2021 Ford Edge
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2021 Ford Edge. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2021 Ford Edge. Newest first.
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Risk and remedy
Risk
A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy
The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to…
Risk and remedy
Risk
A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy
The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Ford Motor Company (Ford) is recalling certain 2021-2022 Edge vehicles previously repaired incorrectly under recall number 22V-151. A software error may cause the rearview camera to display a blank or distorted image when the vehicle is in reverse.
Risk and remedy
Risk
A rearview camera that displays a blank or distorted image can reduce the driver's view of what is behind the vehicle, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed April 25, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S28.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
Risk and remedy
Risk
A loss of drive power increases the risk of a crash.
Remedy
Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55.
Ford Motor Company (Ford) is recalling certain 2021-2022 Edge vehicles. A software error may cause the rearview camera to display a blank or distorted image when the vehicle is in reverse.
Risk and remedy
Risk
A rearview camera that displays a blank or distorted image can reduce the driver's view of what is behind the vehicle, increasing the risk of a crash.
Remedy
The rearview camera software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on April 29, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S14.
Ford Motor Company (Ford) is recalling certain 2021 Edge vehicles. The driver's seat belt retractor pretensioner assembly may not function correctly when activated during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Risk and remedy
Risk
A seatbelt assembly that does not function as intended can increase the risk of injury during a crash.
Remedy
Dealers will replace the driver's seat belt retractor pretensioner assembly, free of charge. Owner notification letters were mailed on June 15, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C13.
Ford Motor Company (Ford) is recalling certain 2020-2021 Edge, 2020 Lincoln Nautilus and Ford Escape and 2021 Lincoln Corsair and Ford Bronco Sport vehicles. An inadequate amount of lubricant in the rear drive unit may cause seizure of the rear drive axle.
Risk and remedy
Risk
If the rear drive unit seizes, there may be a loss of drive and/or a loss of vehicle control, increasing the risk of a crash.
Remedy
Ford will notify owners, and dealers will check the rear drive unit lubricant level. Axles found to have lubricant at the minimum level will be filled to the full level. Axles found to be below the minimum lubricant fill level will be replaced, free of charge. This recall began March 12, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S02.
Owner complaints
114 complaints4 involved a crash1 involved a fire1 injuries
What owners report most
Latest complaints
- Power train
The transmission jerks VERY strongly when shifting gears between 5mph - 60mpg. It is so pronounced that it effects my foot on the pedals and could cause drivers to slam on the accelerator or brake. The vehicle has 90k miles on it and this issue has been happening for 10k miles or so. This is a KNOWN issue with the 8F35 transmission and needs to be a recall instead of a TSB that costs drivers $5k.
- Power train
I have transmission failure at 63,000 miles. safety issue because it won't accelerate without shuttering could cause an accident. I have a Ford dealer email and repair order.
- Power train
Transmission shudder, vehicle only has 87K miles on it. Ford knows it's an issue and has issued TSBs on this exact problem.
- Back over prevention
See attached document for complaint.
- Power train
Upon accelerating from a stop the car shutters.
- Unknown or other
The left rear axle housing due to not enough lubricant. The ford maintenance shop states they can refill the lubricant but it doesn’t last long and will be back in the shop . So I’m having it replaced due to their recommendation which is a $1,835.00 fix. I see there were recalls on 2021 edges but…
The left rear axle housing due to not enough lubricant. The ford maintenance shop states they can refill the lubricant but it doesn’t last long and will be back in the shop . So I’m having it replaced due to their recommendation which is a $1,835.00 fix. I see there were recalls on 2021 edges but mine wasn’t built in the right time frame apparently and it’s ironic that it is the same exact problem with several 2021 Edges but yet only the ones built in certain months are getting recalled. Makes no sense that if this is hazardous then for safety reasons shouldn’t there be a recall on all of them no matter where or what month they were built. Very disturbing and disappointing. It sure sheds some light on the Ford manufacturing!
- Power train
The vehicle hesitates, bucks, and surges when accelerating from low speed making it difficult and hazardous merging into traffic and other driving situations. The hesitation, bucking, and surging is getting progressively this happened around 70k miles. The mechanic is saying it needs to be replaced completely for 12k!
- Power train
The transmission failed causing the car to sputter and stop. My daughter was driving the car at the time and it died while she was waiting for a light to turn green at a major intersection. She had to wait for my husband to come assist her. We had it towed to McCree Ford in Dickinson, TX. They…
The transmission failed causing the car to sputter and stop. My daughter was driving the car at the time and it died while she was waiting for a light to turn green at a major intersection. She had to wait for my husband to come assist her. We had it towed to McCree Ford in Dickinson, TX. They indicated it was the transmission and it would need to be replaced. No indication of any issues prior to this incident. The car was well maintained up until this incident and we were just short of 100,000 miles. Mostly highway miles.
- Back over prevention
The contact owns a 2021 Ford Edge. The contact received notification for NHTSA Campaign Number: 26V124000 (Back Over Prevention); however, the part to perform the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall…
The contact owns a 2021 Ford Edge. The contact received notification for NHTSA Campaign Number: 26V124000 (Back Over Prevention); however, the part to perform the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The vehicle was taken to a dealer, where the contact was informed that the USB port needed to perform the software update was defective. The dealer did not provide the alternative option included in the recall remedy, which authorized an over-the-air (OTA) software update free of charge. The vehicle was not repaired. The manufacturer was notified of the failure, and a case was opened. The contact had not experienced a failure.
- Back over prevention › Rearview system braking · Electrical system · Visibility/wiper
The “fix” for the rear camera has not resolved the issue. My rear camera worked for a short time after the fix was downloaded, but then stopped working. I don’t know what to do to fix it.
- Power train
I bought a 2021 Ford Edge SEL in April 2024. I had problems with the car jurking at low speeds pretty much the whole time I had it. I just recently had to replace my transmission due to the whole thing failing. It just randomly went out while driving.
- Power train
My 2021 Ford Edge is experiencing a severe transmission defect. When accelerating between 22 mph and 35 mph, the vehicle hesitates, stumbles, and shudders violently (transmission shudder). The transmission struggles to engage gears properly, causing unexpected jerking and a sudden loss of…
My 2021 Ford Edge is experiencing a severe transmission defect. When accelerating between 22 mph and 35 mph, the vehicle hesitates, stumbles, and shudders violently (transmission shudder). The transmission struggles to engage gears properly, causing unexpected jerking and a sudden loss of acceleration power. This behavior creates a dangerous driving hazard when merging into traffic or changing lanes. This issue is consistent with Ford's Technical Service Bulletin (TSB 21-2092) regarding the 8F35 8-speed automatic transmission.
- Engine
When driving at lower speeds the car jerks/misses. A local Ford dealership confirmed it's the torque converter. Even purchased a warranty that is suppose to cover the issue and even they are being difficult about wanting to fix it!
- Engine · Fuel/propulsion system · Unknown or other
There should be a recall on the sunvisors. Because it is a safety issue, because when the Sun is in your face and you can't see driving it can very well cause an accident or getting a ticket for not being able to see your speed that you're going, because you're so far up trying to get the Sun out…
There should be a recall on the sunvisors. Because it is a safety issue, because when the Sun is in your face and you can't see driving it can very well cause an accident or getting a ticket for not being able to see your speed that you're going, because you're so far up trying to get the Sun out of your face. You can't see any of the controls or your dashboard.. That is a safety hazard. My driver's side one is broken. I can't use it at all and I'm not paying $200 to get it fixed. That's insane on top of that.My passenger side is one is starting to break as well. Also, my car is very sluggish. When i'm driving, it is sluggish back and forth like it doesn't get good acceleration.There should be a recall for that.As well. I've also noticed when I'm stopped at a light, and I slowly let off the brake the car start to jump.
- Engine
Torque converter needs a replacing
- Engine and engine cooling
The contact owns a 2021 Ford Edge. The contact received notification of NHTSA Campaign Number: 24V635000 (Engine and Engine Cooling). The local dealer was contacted, and the contact was informed that the recall repair was performed remotely. The contact stated that the dealer had exceeded a…
The contact owns a 2021 Ford Edge. The contact received notification of NHTSA Campaign Number: 24V635000 (Engine and Engine Cooling). The local dealer was contacted, and the contact was informed that the recall repair was performed remotely. The contact stated that the dealer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
- Fuel/propulsion system
Purge valve is sticking open when fueling making it to where it take 10 plus minutes to start car after fueling. Worried it will end up causing more issues and possibly cause problems with fuel tank
- Unknown or other
Transmission has gone out after only having the vehicle for 2.5 years. It will cost $10,000 to repair and that is not feasible or right. The mileage is at 74,000 but the warranty expired at 60,000. Ford should be held accountable for building these vehicles with awful transmissions.
- Power train · Power train › Driveline › Differential unit
The contact owns a 2021 Ford Edge. The contact stated that while driving on several occasions and making a turn, there was an abnormal clicking sound coming from underneath the vehicle. The contact added that her husband did donuts continuously and observed the sound. The vehicle was taken to an…
The contact owns a 2021 Ford Edge. The contact stated that while driving on several occasions and making a turn, there was an abnormal clicking sound coming from underneath the vehicle. The contact added that her husband did donuts continuously and observed the sound. The vehicle was taken to an independent mechanic, where it was determined that the sound in the rear axle was coming from the left rear differential. The mechanic stated that the rear differential fluid had been leaking oil for a while and that the rear differential needed to be replaced. The vehicle was not repaired. The contact associated the failure with Manufacturer Recall: 21S02. The manufacturer was notified of the failure. The failure mileage was approximately 68,000.
- Suspension
I am have problem with my axle making a clicking sound the axle the is not safe to drive
- Power train
The contact owns a 2021 Ford Edge. The contact stated that the vehicle was shuddering, and the transmission was slipping while driving approximately 0-50 MPH. No warning lights were illuminated. The transmission fluid was flushed and refilled every 20,000 miles. The local dealer was contacted, but…
The contact owns a 2021 Ford Edge. The contact stated that the vehicle was shuddering, and the transmission was slipping while driving approximately 0-50 MPH. No warning lights were illuminated. The transmission fluid was flushed and refilled every 20,000 miles. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was approximately 80,000.
- Power train
My 2021 Ford Edge has experienced ongoing transmission issues for an extended period including delayed engagement into Reverse, flashing gear indicator lights before Reverse engagement, harsh/jumpy shifting during acceleration and deceleration, and intermittent shuddering. The vehicle previously…
My 2021 Ford Edge has experienced ongoing transmission issues for an extended period including delayed engagement into Reverse, flashing gear indicator lights before Reverse engagement, harsh/jumpy shifting during acceleration and deceleration, and intermittent shuddering. The vehicle previously required a torque converter replacement performed by a Ford dealership, however the symptoms continued after the repair. Today, while driving on the highway, the vehicle experienced repeated loss of power and hesitation while attempting to accelerate and maintain speed. During one highway merge, the vehicle failed to respond normally while accelerating and I was nearly struck by a semi-truck because I could not safely match traffic speed. Shortly afterward, while exiting the highway, the vehicle suddenly jolted violently and began making loud grinding noises accompanied by severe shuddering. The transmission/drivetrain appeared to fail completely, making the vehicle unsafe to continue operating. I stopped driving immediately and had the vehicle towed to the same Ford dealership that previously replaced the torque converter. I am submitting this complaint because the transmission failure created a serious safety hazard involving loss of propulsion at highway speeds, unsafe merging conditions, and risk of collision.
- Power train
Shudder when automatic transmission shifts. Long lag time when vehicle accelerates after throttle is engaged. Can feel and hear knock every time throttle is engaged and disengaged.
- Power train
Transmission has gone out with just over 100,000 and will cost $8,000+ to fix! Vehicle is binding/jerking when trying to drive. Online comments appear to indicate Ford is aware of an issue with this vehicle, seems it was not manufactured properly to begin with and consumers were taken advantage of and left in tough circumstances when it fails.
- Electrical system · Power train · Service brakes
Purchase this vehicle at 30,000 miles have problems with it since day one with the ABS rear brake dragging I've done had two ABS control modules replaced the ABS control pump the torque converter because the brakes are tearing the torque converter out of it from all the strain. It does it…
Purchase this vehicle at 30,000 miles have problems with it since day one with the ABS rear brake dragging I've done had two ABS control modules replaced the ABS control pump the torque converter because the brakes are tearing the torque converter out of it from all the strain. It does it intermittently. All of the repairs have been done through Ford they had to replace the when the brake rotors the calipers brake pads because of how hot the brake system is getting. The brakes will start dragging which will heat up the brake system and they will start putting herself in a bind. Four don't know what's causing it they said they think it could be an electrical issue that's causing the ABS control module to go hay wire and I wasn't getting any codes at all. Except once and it's in Walt's communication that aBS control module a. This problem is going to get myself or my family or your family killed on the roads
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Loss of Motive Power
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine…
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011209"Quality improvements include: -Adds a ""some display features may be temporarily unavailable"" message to the SYNC screen when a SYNC update is installing."
- 11010950Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs. Various vehicles equipped with a 2.7L or a 3.0L gas engine may require a crankshaft bolt replacement during repairs.
- 11010213"Quality improvements include: -Improved error logging and fault recovery for the Battery Health, Wheel Alignment, Wheel Vibration, and Key off load monitors."
- 11010210Quality improvements include: - Improved networking quality for software updates. -Allows vehicle access during OTA update. - Minor ECG updates - not customer facing. - Improved connectivity - Reduces Key Off Load battery drain.
- 11009919Quality improvements include: -Telematics Control Unit mantains its country code after updates -Ensures factory software image cannot be loaded onto the Telematics Control Unit once a production software has been loaded -Stolen Vehicle Service enhancement
- 11009445Some 2018-2024 F150/Edge, 2018 MKX, 2019-2023 Nautilus, 2020-2025 Explorer/Aviator, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L EcoBoost or a 3.0L EcoBoost engine may exhibit an engine oil leak from the crankshaft rear seal with retaining plate.
- 11009439Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
- 11008948While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
- 11007916Unable To Update APIM, TCU Or GWM With FDRS And USB Drive - TSB 22-2404 Module Recovery App No Longer Available on FDRS
- 11001112Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
- 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
- 10253552Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
- 10251952For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
- 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
- 10251455This TSB supersedes TSB 23-2049 to update the parts list. Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
- 10250839Some 2021-2022 Edge vehicles may exhibit an inoperative Sirius satellite radio with audio control module (ACM) DTC B1A89:13. This may be due to the accessory protocol interface module (APIM) configuration. To correct the concern, download and run the APIM Programmable Module Installation (PMI) application. When the application asks Is The Original Module Installed, select NO. Once the programming completes, clear the DTCs. For claiming, use causal part 14G670 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10247526Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
- 10245389Some 2019-2021 Edge/Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a noise from the rear of the vehicle while approaching the vehicle or prior to starting engine. This may be due to the rear drive unit (RDU) actuator learning process. Reprogram the software in the AWD module to minimize the noise using the latest software level of the appropriate Ford diagnostic scan tool. If no other concerns or symptoms are present, further diagnosis or repairs are not recommended. For claiming, use causal part 4000 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10245384Some 2019-2021 Edge/Nautilus vehicles equipped with all-wheel drive (AWD) may exhibit a noise/vibration/chatter/shudder/grind/bind from the rear of the vehicle during low speed turning events. To correct the condition, reprogram the AWD module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use casual part RECAL and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10245258Some 2019-2023 Edge/Nautilus and 2022-2023 Maverick vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events. This may be due to fluid contamination in the rear drive unit (RDU). Drain and refill the RDU, refer to Workshop Manual Section (WSM) 205-02. Drive for 5 miles (8 km) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with normal WSM diagnostics. For claiming, use causal part 4000.
- 10241981"Software Update 4 P4 for 2021- 2023 Edge vehicles is now available. Quality Improvements include: - Various Apple Carplay quality improvements "
- 10241627In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
- 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
- 10240577Some 2019-2023 Edge/Nautilus, 2020-2023 Escape/Corsair, 2021-2023 Bronco Sport, 2022-2023 Maverick vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events. This may be due to fluid contamination in the rear drive unit (RDU). Drain and refill the RDU, refer to Workshop Manual Section (WSM) 205-02. Drive for 5 miles (8 km) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with normal WSM diagnostics. For claiming, use base (4000) causal part.
- 10239099Some 2020-2021 Escape built on/before 23-Nov-2021, 2021 F-150 built on/before 08-Oct-2021, 2021 Mustang Mach-E built on/before 29-Mar-2021, 2021 Expedition built on/before 05-Aug-2021, 2021 Explorer built on/before 27-Sep-2021 and 2020-2022 Edge may exhibit a concern of the audio system does not power on, no sound from audio speakers, chimes default to coming through the instrument cluster, no communication with audio control module (ACM) or digital signal processor (DSP) module, and/or diagnostic trouble code (DTC) U0184, U0237 and/or U0238. To correct the condition, perform a hard reset of the DSP by disconnecting the 12-volt battery. Reprogram the DSP module using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18B849 and any applicable labor operations in Section 10 of the Service Labor Time Standards Manual.
- 10238727Software Update 4 P3 for 2021- 2022 Edge vehicles is now available. Quality improvements include: - Key fob access to vehicle during update. - Pre-conditioning pop up alerts.
- 10236688Some 2021-2023 Ford and Lincoln vehicles equipped with a 2.7L or 3.0L engine may exhibit an upper engine thump/knock noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.
- 10236023Some 2021-2023 F-150/Mustang Mach-E/Edge vehicles may exhibit a concern of Android Auto unable to wirelessly connect and/or Android phones rebooting when connected to the vehicle via USB. This is due to a concern with the Google application on the customers device. Google has released a fix for these concerns. For Android phones not connecting wirelessly, request that the customer update their Android Auto version to 6.1 or later. For customers who's Android phone reboots when connected via USB, request that the customer update their Chrome application to 88.0.4324.181 or later. The customers service provider should be able to assist customers having difficulty updating their device. This is not a warrantable repair.
- 10235153For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
- 10233656Some 2021-2022 Ford and Lincoln vehicles equipped with SYNC 4 may experience an error message during the gateway module (GWM) software update application which states Procedure Unsuccessful- GetConfigDataFromGIVIS. This may be the result of a server related concern. To correct the condition, download and run the Ford Diagnosis and Repair System (FDRS) application GWM-Read the Gateway Module A (GWM) Configuration Data application. When the application completes, refresh and re-attempt the GWM-Gateway Module A (GWM) Software Update application. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10233584Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
- 10232482Some 2019-2023 Edge/Nautilus vehicles equipped with a 2.0L engine may exhibit a repeat block heater failure. This may be caused by air in the engine cooling system. The WSM replacement procedure has been updated to include the Engine Cooling System Draining, Vacuum Filling and Bleeding procedure found in Section 303-03A Engine Cooling - 2.0L EcoBoost (184kW/250PS) MI4, General Procedures as the final step. The block heater should not be tested unless all the air has been removed from the engine cooling system following this procedure.
- 10228876Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
- 10226953Certain 2021 Model Year Mach-E, F-150, Bronco, Edge, Nautilus vehicles Electronic Control Module Recovery REASON FOR THIS SUPPLEMENT Program Terms: The program expiration date was incorrectly shown as October 31. 2022. The correct date is April 30, 2023. Affected Vehicles: The build dates were updated. Verbiage added to indicate the population will increase as more vehicles with modules needing recovery are identified. Service Action: Verbiage added to indicate the population will increase as more vehicles with modules needing recovery are identified. Owner Notification Mailing Schedule: Verbiage added on mailing owner letters to additional owners as they are identified. Owner Refund Expiration Date: The owner refund expiration date was incorrectly shown as May 27, 2022. The correct date is April 30, 2023.
- 10226935This article supersedes TSB 22-2062 to update the Issue, Action and Service Procedure. Some 2021-2022 Edge/Nautilus vehicles may experience one or more of the following symptoms: Inoperative Front Camera if the camera system button is pressed once the vehicle is below the speed threshold of 6 mph (10 km/h) (Edge Only), Android Auto connection concerns, Apple CarPlay connection concerns, center display screen freezing/locking up, windows media audio (WMA) files not playing properly from a universal serial bus (USB) device, intermittent blank center display screen, Bluetooth connectivity concerns, incorrect Owner's Manual language for French, frozen or delayed touch response for center display screen. This may be due to the software in the accessory protocol interface module (APIM). To correct the condition, follow the Service Procedure to reprogram the APIM. NOTE: The APIM software update that addresses the symptom listed in this article may have been delivered over-the-air (OTA) via Ford Power-Up software updates to connected vehicles that have automatic updates enabled through the center display screen
- 10226775This article supersedes TSB 22-2150 and SSM 50970 to update the Service Procedure. For some 2021 Mustang Mach-E, F-150, Edge, Nautilus and Bronco vehicles technicians may experience the inability to update the accessory protocol interface module (APIM), telematics control unit (TCU) or gateway module (GWM) using the Ford Diagnosis and Repair System (FDRS) and Universal Serial Bus (USB) drive. The PTS OTA Dashboard on vehicles with this condition may also display multiple APIM and/or TCU updates have failed, and/or a no OTA history message. In addition, on vehicles with this condition, the customer may have reported experiencing a Ford Power-Up software update failure message via the vehicle display and/or FordPass/LincolnWay. This may be due to an internal software error. To correct this condition, follow the Service Procedure to update and/or recover the APIM/TCU. Note: Only 10% of vehicles may require this procedure.
- 10225444Some 2019-2022 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to stuck internal components of the variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
- 10225439Some 2021 Edge vehicles which have received an APIM software update may experience a concern with Sirius radio being inoperative. This will be accompanied by ACM diagnostic trouble code (DTC) B1A89:13 for the satellite antenna. To correct this condition, download and run the APIM Programmable Module Installation (PMI) application using the latest software level of the Ford Diagnosis and Repair System (FDRS). When the PMI asks, Is The Original Module Installed?, select NO. When the PMI completes, perform an ALL CMDTC test and clear all DTCs. For claiming, use causal part 14G670 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
- 10222788Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
- 10222786Some 2021-2022 Bronco Sport 1.5L, 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2022 Maverick vehicles may exhibit an illuminated AWD warning indicator or fault message with diagnostic trouble code (DTC) C0095:71/:19 stored in the all wheel drive (AWD) module. Some 2021-2022 Bronco Sport 2.0L may exhibit an illuminated AWD warning indicator or fault message with DTC C05D9:71, C05E8:71, C05D8:19 and/or C05E7:19 stored in the AWD module. This may be due to a rear drive unit (RDU) motor magnet ring misalignment. RDU assembly replacement is no longer required. To correct the condition, replace the RDU motor which is now available separately for service. Refer to Workshop Manual, Section 205-02 for diagnosis and repair procedures. For claiming use causal part 4C210 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Every Ford Edge model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.