1993 Nissan Quest
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Nissan › Quest › 1993
These records cover every 1993 Nissan Quest. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 1993 Nissan Quest. Newest first.
Vehicle description: minivans. the fuel tank vent hose allows air to vent from the fuel tank during refueling. cracks have developed in the vent hose. if (1) the fuel tank IS overfilled, not allowing excess fuel in the vent hose to flow back into the tank, (2) the vehicle IS driven only a short distance after refueling and, (3) there IS subsequently…
Risk and remedy
Risk
Fuel leakage in the presence of an ignition source can result in a fire.
Remedy
Dealers will replace the vent hose.
Leaves and other foreign material can enter through the cowl panel air intake during operation of the front heater and/or air conditioning system resulting in a build-up of material in the plenum. This can lead to noise, odors, or in some cases, ignition of these materials.
Risk and remedy
Risk
A vehicle fire could occur.
Remedy
Dealers will install an additional heater/air conditioning system intake screen.
Fuel filler hoses may have been cut prior to installation by a utility knife used to open the shipping box.
Risk and remedy
Risk
Fuel leakage can result if the cut extended through thethickness of the hose wall. Leaking fuel can result in a fire if exposedto a source of ignition.
Remedy
Replace the fuel filler hose.
The service brake master cylinder was not properly assembled or could have been damaged by the evacuation and filling of the brake system at the assembly plant.
Risk and remedy
Risk
This can result in a partial brake system failure due tointernal master cylinder leakage which can cause loss of braking on two of thefour wheels. If this occurs, there would be increased brake pedal travel, higherpedal efforts and increased stopping distances.
Remedy
A new brake master cylinder will be installed.
One or both of the bolts securing the automatic seat belt restraint system tracks to the b-pillars were not adequately tightened.
Risk and remedy
Risk
This condition can result in the automatic seat beltsystem track joints having less than design strength, and increase the risk ofinjury to the seat occupant in the event of a collision or sudden stop.
Remedy
Dealers will tighten the passive restraint system track mounting bolts.
Owner complaints
118 complaints4 involved a crash9 involved a fire4 injuries
What owners report most
Latest complaints
- Service brakes, hydraulic · Structure
Steel brake lines to rear breaks rusted through in several places - two lines to rear that pass under the floor and along the driver side rail and over the rear left wheel axle, and also at the area immediately before each rear wheel cylinder. *Tr
- Seat belts · Seat belts › Front › Buckle assembly
Tl*the contact owns a 1993 nissan quest. The contact stated that the passenger front lap belt will not remain secure into the buckle. As a consequence, in the event of the crash the occupants may not be properly restrained, which can cause serious injury. He took the vehicle to the dealer and a…
Tl*the contact owns a 1993 nissan quest. The contact stated that the passenger front lap belt will not remain secure into the buckle. As a consequence, in the event of the crash the occupants may not be properly restrained, which can cause serious injury. He took the vehicle to the dealer and a technician stated that no parts are available to properly remedy the failure. The vehicle has not been repaired. The failure and current mileages were 170,000. updated 10/06/09. *lj the consumer stated the vehicle has finally been repaired. The dealer ordered and replaced the belt buckle free of charge under warranty. Updated 10/06/09
- Fuel system, gasoline · Seat belts · Structure › Body · Suspension
Tl*the contact owns a 1993 nissan quest. the contact stated that the vehicle burned a lot of fuel. the mechanic inspected the vehicle and stated that there are no leaks. in addition, the contact heard a scraping noise when make a left or right turn. the mechanic was unable to diagnose the…
Tl*the contact owns a 1993 nissan quest. the contact stated that the vehicle burned a lot of fuel. the mechanic inspected the vehicle and stated that there are no leaks. in addition, the contact heard a scraping noise when make a left or right turn. the mechanic was unable to diagnose the failure. the current mileage was 200,050 and failure mileage was 200,00. updated 04/08/08. *lj the seat belts did would not go up or down and there was a problem with the upper and lower ball joints. The consumer also stated the vehicle cuts off. Updated
- Fuel system, gasoline › Storage › Tank assembly
Tl*the contact owns a 1993 nissan quest. after parking the vehicle, the contact noticed smoke coming from the vent on the outside of the vehicle. after a couple of minutes, the smoke cleared. she turned the key in the ignition and flames appeared under the glove compartment. the fire and police…
Tl*the contact owns a 1993 nissan quest. after parking the vehicle, the contact noticed smoke coming from the vent on the outside of the vehicle. after a couple of minutes, the smoke cleared. she turned the key in the ignition and flames appeared under the glove compartment. the fire and police departments arrived at the scene and a fire report was filed. the vehicle was destroyed. the dealer stated that the vin was included in nhtsa campaign ID number 00v419001 (fuel system, gasoline:storage:tank assembly); however, the contact never received a recall notice. the current and failure mileages were 200,000.
- Service brakes, hydraulic › Foundation components › Master cylinder
Tl*the contact owns a 1993 nissan quest. the contact stated that her vehicle was squeaking and that she had to hose off her front rotors when they overheated. her vehicle was also experiencing long stopping distances. the failures have occurred on numerous occasions. recently, the service brake…
Tl*the contact owns a 1993 nissan quest. the contact stated that her vehicle was squeaking and that she had to hose off her front rotors when they overheated. her vehicle was also experiencing long stopping distances. the failures have occurred on numerous occasions. recently, the service brake light illuminated for a couple of days and then dimmed. safety recall # 92v32001 (service brakes, hydraulic: foundation components: master cylinder) was found. the free portion of the safety recall no longer applies to this vehicle. the powertrain was unknown. the current and failure mileages were 200,000.
- Fuel system, gasoline › Delivery › Hoses, lines/piping, and fittings
Fuel filler vent leak .nar 1/21/03. the customer requested reimbursement. *jb
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
Exhaust manifold bolts broken nissan replaced bolts 1800.00 20,000 miles later same problem nissan says not responsible because it had been longer than 20,000 miles as far as I can tell nissan did not use the new improved manifold bolts for this repair.*ak
- Engine and engine cooling › Exhaust system · Unknown or other · Visibility › Power window devices and controls
As has happened to close to 100% of quest/mercury villager owners, I have cracked manifolds, missing manifold studs, and several broken manifold studs. this results in poor starts, exhaust leaks, and a noticeable "clacking" (exhaust leak) upon acceleration. my vehicle has 118K miles. I…
As has happened to close to 100% of quest/mercury villager owners, I have cracked manifolds, missing manifold studs, and several broken manifold studs. this results in poor starts, exhaust leaks, and a noticeable "clacking" (exhaust leak) upon acceleration. my vehicle has 118K miles. I understand the labor for a complete fix can run over $1000, while parts run under $100. I have contacted 1-800-nissan1 with this issue and the operator was aware of this very common, serious problem and affirmed that I would be contacted with any possible compensation.
- Seat belts
Front drivers automatic seat belt IS stuck in one stationary position. consumer can hear motor running but no movement of seatbelt. *ak
- Engine and engine cooling › Exhaust system
Intermittently there IS a gas smell in the passenger cabin. the smell commonly occurs when the fuel tank IS close to empty. *ak
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
Consumer states the exhaust manifold studs have broken four times in as many years, causing exhaust leaks.
- Equipment › Appliance › Air conditioner
Air conditioning system caught on fire, blowing flames from burning plastic into passenger compartment, while driving on residential street w/ ac on. problem diagnosed as leaves crumbling then falling through area where windshield wipers sit into the ac blower intake, then sitting in the blower.…
Air conditioning system caught on fire, blowing flames from burning plastic into passenger compartment, while driving on residential street w/ ac on. problem diagnosed as leaves crumbling then falling through area where windshield wipers sit into the ac blower intake, then sitting in the blower. resistor sits next to blower, gets "almost red-hot" when ac IS on; the heat ignited the leaves in the blower, the plastic caught on fire, and fumes from leaves and burning ac system were blown into passenger compartment. the shop (albany hill auto) said the blower should have had a grate over the intake to keep leaves out and the intake was poorly positioned to begin with.*ak
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
Consumer complains of the manifold developing a leak on both sides. *jg
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
Exhaust manifold bolt failures, missing and broken off without any warning and the intermittent engagement of the windshield wipers when the turn signals are applied. The washers for the windshield works occasionally and the wipers themselves function erratically.*ak
- Fuel system, gasoline › Delivery · Service brakes, hydraulic › Foundation components › Hoses, lines/piping, and fittings
Gas and brake lines are located where they are exposed and can be easily corroded,causing vehicle to leak fuel. This can result in a fire.*ak
- Fuel system, gasoline › Storage › Tank assembly
Gas tank developed leaks. Strong fumes were apparent. The leaks developed on top of the tank.*ak
- Equipment › Appliance › Air conditioner · Equipment › Electrical · Fuel system, gasoline › Storage › Tank assembly
Prior to reall notice, consumer experienced problems with the fuel hose and it was replaced, consumer IS now requesting reimbursement.*jb
- Engine and engine cooling › Engine
While entering into a parking lot there was a loud noise, crankshaft fell off. Mechanic stated there was no diagnostic after looking at vehicle. Also, engine has to be replaced. Manufacturer has been notified and responded that vehicle was no longer under warranty.*ak engine replaced at owners expense. consumer feels dealer should take reponsibility for claim. *tt
- Engine and engine cooling › Exhaust system
I am experiencing a very common problem with my nissan vehciles. I have located the same problem throughout your complaints database for many nissan models and various years. I need your help in resolving this problem with the dealer. They should issue a recall or pay for all repairs. Please refer…
I am experiencing a very common problem with my nissan vehciles. I have located the same problem throughout your complaints database for many nissan models and various years. I need your help in resolving this problem with the dealer. They should issue a recall or pay for all repairs. Please refer to the numerous complaints on your web site such as the following for the '94 nissan quest:odi #s- 718520, 710278, 835965, 781102, 781100, 720610, 533368, 781099, 715129, 720103, 722946, 850195.....i can find alot more odi numbers for the same problem for the '1993-'1995 quests, pathfinders, maximas, etc. Nissan IS hiding a major problem.* no safety defect mentioned in summary. *Ak
- Service brakes, hydraulic › Foundation components
When there IS pressure on brakes, pedal stays in same applied position and brakes release, allowingvehicle to roll. this happened on 3 occasions.when car will coast while applying brake,and when going down hill and in stop position, brakes will release. Contacted dealer, and dealer checked for service bulletins and warnings.*ak
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
The exhaust manifold snapped off at least one of the bolts holding the cover on. john at magic muffler in thousand oaks (805-496-2436) pointed out the problem to us and said it was very common in the nissan quests. my brother also had the same problem with his quest on more then one occasion.…
The exhaust manifold snapped off at least one of the bolts holding the cover on. john at magic muffler in thousand oaks (805-496-2436) pointed out the problem to us and said it was very common in the nissan quests. my brother also had the same problem with his quest on more then one occasion. the exhaust manifold supposedly warps and snaps the bolts holding it on. nissan said that there IS no recall for this problem? if it IS a common problem or flaw in design, why IS there not a recall? I was informed from several different repair shops that this would cost me $320 to $1600 depending on how many of the bolts are broken off into the housing.*ak
- Latches/locks/linkages › Doors › Latch
Drivers side door cannot be opened at all, even in an emergency. *Ak
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
Exhaust maniflod bolts sheered off. Consumer did not know of this until failing inspection. Nissan has been contacted.*ak
- Engine and engine cooling › Engine › Gasoline · Latches/locks/linkages › Doors › Latch · Unknown or other
Engine check light keeps coming on. Sometimes would go out infrequently. Took to mechanic, and was informed needed to put on diagnostic machine. sliding door lock fails to open from the outside. Need to be inside to unlock it.*ak 8SLC
- Engine and engine cooling › Exhaust system › Emission control · Fuel system, gasoline › Storage › Tank assembly
Consumer had vehicle at dealer to get recall repairs done for a fuel vent hose, but it was other vent hose that had the problem. dealer changed hose, but at owner's cost.*ak 00v419001 was recall number, consumer states failed part was spreading strong gas fumes. *slc
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Fuel tank vent hose leakage
Periodic exposure to liquid gasoline may result in extraction of antidegradants from the subject fuel tank vent hose.hoses which have suffered loss of antidegradant can develop cracks in areas of high strain.fuel may spray or drip from cracked vent hoses following tank fill.starting at JOB#1 1998 my (california…
Periodic exposure to liquid gasoline may result in extraction of antidegradants from the subject fuel tank vent hose.hoses which have suffered loss of antidegradant can develop cracks in areas of high strain.fuel may spray or drip from cracked vent hoses following tank fill.starting at JOB#1 1998 my (california emissions vehicles) and JOB#1 1999 my (federal emissions vehicles), the subject vent hose composition changed from nitrile rubber hoses with chloroprene rubber covers (nbr/cr) to fluoracbon rubber hoses which an outer layer blend of nbr/pvc.the changes wer made to improve hydracarbon resistance for complaince with new evaporative emissions regulations.the modified hoses are also significantly more resistant ot degradation and craciking. In a letter dated december 14, 2000, nissan notified nhtsa that it will conduct a safety recall campaign to replace the subject vent hose in affectd vehicles with the redesigned hose.nissan will begin notifying owners of the affected vehicles on february 5, 2001.nissan will finish its owner mailings on september 10, 2001.owners will be notified in reverse order of vehicle age.
- Backlite shattering
There is no summary currently available
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10243708DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10239062SILICONE-BASED LUBRICANT OR GREASE CAN DAMAGE ELECTRICAL COMPONENTS SERVICE INFORMATION Do not apply Silicone-based lubricants or grease to, or around, any interior electrical components. To avoid the risk of death or severe personal injury, do not directly spray Silicone-based lubricant or grease, or inadvertently overspray Silicone-based lubricant or grease onto any interior electrical components. These types of lubricants can be detrimental to the proper operation of electrical components.
- 1023906012 VOLT BATTERY TESTING FOR IN-SERVICE VEHICLES SERVICE INFORMATION The following Service Information lists NNA procedural recommendations for establishing good connections while performing 12V battery testing. These recommendations are expected to promote uniformity during the connection process, therefore reducing the number of incorrect Test with DCA and Replace results. HINT: If 12 volt batteries are allowed to discharge for a prolonged period of time, battery life may be drastically reduced. This condition may lead to premature battery replacement and customer dissatisfaction. IMPORTANT: CPX-900 is now an accepted testing tool to use along with or in place of the DSS-5000 CPX-900 operating instructions are found at: https://nissancpx900.midtronics.com/ DSS-5000 operating instructions are found at: https://nissandss5000.midtronics.com/ DCA-8000 is now a required testing tool to be used for all warranty replacement decisions. The DCA-8000 is also a more efficient charger than previously available, and will charge any available 12 volt lead acid battery safely and accurately as long as all precautions and inputs are made correctly. The DCA-8000 operating instructions are found at: https://nissandca8000.midtronics.com/
- 10235710INTELLIGENT KEY REPLACEMENT OR SWAPPING BETWEEN VEHICLES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
- 10235707VEHICLE KEY NOT DETECTED / AUTHENTICATED, ENGINE WILL NOT START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232658REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232657WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232656WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10232652DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10206391STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10192305SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
- 10192233Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail.
- 10192217If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
- 10192216SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
- 10192145SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
- 10188377STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
- 10051767Nissan: lock/unlock request button on outside handle does not respond.
- 10032506Nissan: vent control valve replacement. When replacing the evap canister vent control valve for reason: use the one listed on page 2; for vent control valve replacement procedure, refer to the appropriate section of the electronic service manuals (esm; when installing the new valve, do not add any lube to its o ring; for frontier (D40 series) only, install the protector listed in parts information. Includes 2005-09 frontier. Updated 12/8/10.
- 10031305Nissan: tire pressure monitoring system (TPMS) warning light on/flashing. No models or model years listed. Updated on 08-11-2011.
- 10030165Nissan: the 12 volt battery IS an important part of the vehicle electrical system and IS required to stay connected when the engine IS running. To prevent damage to vehicle electronic components follow the instructions/cautions. No model years listed.
- 628997Some vehicles may exhibit a pop noise from the sliding door while driving.
- 628213Subject regrding sliding door pop noise while driving.
- 606182Key value brake pad service information.
- 604996Concerns with fuel pump whining noise.
- 604301Service information on key value brake pads.
- 603260Some vehicles experience rear main seal retainer gasket leaking oil.
- 602817Exhibiting a condtion where the rear dedge of the 2ND side window IS not fluch with the fornt edge of the 3RD window and / or the rear edge of the 3RD window IS not flush with the vehicle body when the window IS fully closed.
- 602672Some vehicles are exhibiting excessive gear whine noise coming from the transaxle.
- 601729Some vehicles has an egr malfunction due to cracked bpt valve bottom hose.
- 601724Exhibiting an air leak noise from the upper rear corne of the front door window glass(s).
- 601721Condition with the rear main seal retainer gasket leaking oil.
- 53579Provided information on sliding door rail guide corrosion.
- 46392If there IS a 'gear whine' noise between 32 and 45 mph when in od (4TH gear) under light acceleration, the cause may be the planetary gear assembly. This whine noise will not be heard in 3RD gear at any speed. Replaced the front sun and front planetary gears.
- 46391If an owner of a 1993 - 1995 quest (V40) vehicle complains of a rattle or squeak appearing to originate from the unoccupied center bench or bucket seat area while driving the vehicle, replacement of the grommet in the rear floor anchor hook amd modification of the front latch mounting holes IS recommended. With the holes modified, the front latches can be adjusted using the following detailed instructions.
- 45800Water leaks in the left and/or right rear interior of the vehicle, the cause may be a rise in the flexible tubing that drains water from the guide rail assembly around the sunroof.
- 39660A/t burnt fluid and/or metal shavings.
- 39657Battery discharge due to rear hatch left ajar.
- 39640Quest front blower noise.
- 39331Fuel odor when driving on hot days.
- 37997Automatic transmission slipping.
Every Nissan Quest model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.