The contact continued driving at a reduced speed. The vehicle was taken to a dealer where it was diagnosed, and the contact was informed that the camshaft lobe had failed and needed to be replaced. The manufacturer was notified of the failure. The failure mileage was 115,280.
- Service brakes
Abs system is not functioning properly, codes are being thrown for multiple things such as cylinder 2, which all spark plugs and coils and spark lines were fixed, then it ran for one day and threw a different code of cylinder 6 misfire with the abs and stailitrx system not functioning correctly.…
Abs system is not functioning properly, codes are being thrown for multiple things such as cylinder 2, which all spark plugs and coils and spark lines were fixed, then it ran for one day and threw a different code of cylinder 6 misfire with the abs and stailitrx system not functioning correctly. Several parts have been changed on this by professionals and they can’t figure out why this is happening. I don’t have my full hp.
- Power train
Issues with the 8L90 transmission. The shuddering and hesitation has gotten very bad and having to look into options to repair or replace the transmission
- Engine
The car lost all engine power on the interstate of I10. Leaving me without power, barely able to get to the side of the road. Warning only when lost engine power on the highway. Cannot be driven.
- Service brakes, hydraulic
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that there was an abnormal sound coming from the vehicle and the ABS warning light was illuminated.…
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that there was an abnormal sound coming from the vehicle and the ABS warning light was illuminated. The contact stated that after several attempts, the vehicle stopped. The vehicle was taken to the dealer; however, the vehicle was waiting to be inspected. The contact stated that an unknown recall repair with a similar description was completed in 2024; however, the contact was informed that the repair was not covered under warranty. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 136,000.
- Steering
Power steering intermittently and unexpectedly stops working.
- Power train
The contact owns a 2016 GMC Yukon. The contact stated that while the vehicle was at the inspection station for an inspection, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that the transmission had seized, and the vehicle failed to…
The contact owns a 2016 GMC Yukon. The contact stated that while the vehicle was at the inspection station for an inspection, the accelerator pedal was depressed; however, the vehicle failed to accelerate as intended. The contact stated that the transmission had seized, and the vehicle failed to move. In addition, the check engine warning light was illuminated. The contact stated that the failure had occurred immediately after an unknown device was attached to the vehicle while being inspected. The contact informed the inspector of the failure. The contact was advised to contact the NHTSA Hotline to report the failure. The dealer was not made aware of the failure. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The manufacturer was not made aware of the failure. The failure mileage was 119,637.
- Service brakes, hydraulic
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the brake pedal became inoperable and failed to engage properly, with no warning lights illuminated. The contact also stated that while the vehicle was parked, excessive force was needed to engage the…
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the brake pedal became inoperable and failed to engage properly, with no warning lights illuminated. The contact also stated that while the vehicle was parked, excessive force was needed to engage the brake pedal and stop the vehicle. The contact stated that the failure nearly caused the vehicle to collide with another object. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 108,959.
- Electrical system · Power train · Unknown or other
Transmission went out very early. Had to get it replaced whenever I reverse. I have to really smash on the break in order for it to stop if it does stop so somethings wrong with the breaking whenever I hit a bump the left side suspension feels like I’m a lose control and sometimes my radio works…
Transmission went out very early. Had to get it replaced whenever I reverse. I have to really smash on the break in order for it to stop if it does stop so somethings wrong with the breaking whenever I hit a bump the left side suspension feels like I’m a lose control and sometimes my radio works and sometimes it doesn’t I’ve been trying to work with dealers I have extended warranty on it. They’re saying it’s not covered something about the brake pump is covered, but the belts are not. The transmission was put in only because it left me stranded. Otherwise I would’ve been stuck paying for that. The dealership actually helped me with that. My GPS turns on and off sometime. I’m not sure if it’s electrical
- Engine · Fuel/propulsion system
Ticking sound coming from engine, possible damaged camshaft lobe due to lifter roller failure. It can cause sudden engine failure, significant power loss, and unexpected stalling while driving, increasing crash risks. The issue is linked to AFM (Active Fuel Management) system failures. The problem has been diagnosed by dealer service department. No warning lamp or message, problem first appeared 7 April 2026.
- Suspension
Vehicle been in the shop 3 times. [XXX] suspension light repeat come on. Working with warranty company. Light came on again 3 more times after Vehicle left the shop INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Suspension
The suspension service lights repeatedly coming on.
- Engine
The contact owns a 2016 GMC Yukon. The contact stated that the vehicle was initially repaired under warranty for a bent push rod in cylinder #4; however, the failure recurred. The vehicle was repaired another time at the expense of the contact's son, who previously owned the vehicle; however, the…
The contact owns a 2016 GMC Yukon. The contact stated that the vehicle was initially repaired under warranty for a bent push rod in cylinder #4; however, the failure recurred. The vehicle was repaired another time at the expense of the contact's son, who previously owned the vehicle; however, the failure persisted. The contact stated that while idling and while driving, the engine was misfiring and running rough. Additionally, there was a significant amount of smoke coming from the exhaust pipe. The check engine warning light was illuminated. The vehicle was taken back to the dealer, where it was diagnosed, and the dealer determined that the engine needed to be replaced. The vehicle was not repaired due to the cost. The manufacturer was contacted and informed that the repair would not be covered because the vehicle was out of warranty. The failure mileage was approximately 27,000.
- Engine · Fuel/propulsion system
Misfire then replaced plugs,coils and wires, then change fuel injector, and problem still there, then started truck and was tossing power and motor started ticking. Every shop told me this is the same common problem they're having with all 6.2L engine and they're all on recall by GM. I know 2016 are not in recall but I think they should be because this problem is in all 6.2L engine
- Steering
When making a slow turn in drive or reverse the park assist screen shows it’s not working. Then all screens in the car turn black and the steering locks while driving. Making it impossible to turn or move. This is happening while driving, while parking. Putting my safety and others at risk due to…
When making a slow turn in drive or reverse the park assist screen shows it’s not working. Then all screens in the car turn black and the steering locks while driving. Making it impossible to turn or move. This is happening while driving, while parking. Putting my safety and others at risk due to not being able to control the steering. Park assist failure screen pops up then all screens turn black. Car is still on just unable to move. I have not had it checked by a mechanic yet.
- Engine
On [XXX], while idling in my driveway the engine abruptly stopped with a loud clunk and refused to turn over when I attempted to restart it. The vehicle was towed to Bergstrom GMC in Appleton WI. Upon inspection it was determined that a connecting rod and crankshaft bearing had failed requiring…
On [XXX], while idling in my driveway the engine abruptly stopped with a loud clunk and refused to turn over when I attempted to restart it. The vehicle was towed to Bergstrom GMC in Appleton WI. Upon inspection it was determined that a connecting rod and crankshaft bearing had failed requiring replacement of the engine. The vehicle has a 6.2-litre V-8 engine with 106,000 miles on it. The vehicle is currently still at the dealership waiting for the engine replacement at an estimated cost of $18,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Fuel/propulsion system
THE fuel pressure line from the fuel pump to the flex fuel sensor chaffed a pin hole leak near the front top of the fuel tank. This caused a significant fuel smell and trace leak at the front of the fuel tank which could lead to a fire or explosion. The new hose has a longer chaffing covering…
THE fuel pressure line from the fuel pump to the flex fuel sensor chaffed a pin hole leak near the front top of the fuel tank. This caused a significant fuel smell and trace leak at the front of the fuel tank which could lead to a fire or explosion. The new hose has a longer chaffing covering leading me to believe gm knew about this issue. vehicle has 127,000 miles. I feel gm should reimburse me for this repair as a fuel line should not have ever chaffed through and leaked.
- Exterior lighting · Lane departure › Blind spot detection · Lane departure › Warning
The LED left turn signal and blind spot detection ( safety feature) on the left outside rear view mirror suddenly stopped working. The is a TSB for warranty for 2016-2018 GM YUKON (#10-08-64-002D) and it states that the bulletin has been revised to include 2016-2018 year models for this defect. I…
The LED left turn signal and blind spot detection ( safety feature) on the left outside rear view mirror suddenly stopped working. The is a TSB for warranty for 2016-2018 GM YUKON (#10-08-64-002D) and it states that the bulletin has been revised to include 2016-2018 year models for this defect. I am starting this claim because I am told by GM that my VIN is not covered under this warranty, yet I am experiencing the same issue stated in the TSB listed above.
- Electrical system · Engine
A side detection module pin was corroded and was disrupting the electrical signals to major vehicle components, such as the dash (DIC). The DIC would lose communication with the rest of the vehicle while driving so no vehicle operation data was visible such as speed, alerts messages, etc. This…
A side detection module pin was corroded and was disrupting the electrical signals to major vehicle components, such as the dash (DIC). The DIC would lose communication with the rest of the vehicle while driving so no vehicle operation data was visible such as speed, alerts messages, etc. This likely also caused engine failure due to the incorrect operation of the afm which is on the same electrical circuit. No warning messages were given. The bad side detection module was diagnosed and fixed at a dealer and shortly after engine issues were noticed.
- Engine
Check engine light came on. Immediately went to reputable local repair shop. Shop advised push rod bent due to faulty engine. Advised to call GMC because not normal wear and tear. Called GMC expressed my frustration about this being preexisting issue w this engine. GMC corp told me I had to ship…
Check engine light came on. Immediately went to reputable local repair shop. Shop advised push rod bent due to faulty engine. Advised to call GMC because not normal wear and tear. Called GMC expressed my frustration about this being preexisting issue w this engine. GMC corp told me I had to ship to GMC dealership at my own expense then they could help me. Local GMCs backed up 6-8 wks. Towed car 1.5 hrs away. Mechanic told me not to worry this happens all of the time, GMC will take care of it. Pointed out a row of new trucks with my incl new Escalade with same issue. I spoke to a sales rep about trading my car in for new but he said engine issue still not resolved. He advised me to lease Escalade for $900 because by the time my engine blew my lease would be up; if not GMC fix under warranty!! Mechanic said new engine but GMC will take care of it. I waited 3+ months for GMC to authorize repair. GMC said they did not get docs but mechanic sent me verification of conversation and repair order sent to GMC. Mechanic received an unrelated warranty from GMC that said my issue was not covered. Mechanic said docs sent made no sense bc he sent the right warranty and he was sorry and embarrassed by GMC behavior. I finally paid over 14K for new engine. Picked up my car and drive a block and car still knocking and engine light came back on. I had returned my rental and no way home. In tears dealership gave me my rental keys back still all at my expense. The mechanic calls me two days later to tell me my torque needs to be replaced. I am hysterical, 14k spent, and car still not fixed. GMC told me to pay additional funds for torque converter or pick up. Threatened to charge storage fees. When I discussed their liability GMC became very rude and antagonistic. They cut off my communication with their lead mechanic. Took care of back to local repair shop. He said this smells of a law suit so would not touch vehicle. I all communication 106 more files to share.
- Power train
The contact owns a 2016 GMC Yukon. The contact stated while driving 70 MPH, and attempting to accelerate, the vehicle jerked, then briefly lost motive power before the engine seized. The contact was able to coast to the side of the road. The transmission warning light was illuminated. The vehicle…
The contact owns a 2016 GMC Yukon. The contact stated while driving 70 MPH, and attempting to accelerate, the vehicle jerked, then briefly lost motive power before the engine seized. The contact was able to coast to the side of the road. The transmission warning light was illuminated. The vehicle failed to restart. The vehicle was towed to a friend's residence. The vehicle was not diagnosed or repaired for the most recent failure. Days before the failure, the vehicle jerked while driving at various speeds. The vehicle was taken to Auto Zone; however, no cause for the failure was found. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 143,000.
- Electrical system · Fuel/propulsion system · Service brakes
Engine light keeps appearing and when checked it shows catalytic converter needs replaces and its sensors need replaced. Brake light has short in it and I repaireable
- Power train
Transmission shudders, lurches forward uncontrolably, and hard shifts
- Engine · Power train
2 months ago our 16 gmc Yukon Denali 6.2 bent a push rod on cylinder 4 . So had to fix it when I took out DOD lifters put them on work bench and about 10 minutes out the DOD lifters flew apart and know having transmission issues it’s starting to shudder ! So I would liked the [XXX] thing recalled…
2 months ago our 16 gmc Yukon Denali 6.2 bent a push rod on cylinder 4 . So had to fix it when I took out DOD lifters put them on work bench and about 10 minutes out the DOD lifters flew apart and know having transmission issues it’s starting to shudder ! So I would liked the [XXX] thing recalled because engine still isn’t right either it only has 130000 miles. I’ll never buy a [XXX] gmc because of problems! I want the [XXX] thing fixed ASAP we paid to much money for it to be having problems!!!! Please send a recall letter to fix it ! [XXX] . 4/29/2025 6:53 p:m INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Brake Vacuum Pump Failure
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado…
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011989This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
- 11011900This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
- 11011805This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when repairing wiring harnesses.
- 11011782This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
- 11011709This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
- 11011444This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
- 11011436This Preliminary information communicates for Technicians installing a Service Replacement Transmission Assembly to contact Technical Assistance to make sureunit is not suspect of a snap ring concern prior to installation.
- 11011420This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
- 11011205This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
- 11011119This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
- 11010576This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
- 11010566This service bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
- 11010545This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
- 11010495This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S. Only).
- 11010491This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
- 11010490This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
- 11010488This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
- 11010421This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
- 11009764This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
- 11009756This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
- 11009532This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
- 11009531This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
- 11009170This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
- 11009156This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
- 11009088This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
- 11009039This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
- 11009037This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
- 11008986This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
- 11008966This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
- 11008956This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
- 11008906This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
- 11008898The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
- 11007936This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
- 11007935This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and strut due to fluid leak.
- 11007788This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed rear wheel drive valve bodies.
- 11007780This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed rear wheel drive valve bodies.
- 11007776This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.
- 11007771This Preliminary information communicates diagnostic information for vehicles with transmission noise.
- 11007761This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
- 11007744This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Every GMC Yukon model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.