2020 GMC Yukon
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2020 GMC Yukon. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2020 GMC Yukon. Newest first.
General Motors, LLC (GM) is recalling certain 2026 Cadillac Escalade and Escalade ESV, Chevrolet Silverado 1500, Suburban, and Tahoe, and GMC Sierra 1500, Yukon, and Yukon XL vehicles with four-wheel (4WD) or all-wheel drive (AWD), and certain 2015-2020 Suburban, Escalade, Escalade ESV, Yukon, Yukon XL, and Tahoe vehicles. A component missing from the…
Risk and remedy
Risk
Front or rear wheel lockup increases the risk of a crash.
Remedy
Owners are advised not to drive their vehicle until the remedy is completed. Dealers will inspect and, if necessary, replace the transfer case assembly, free of charge. Owner notification letters were mailed May 18, 2026. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020 or Cadillac customer service at 1-800-333-4223. GM's number for this recall is N262557620. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 7, 2026.
General Motors LLC (GM) is recalling certain 2020 Buick Enclave, Cadillac XT4, XT5, Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, Traverse, GMC Yukon, Yukon XL, 2018-2021 Chevrolet Express, GMC Savana, 2019-2020 Chevrolet Blazer, Silverado 1500, GMC Acadia, Sierra 1500, and certain Continental tires sold to the aftermarket for various model year…
Risk and remedy
Risk
Over cured tires may develop a break in the sidewall resulting in sudden air loss or a belt edge separation which could lead to a tread/belt loss. Either condition can cause a loss of vehicle control, increasing the risk of a crash.
Remedy
GM will notify owners, and dealers will inspect the tires, replacing them as necessary, free of charge. The recall began March 22, 2021. Owners may contact GMC customer service at 1-888-988-7267, Buick customer service at 1-866-608-8080, Chevrolet customer service at 1-800-222-1020 or Cadillac customer service at 1-800-458-8006. GM's number for this recall is N212329050.
General Motors LLC (GM) is recalling certain 2020 Cadillac Escalade, Escalade ESV, Chevrolet Camaro, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles. The fuel pump may be missing a pressure regulator, allowing for over-pressurization of the fuel system.
Risk and remedy
Risk
Over-pressurization can crack the fuel pump and cause leaks, increasing the risk of a fire in the presence of an ignition source.
Remedy
GM will notify owners, and dealers will replace the fuel pump, free of charge. The recall began December 18, 2019. Owners may contact Cadillac customer service at 1-800-333-4223, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-888-988-7267. GM's number for this recall is N192283991.
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic…
Risk and remedy
Risk
Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy
GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Owner complaints
37 complaints
What owners report most
Latest complaints
- Power train
We have 42000 miles on this truck and bought 1 year old. Unit has been maintained well and looks new. Recently had the 10 speed transmissions fluid changed under normal maintenance. It was not burnt, turning more burgundy and dealer said it was a good and proper choice. Afterwards we noted a…
We have 42000 miles on this truck and bought 1 year old. Unit has been maintained well and looks new. Recently had the 10 speed transmissions fluid changed under normal maintenance. It was not burnt, turning more burgundy and dealer said it was a good and proper choice. Afterwards we noted a shudder and thought they made error or forgot to tighten something. Took truck back in for additional fluids and they had driveline associate drive. He said torque converter was going bad, and also warning these transmissions go bad unexpectedly and lock up. We have GMPP EXTENDED WARRANTY. Dealer requested replacement of torque converter and warranty required Field Tech due to price of repair. Field Tech drove truck, found metal in fluid and pan, and declined warranty repair and suggested more time was required. Essentially in hopes to push truck out of warranty coverage.
- Engine
Engine failure due main bearing and rod failure. Engine had heavy knocking.
- Engine
We just purchased our Yukon from a dealership in February (2/7/26) and it was diagnosed with premature failure of at least one AFM valve lifter as it is causing engine misfires, shaking and stalling on 7/30/26. We just hit 67,000 miles on the odometer so we are just beyond the warranty coverage. The lifters were replaced previously by the previous owners on 12/16/24.
- Power train
The contact owns a 2020 GMC Yukon. The contact stated that while driving at various speeds, the vehicle jerked and the transmission malfunctioned, causing the wheels to lock up and the check engine warning light to illuminate. The vehicle was driven to a local dealer who diagnosed that the…
The contact owns a 2020 GMC Yukon. The contact stated that while driving at various speeds, the vehicle jerked and the transmission malfunctioned, causing the wheels to lock up and the check engine warning light to illuminate. The vehicle was driven to a local dealer who diagnosed that the transmission clutch and pressure control solenoid had failed. The contact was advised that the transmission needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 26V289000 (Power Train). The contact stated that the vehicle experienced the same failure listed in the recall. The failure mileage was 118,000.
- Power train
Complete transmission failure at 82,000 miles. Well maintained vehicle, not used for towing or heavy hauling. Required complete replacement. Traveling at highway speeds and-according to repair facility- valve failure caused transmission to overheat a stripped gears, causing complete failure. Vehicle was unable to shift into any gears and was left inoperable. Required towing assistance and replacement.
- Electrical system · Service brakes · Wheels
Issue with the trailer brake system keeps coming up on my dash. I know a lot of other people have had the same issue keeps dinging will not stop causes me to get distracted while driving. Unable to use other features because of this distraction and safety issue. The safety issue needs to be fixed…
Issue with the trailer brake system keeps coming up on my dash. I know a lot of other people have had the same issue keeps dinging will not stop causes me to get distracted while driving. Unable to use other features because of this distraction and safety issue. The safety issue needs to be fixed this is an effective product with so many people having an issue you need to do a recall. I did let Graff Chevrolet in Mount Pleasant Michigan no and I took a picture and showed them.
- Power train
The contact owns a 2020 GMC Yukon. The contact stated that while depressing the accelerator pedal, there was an abnormal popping sound coming from the engine compartment, and the vehicle hesitated while accelerating. The cause of the failure was not yet determined. The manufacturer was notified of the failure, but no assistance was provided. The local dealer had not yet contacted. The failure mileage was 44,000.
- Unknown or other
My vehicle torque converter repair on my 2020 GMC Yukon is shuddering. Why is this not a recall when there are various Yukons that are experiencing shuddering related to torque converter repair. This should be a recall. The problem has been confirmed by a GMC dealer. There were not warning lamps, no messages, or other symptoms.
- Engine
I took my vehicle to a dealer to repair something unrelated to the engine. They said the oil pan was leaking and pulled the pan to discover the crank shaft bearings were failing. The vehicle has 53,765 miles at this point. This appears to be the same defect being recalled on the 2022 through 2024 models.
- Power train
Severe transmission shuttering destroyed my transmission and I need a new one according to a local body shop and a GMC service center. This is a KNOWN issue with these 10 speed transmissions, but they will not recall the ones from this year, they only recalled newer models. Car has been inspected…
Severe transmission shuttering destroyed my transmission and I need a new one according to a local body shop and a GMC service center. This is a KNOWN issue with these 10 speed transmissions, but they will not recall the ones from this year, they only recalled newer models. Car has been inspected by a local autobody shop, a 3rd party warranty company, and a GMC dealership service center. Shuddering causes severe shaking while driving between 25-65mph. No lights or other symptoms, just started occurring randomly. Purchased car Feb 2025, brought it in to local auto shop November 2025 and they could not get a transmission for months. They stated one was set to be delivered by GMC Feb 6th 2026 and they day before arrival GMC called them saying it was back on back order. Called the dealership in April 2026 and they stated they were not backordered. Had vehicle transferred to dealership service center and they say it’s still on national back order with no ETA. I have been waiting for over 6 MONTHS for a new transmission. This car has been undrivable for almost longer than I have been actually able to drive it.
- Engine · Power train
The 2020 Yukon started to have serious loss of speed and decelerating issue when the vehicle would slow down and down shift to a lower gear. The issue with this is that once it downshifted it woul not engage in a gear again and leave me stranded on the road. I had to turn off the car and restart…
The 2020 Yukon started to have serious loss of speed and decelerating issue when the vehicle would slow down and down shift to a lower gear. The issue with this is that once it downshifted it woul not engage in a gear again and leave me stranded on the road. I had to turn off the car and restart it for it to reengage in a gear enough to get it moving again and sometimes I had to try more than once to get it moving once it no longer wanted to engage in a gear. So in the 10 mile drive, I was left stranded at least 15 times. Each time I had to restart and restart again for the vehicle to engage in a lower gear. Once moving, it would sometimes it would engage in a higher gear and sometimes it would not. Thank goodness I wasn't traveling on the highway when this happened. Beware to anyone if this was to happen on the highway while in the middle lane while in traffic. And the check engine light never turned on and thus no code to help detect the issue. Took it the day before to have it looked at and was told nothing was wrong with it since there was a code and they could not duplicate the issue I described. WHAT?? They reset some transmission computer setting but it only made it worse by the next day. Now this 6 yr on 2020 GM Yukon is at the dealership service department requiring a new transmission for $7200. Said that the transmission fluid was showing particles of stuff and color was 'burnt', I think. Transmission fluid was changed at it's regular check up time so that didn't cause the issue and nor should it have bits and pieces in it and discolored. Is there any recourse to GM and it's crappy transmissions??
- Engine
TRANSMISSIONS ISSUES. Not transitioning/ shifting into gears smoothly or at all. When it does transition/shift it is rough and harsh. When my car transitions to a lower gear then it will not transition back up to a higher gear causing my vehicle to drop speed significantly that I am a safety…
TRANSMISSIONS ISSUES. Not transitioning/ shifting into gears smoothly or at all. When it does transition/shift it is rough and harsh. When my car transitions to a lower gear then it will not transition back up to a higher gear causing my vehicle to drop speed significantly that I am a safety hazard on the road. Example: when it shifts to a gear high enough that the vehicle can reach 40 mph and there is a need to decelerate it does but once it drop to lower gears it cannot engage again to a higher gear leaving me stuck going at most 10 mph with not opportunity to excelerate in traffic to a higher speed. The transmission control module (TCM) software was updated with no improvement.
- Forward collision avoidance › Warnings · Service brakes
I had an incident in my 2020 GMC Yukon, where the forward collision crash alert went off and there was total loss of brakes. The brake pedal went to the floor. After the crash alert ended, the brakes returned. This happened on the highway and could have turned into a disastrous event. The…
I had an incident in my 2020 GMC Yukon, where the forward collision crash alert went off and there was total loss of brakes. The brake pedal went to the floor. After the crash alert ended, the brakes returned. This happened on the highway and could have turned into a disastrous event. The dealership has been unable to diagnose or recreate this issue. They claim they did not find anything and the vehicle is safe to drive. I have turned off the collision detection system in the meantime. I feel strongly that this is a software issue that needs addressed. GM has replied that they support the dealership but if I want a second opinion I can go to another dealership for input.
- Engine
MISFIRE ON #6 CYLINDER. DIAGNOSIS REVEALED THE INTAKE VALVE IS NOT OPENING DUE TO COLLAPSED VALVE LIFTER. No message prior to engine light coming on and car shaking after driving back from the store (speed less than 45 MPH).
- Engine
I purchased my 2020 Yukon Denali on July 8, 2024 from Classic Buick GMC in Painesville, Ohio. The check engine light started going on and off a few months after purchasing the vehicle. When I called a mechanic he stated that I should wait until the light is on and then bring in the vehicle.…
I purchased my 2020 Yukon Denali on July 8, 2024 from Classic Buick GMC in Painesville, Ohio. The check engine light started going on and off a few months after purchasing the vehicle. When I called a mechanic he stated that I should wait until the light is on and then bring in the vehicle. In early May 2025, I took my vehicle to Mike’s Automotive in Middlefield, Ohio after the check engine light began coming on during extended drives (approximately five hours or more). The shop ran a diagnostic scan and advised that the oil pump needed to be replaced. Seeking another opinion, on May 14, 2025, I brought my vehicle to Classic Buick GMC Service, the dealership where I purchased my GMC Yukon. After diagnosing the vehicle, they advised that the check engine light was related to an Engine Oil Pressure Control Solenoid stuck in the off position (P06DD). This fix would cost $3,584. This fix would require the oil pump to be replaced as indicated by the previous repair shop. On May 29, 2025, I took the vehicle to Avenue Auto Clinic in Painesville, OH, where the oil pressure valve and sensors were replaced. The mechanic also advised that I change the oil every 3,000 miles, use OEM oil filters, and thicker oil. He also advised me to check the oil every 1,000 oil and add as needed. I do have to add oil approximately every 1,500 miles and I change the oil every 3,000 miles. I am concerned that my vehicle has the same engine-related defect as the Yukon engines currently under recall. Multiple mechanics have informed me that my vehicle is equipped with the same engine as those affected by the recall. I am requesting that my vehicle be added to the recall. Yes, my vehicle is available for inspection.
- Power train
Transmission started slipping a little and then literally stopped working all with in an hour. And was doa in the parking lot.
- Engine and engine cooling
The contact owns a 2020 GMC Yukon. The contact stated that while driving at an undisclosed speed, the check engine warning light was illuminated. The vehicle was taken to the residence, the contact exited the vehicle and discovered white smoke coming from the exhaust and started to smell coolant…
The contact owns a 2020 GMC Yukon. The contact stated that while driving at an undisclosed speed, the check engine warning light was illuminated. The vehicle was taken to the residence, the contact exited the vehicle and discovered white smoke coming from the exhaust and started to smell coolant and then discovered that the coolant level was low. The contact added coolant, and the check engine warning light was no longer illuminated. The contact’s husband and son, who were knowledgeable about vehicles, had self-diagnosed the vehicle and determined that the head gasket or the lifters might need to be replaced. The contact stated that the failure had occurred on several occasions and the contact consistently added coolant; however, the check engine warning light was illuminated every 300 miles once again. The contact researched and was made aware of an unknown NHTSA Campaign Number; however, the VIN was not included. The vehicle was taken to an independent mechanic, where it was diagnosed and determined that there was an unknown internal issue with the engine that was possibly associated with coolant leaking into the engine. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 52,000.
- Engine
I purchased a new 2020 GMC Yukon in May of 2020. Between May 2020 and November 2025 the vehicle was routinely serviced on or before the due date recommend by the manufacturer. I had not experienced issues with the vehicle until November 2020 when the check engine light abruptly appeared and the…
I purchased a new 2020 GMC Yukon in May of 2020. Between May 2020 and November 2025 the vehicle was routinely serviced on or before the due date recommend by the manufacturer. I had not experienced issues with the vehicle until November 2020 when the check engine light abruptly appeared and the vehicle began driving very rough. I immediately took the vehicle to the local mechanic who identified two codes (P0300 and P050D) related to the engine issues. The vehicle was towed to the dealership due to the fact that I was instructed it was unsafe to drive long distances without additional diagnostics. The dealership disassembled the engine and found coolant leaking into cylinder six. There were no cracks or otherwise clear means of entry for the coolant into the engine. The dealership instructed us that we would need a complete engine replacement. Upon further research of this issue, it was uncovered that a Service Bulletin had been issued for this very issue. The reference number is 20-NA-166, updated March 2024.
- Engine
total engine failure with 90,000 miles on the car.
- Engine
We purchased the vehicle used in April 2025 with 79,851 miles. All service records were documented via Carfax. Vehicle was in impeccable condition. We drove it for approx. 8,000 miles until July 10, 2025, when a loud knocking sound started coming from the engine - approx. mileage 87,600. We drove…
We purchased the vehicle used in April 2025 with 79,851 miles. All service records were documented via Carfax. Vehicle was in impeccable condition. We drove it for approx. 8,000 miles until July 10, 2025, when a loud knocking sound started coming from the engine - approx. mileage 87,600. We drove the vehicle home 350 miles. The knocking sound continued and got slightly worse. We drove it to the nearest dealer (30 miles) and the mechanic said it sounded like a camshaft problem. However, they could not get it in for over 60 days. We drove to another dealer (45 miles). The mechanic said he thought the entire engine was bad. We left the vehicle there and about a week later they were able to confirm that it was TOTAL BEARING FAILURE. Mileage 88,054. We were told that a new engine was needed as well as a radiator and new oil lines, etc. Total estimate $18,000. They also said there was no timeline they could guarantee because of the current GM recall. Of particular note and concern...at no time did the 'check engine' light come on or any other warning system activate. Both mechanics were genuinely perplexed at this. The repairs were ordered and the vehicle is now repaired. However, GM has not confirmed a cost share for the repair billing and we are now almost 60 days since they received the paperwork from the dealer so we still do not have our vehicle back. We filed a complaint with GM and a case number was assigned so they are fully aware of the issue as is the dealer who did the repair.
- Engine · Unknown or other
My vehicle went from driving perfectly to startling and not going pass 45 in a matter of two days. I was getting all maintenance done at dealer always on time had just service it. When all of a sudden it started making a jerking/ skipping feel as if I was accelerating too hard. Took it to get…
My vehicle went from driving perfectly to startling and not going pass 45 in a matter of two days. I was getting all maintenance done at dealer always on time had just service it. When all of a sudden it started making a jerking/ skipping feel as if I was accelerating too hard. Took it to get checked and the code that came up was (TCC)torque converter clutch. I spent 6000 to rebuild the transmission and kno the engine has a tap tap noise. Once again I took it in and now it’s the lifters in the engine. No warning light have ever popped up
- Engine
While driving to Lake Placid, NY, I experienced sudden loss of propulsion as I was driving approximately 60 mph. I was able to brake and pull over to the shoulder. I was not able to restart the vehicle - engine was dead. We were flat bed towed to a garage in Lake Placid where it was confirmed that…
While driving to Lake Placid, NY, I experienced sudden loss of propulsion as I was driving approximately 60 mph. I was able to brake and pull over to the shoulder. I was not able to restart the vehicle - engine was dead. We were flat bed towed to a garage in Lake Placid where it was confirmed that the engine was inoperable. The vehicle is now at. GM dealer in Potsdam, NY. I believe this engine should be part of the recall!!
- Power train
The contact owns a 2020 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently lost motive power, prompting the contact to pull over to the shoulder of the roadway. The contact became aware that the vehicle continued to move forward while shifted into…
The contact owns a 2020 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle inadvertently lost motive power, prompting the contact to pull over to the shoulder of the roadway. The contact became aware that the vehicle continued to move forward while shifted into Park, Neutral, or Reverse. The contact stated that the message "Transmission Overheating" was then illuminated. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 119,000. The contact declined to provide the VIN.
- Power train
The contact's wife owns a 2020 GMC Yukon. The contact stated the vehicle was taken to an independent mechanic for a tune up. The contact stated that upon picking up the vehicle and driving, the transmission was slipping in and out of gear. Additionally, the contact stated while at a complete stop…
The contact's wife owns a 2020 GMC Yukon. The contact stated the vehicle was taken to an independent mechanic for a tune up. The contact stated that upon picking up the vehicle and driving, the transmission was slipping in and out of gear. Additionally, the contact stated while at a complete stop and depressing the accelerator pedal, the engine revved; however, the vehicle hesitated to respond, and the vehicle jerked while responding. The contact stated that the vehicle slowly picked up speed, and the transmission was slipping in and out of gear. There was no warning light illuminated. The contact stated that his wife had noticed that the vehicle made an abnormal sound while driving. The vehicle was taken to the dealer, where it was diagnosed that the torque converter had failed. The dealer determined that the transmission needed to be replaced. The vehicle was repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 107,267.
- Unknown or other
Hello, I’m calling about the GM transmission recall recently announced in March 2025 affecting 2020 Yukon vehicles. My Yukon experienced what I believe is the exact same issue described in the recall. Our vehicle lost forward gears and almost caused a crash. A certified mechanic confirmed the…
Hello, I’m calling about the GM transmission recall recently announced in March 2025 affecting 2020 Yukon vehicles. My Yukon experienced what I believe is the exact same issue described in the recall. Our vehicle lost forward gears and almost caused a crash. A certified mechanic confirmed the transmission fluid was burnt and full of clutch material, with internal transmission damage. We are asking for this to be handled under the recall, as the issue directly matches GM’s known safety defect. We need this resolved immediately — the vehicle is unsafe to drive and the failure happened before we even knew about the recall. Our GMC Mechanic stated the following : Needs immediate attention Recommended service Transmission: test drove verified no forward gears after 3 minutes of driving. fluid brown and burnt full of clutch material. internal damage to transmission. A transmission flush is a process that makes it possible to clear the old transmission fluid from the vehicle's transmission. This process also helps to remove residue of older transmission fluid from the converters, coolers, and cooler lines that often are part of the design for the transmission.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11012009This bulletin helps aid the tech in possible transmission noise that may be normal or abnormal depending on the concern noted.
- 11011996This service bulletin provides diagnostic/repair information to correct a customer concern of Cellphone not Charging or USB Receptacle Inoperative.
- 11011989This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
- 11011900This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
- 11011805This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when repairing wiring harnesses.
- 11011782This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
- 11011709This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles before being sold (prepping) to the customer.
- 11011444This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM technical assistance case using the dealer case management tool.
- 11011436This Preliminary information communicates for Technicians installing a Service Replacement Transmission Assembly to contact Technical Assistance to make sureunit is not suspect of a snap ring concern prior to installation.
- 11011420This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
- 11011406This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
- 11011367This informational bulletin provides a guide on how to diagnose and test for vibrations utilizing the PicoScope.
- 11011205This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance Schedules.
- 11011182This engineering information (EI) closure ends the need for gathering further information from technicians in regard to a Chirp, Squeal, and/or Whine Type Noise Heard from Front of Vehicle During a Cold Start and/or While in Operation.
- 11011119This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
- 11010901This bulletin provides a procedure on how to check for a battery drain utilizing the Picoscope and how to measure the load on the system that may be causing a drain.
- 11010639This informational bulletin advises the tech and the customer of a normal DEF operation while under high load conditions and when the time is right to fill the DEF at that time frame.
- 11010576This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
- 11010566This service bulletin provides frame coating repair information to correct a customer concern of wax coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
- 11010545This service bulletin provides information on key code security rules and information on GM keycode look-up applications (U.S).
- 11010495This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S. Only).
- 11010493This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty Coverage Period.
- 11010491This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance programs.
- 11010490This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
- 11010488This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center (WPC) Parts Return Program.
- 11010421This warranty administration bulletin provides policy information on the requirements for 12V battery testing and warranty replacements.
- 11009764This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
- 11009760This service bulletin provides information on the Transport Mode Feature, also known as Logistics mode, which is used to increase the 12V Battery stand time of the vehicle during transit and or long period of stand time at the dealerships.
- 11009756This bulletin provides information on Policies Applicable to All U.S. Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
- 11009532This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
- 11009531This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent additive.
- 11009529This engineering information (EI) is requesting information from technicians to perform the check list provided and contact the engineer listed in regards on hearing one or more of the following noises coming from the front of the vehicle during a cold start and/or while in operation.
- 11009170This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when working on a LIN bus.
- 11009156This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
- 11009088This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
- 11009039This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
- 11009037This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
- 11008986This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes U**** Byte 71 DTC.
- 11008966This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
- 11008956This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S. and Canada Dealers Only).
Every GMC Yukon model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.