2015 Mazda MAZDA3
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mazda › MAZDA3 › 2015
These records cover every 2015 Mazda MAZDA3. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2015 Mazda MAZDA3. Newest first.
Mazda North American Operations (Mazda) is recalling certain 2014-2018 Mazda3 and 2016-2021 CX-3 vehicles. The rearview camera image may not display properly by showing a flickering or distorted image.
Risk and remedy
Risk
A rearview camera that does not display properly can reduce the driver's rear view, increasing the risk of a crash or injury.
Remedy
Dealers will inspect and replace the rearview camera, as necessary. In addition, dealers will install a wiring harness fastening seal. All repairs will be performed free of charge. Interim notification letters, notifying owners of the safety risk, were mailed September 13, 2023. Final owner letters for affected models and model years in the states of CT, MA, MD, NJ, NY, PA and VA were mailed August 14, 2024. The remaining owner notification letters will be mailed at a future date, anticipated on or before May 1, 2025. Owners may contact Mazda customer service at 1-800-222-5500, Option 6. Mazda's number for this recall is 6023G.
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda6 and 2014-2016 Mazda3 vehicles. Water could possibly enter the brake caliper causing the parking brake actuator shaft to corrode and possibly bind.
Risk and remedy
Risk
If the parking brake actuator shaft binds, the parking brake may not engage or disengage fully. If the parking brake does not engage properly, the vehicle may move unexpectedly if it is parked on a slope, increasing the risk of a crash.
Remedy
Mazda will notify owners, and dealers will check the parking brake actuator shafts, replacing any that are corroded, free of charge. Remedy parts are currently unavailable. Interim notices informing owners of the safety risk were mailed August 24, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1217F.
Mazda Motors North American Operations (Mazda) is recalling certain model year 2014-2016 Mazda3 vehicles manufactured January 4, 2014, to September 18, 2015. The fuel tank of the affected vehicles may have been improperly handled during manufacturing and, as a result, the welded attachment of the Inlet Check Valve (ICV) may fail and allow fuel to leak.
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy
Mazda will notify owners, and depending on the tank lot number, dealers will inspect the ICV weld, replacing the fuel tank, as necessary, free of charge. The recall began November 1, 2016. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 0116I.
Mazda North American Operations (Mazda) is recalling certain model year 2015-2016 Mazda3 vehicles manufactured May 21, 2015, to August 25, 2015. The affected vehicles are equipped with a fuel tank with a shut-off valve that can allow fuel to enter into the fuel tank emissions systems. If enough fuel enters the emission system it may leak out onto the…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire. An engine that stalls increases the risk of a crash.
Remedy
Mazda will notify owners, and dealers will inspect the vehicle's fuel shut-off valve. As needed, the fuel shut-off valve and the affected fuel tank emissions system components will be replaced, free of charge. The recall began on October 20, 2015. Owners are advised not to drive their vehicle until the repairs have been completed. Mazda will provide rental cars until that time. Owners may contact the Mazda Customer Experience Center at 1-800- 222-5500, option #6. Mazda's number for this recall is 8615J.
Owner complaints
130 complaints8 involved a crash2 involved a fire9 injuries
What owners report most
Latest complaints
- Back over prevention › Sensing system › Camera
The contact owns a 2015 Mazda Mazda3. The contact stated that while driving at various speeds, or while attempting to reverse, the rear camera flashed on and off for approximately five minutes and then started working as intended. No warning light was illuminated. The vehicle was repaired under the…
The contact owns a 2015 Mazda Mazda3. The contact stated that while driving at various speeds, or while attempting to reverse, the rear camera flashed on and off for approximately five minutes and then started working as intended. No warning light was illuminated. The vehicle was repaired under the NHTSA Campaign Number: 23V487000 (BACK OVER PREVENTION) by the owner of the vehicle; however, the fix failed to repair the vehicle. The contact stated that the failure had occurred after the recall repair was performed. The manufacturer was not notified of the failure. The failure mileage was 180,000.
- Fuel/propulsion system
While parked on a slight downhill grade, gasoline started leaking and created a significant puddle on the ground. No warning lamps, messages or other symptoms. An independent service center ran numerous tests over two days, including a smoke test. Diagnosis: There is a hole in top section of fuel…
While parked on a slight downhill grade, gasoline started leaking and created a significant puddle on the ground. No warning lamps, messages or other symptoms. An independent service center ran numerous tests over two days, including a smoke test. Diagnosis: There is a hole in top section of fuel tank and the fuel tank needs replaced. Recommendation was to not drive vehicle with fuel tank over half full. Due to the potential of leaking fuel in the presence of a hot ignition source increasing the risk of fire, driving the vehicle long distance with defective fuel tank appears to represent an unreasonable safety risk. Unfortunately, the vehicle is currently 300 miles from home. Mazda’s Mexican-made plastic fuel tank specifically required for our vehicle’s VIN is not currently available. (Mazda makes a similar metal fuel tank in [XXX] which will not fit.) Mazda has an estimated three-month backlog in [XXX] for the fuel tank. Still awaiting repair due to lack of availability of the appropriate fuel tank. Major safety recall NHTSA 16V684000 for the 2015 Mazda3 addresses a manufacturing defect where a fuel tank weld could fail, leading to fuel leaks and a potential fire. Recall is for vehicles produced between 12/4/13 – 9/18/15. Our vehicle was manufactured 02/2015 in [XXX] . However, recall is limited to three specific series of VINs and our vehicle falls in the gap between subject VIN ranges. A recent NHTSA complaint XXX (1/27/26) has the same issue: fuel tank leak, but not within range of recall VINs. It seems that the list of affected VINs included in recall 16V684000 should be expanded to include additional Mexican manufactured vehicles potentially with the same issue. Or create a new recall. Having a hole in the top of a plastic fuel tank securely mounted to the vehicle is unexpected through normal wear and tear. Any fuel leakage increases the risk of fire. NHTSA should investigate if this is due to a defect in Mazda’s manufacturing process. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFOR
- Fuel/propulsion system
Fuel leaking out of top of tank. Took car to two different shops. They both told me about a recall on the gas tank. They did every test possible and replaced O ring. Even did smoke evap system test. Tank still leaks from the top when full. They said the tank needs replaced. There is a recall for the year make and model but not my VIN?
- Service brakes
Description On 12-15-2025, in 18°F weather, the vehicle was parked on a residential sloped driveway with the manual parking brake fully engaged. While the driver was outside the vehicle, the parking brake system failed to hold the car’s weight. The vehicle rolled backward, crashed through a wooden…
Description On 12-15-2025, in 18°F weather, the vehicle was parked on a residential sloped driveway with the manual parking brake fully engaged. While the driver was outside the vehicle, the parking brake system failed to hold the car’s weight. The vehicle rolled backward, crashed through a wooden railing, teetering on a 4-foot retaining wall, and came to rest over a culvert. Two young children were inside the vehicle at the time of the failure. Component Failure & Availability: The manual parking brake system failed to provide sufficient holding force to secure the vehicle. The rear brake calipers are currently available for inspection. Safety Risk: The safety of the two children inside the vehicle was put at extreme risk due to the unexpected movement of the car. This failure matches the exact conditions and consequences described in Safety Recall 1217F (NHTSA Campaign 17V-393), which states that "unexpected movement of the vehicle if parked on a slope" increases the risk of a collision. Reproducibility & Confirmation: The failure occurred under the specific environmental triggers (cold temperature and slope) identified in the manufacturer's own safety recall documentation. However, the manufacturer has officially refused to authorize the internal teardown of the actuator shafts—the only diagnostic method capable of verifying the rust and sliding resistance that causes this loss of holding force. Inspections: The vehicle has been visually inspected by an authorized dealership and insurance representatives. The manufacturer has declined the necessary internal mechanical diagnostics to verify the internal defect. Warning Symptoms: There were no warning lamps, messages, or symptoms prior to the failure. The parking brake felt fully engaged at the time the vehicle was parked.
- Engine · Fuel/propulsion system
Catalytic converter keeps giving me check engine
- Unknown or other
I had purchased a car through Facebook Marketplace after talking to the seller and seeing a CarFax report on the car we decided to purchase it. After coming home the following day I look closer at the documents and realized the CarFax did not match the VIN of the car I purchased. After looking up the CarFax with the VIN on the car I purchased I saw that the person who sold me the car had rolled back the odometer.
- Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (BACK OVER PREVENTION). However, the dealer refused to complete the recall repairs due to the vehicle having a Salvage Title. The contact stated that the rearview camera displayed a black…
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (BACK OVER PREVENTION). However, the dealer refused to complete the recall repairs due to the vehicle having a Salvage Title. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. The manufacturer was made aware of the issue and referred the contact back to the dealer. The vehicle remained unrepaired. The failure mileage was approximately 86,000.
- Parking brake
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 17V393000 (Parking Brake); and would like to be removed from the recall distribution list. The local dealer and manufacturer were not contacted.
- Unknown or other
The vehicle automator mileage was changed. The original mileage reading is over 200,000 mi. While the dashboard mileage only reads 90,780 mi. I was unaware of this until I went to the DMV to do a title transfer. The private seller is now nowhere to be found from Facebook marketplace and has blocked me but I do have receipts of everything
- Electrical system
The Infotainment System will randomly change radio stations while driving, or start scanning through the various system menus, and on at least in one case, started randomly making phone calls from a connected phone. This creates a major distraction while driving. This has been looked at by the dealership and would cost $1500 for the system repair. I understand that this is a known problem.
- Power train
1. Automatic transmission suffered a catastrophic failure during operation. Transmission was discarded by Bountiful Mazda, Utah. 2. Both other and I were at risk as the vehicle could not be controlled. 3. I read similar findings on Social Media posts. 4. Bountiful Mazda confirmed metal shavings in…
1. Automatic transmission suffered a catastrophic failure during operation. Transmission was discarded by Bountiful Mazda, Utah. 2. Both other and I were at risk as the vehicle could not be controlled. 3. I read similar findings on Social Media posts. 4. Bountiful Mazda confirmed metal shavings in the drain trans fluid. 5. No prior warning on car instrumentation, or while driving, or on prior inspection by Cardinaleway Mazda, Gilbert, AZ 6. Neither Mazda USA (Mfr) nor Protective Asset Protection have taken responsibility for the initial equipment failure nor reimbursement through the extended service contract even with extenuating circumstances for late notification. I can provide copies of additional relevant material.
- Fuel/propulsion system
Since the middle of 2023 I have noticed a gas fume smell both inside and outside of my 2015 Mazda Mazda3 after I fill my gas tank to full. This smell persists up until I use about a half tank of gas or slightly less. I do not top my gas tank off and stop filling when the automatic gas pump stops.…
Since the middle of 2023 I have noticed a gas fume smell both inside and outside of my 2015 Mazda Mazda3 after I fill my gas tank to full. This smell persists up until I use about a half tank of gas or slightly less. I do not top my gas tank off and stop filling when the automatic gas pump stops. There are no visible leaks on or around the gas tank or below the vehicle, and there are no noticeable cracks around the gas tank, valves, lines, etc. Additionally, there are no warning lights present on my dashboard or any codes.
- Electrical system
The Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of the touch screen may be corroded due to moisture, which may adhere on the lens of the touch screen during the cleaning process at…
The Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of the touch screen may be corroded due to moisture, which may adhere on the lens of the touch screen during the cleaning process at the plant. The corrosion may allow the electrostatic capacity to vary without any input, causing the malfunction of the touch screen.
- Electrical system
Mazda call this “ghost touch” it happens when the screen starts to act up like crazy, jumping from different audio sources, Bluetooth lose connection, making unwanted phone calls. Almost like a ghost is touching the screen over and over again.
- Back over prevention › Sensing system › Camera
On Thursday October 9th I drove to work at 11pm and parked my car. I backed up into my space using my back-up camera as I had always did since I had purchased my car in 2019. The next morning when I got home and put my car in reverse to back into my space, I noticed that the back-up camera did not…
On Thursday October 9th I drove to work at 11pm and parked my car. I backed up into my space using my back-up camera as I had always did since I had purchased my car in 2019. The next morning when I got home and put my car in reverse to back into my space, I noticed that the back-up camera did not come on. The radio continued to play on the screen, but in never switched over to the camera so that I could use this component to park. After trying several times to try to figure out what the issue was I gave up. I had an appointment that same morning, so I parked my car and came back about an hour later to leave and started my car, pulled out of my space, then put my car in reverse and the camera was back up and running again. I found this to be strange. Most likely this will happen again. I googled/researched this to see if there was a recall for this issue in this make and model and came across a few articles where others had the same or similar complaints. So it all lead me here. It seems as if there is a malfunction in these cameras, if it is happening to others, and happened to me, then it's happening. So what's happening...is my question? Why are these camera not recalled? Do we wait until it shuts down in the middle of us backing up or what? What's next? Can I get someone at Mazda to look at my camera, and replace it? Or is this something I have to live with? I should not have to, neither should I have to pay some outrageous price to get it replace on my own dime. There is definitely an issue with this camera in this make and model. So is anyone going to be fair and do something about this, or wait until there is an accident behind it? If it's a defect in the product, just simply replace it.
- Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated…
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the back-up camera screen image was flickering and became distorted while reversing. The cause of the failure was not determined. The failure mileage was 60,000. VIN tool confirms parts not available.
- Unknown or other
I am filing this complaint regarding existing Manufacturer Recall Number 6023G (NHTSA Recall Number 23V-487). This recall has been posted since Jul 14, 2023 and the manufacturer has failed to remedy the recall in a timely manner. The remedy is noted on the recall page: "If inspections verify there…
I am filing this complaint regarding existing Manufacturer Recall Number 6023G (NHTSA Recall Number 23V-487). This recall has been posted since Jul 14, 2023 and the manufacturer has failed to remedy the recall in a timely manner. The remedy is noted on the recall page: "If inspections verify there is image distortion or flickering, the rearview camera will be replaced with a new part and a wiring harness fastening seal will be added." However, the manufacturer continues to state that the remedy is not yet available.
- Lane departure › Blind spot detection
The contact owns a 2015 Mazda Mazda3. The contact stated that occasionally while the vehicle was shifted into reverse, the review camera image would not display on the digital screen. In addition, the contact stated that the image looked distorted. The contact received a notification of 23V487000…
The contact owns a 2015 Mazda Mazda3. The contact stated that occasionally while the vehicle was shifted into reverse, the review camera image would not display on the digital screen. In addition, the contact stated that the image looked distorted. The contact received a notification of 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 85,000.
- Unknown or other
The problem I have is with my rearview camera, as described in Manufacturer Recall Number 6023G / NHTSA Recall Number 23V-487. This problem has existed since I purchased the car in November 2022. The recall was announced on 7/14/23. Mazda has failed to provide a remedy. Dealers report that they…
The problem I have is with my rearview camera, as described in Manufacturer Recall Number 6023G / NHTSA Recall Number 23V-487. This problem has existed since I purchased the car in November 2022. The recall was announced on 7/14/23. Mazda has failed to provide a remedy. Dealers report that they don't have the parts needed to make the repair and that no remedy has been provided by Mazda. It is meaningless to have a recall if the manufacturer doesn't fix the problem. This is a serious safety issue as when the problem occurs, it is not possible to see behind the car via the camera/screen.
- Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated while reversing, the rearview camera image failed to display. The local dealer was…
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated while reversing, the rearview camera image failed to display. The local dealer was notified of the failure, but the vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure, but no assistance was provided. The failure mileage was approximately 82,000. VIN tool confirms parts not available.
- Fuel/propulsion system
Started smelling gas fumes several weeks ago after fill ups at the gas station. Took to my mechanic who diagnosed a fuel tank leak due to rust. No warning lights present. No fuel on the ground or fumes within the cabin.
- Unknown or other
The infotainment system sometimes has "ghost touches" where random buttons on the screen are pressed without a physical press. This is dangerous because it is extremely distracting to the driver. It often changes songs or calls a random person on my phone contact list. This requires me to quickly…
The infotainment system sometimes has "ghost touches" where random buttons on the screen are pressed without a physical press. This is dangerous because it is extremely distracting to the driver. It often changes songs or calls a random person on my phone contact list. This requires me to quickly and constantly press the "back" button for the infotainment system to prevent it from placing a call. This forces my attention and hands away from the core task of driving while the car is in motion.
- Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rearview camera image was distorted, blank or failed to…
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rearview camera image was distorted, blank or failed to activate as needed. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 63,000. VIN tool confirms parts not available.
- Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact stated that while reversing, the rear-view camera image was distorted, black, and failed to appear on the center display. The vehicle was taken to the local dealer, where an unknown software was reprogrammed; however, the failure persisted. The…
The contact owns a 2015 Mazda Mazda3. The contact stated that while reversing, the rear-view camera image was distorted, black, and failed to appear on the center display. The vehicle was taken to the local dealer, where an unknown software was reprogrammed; however, the failure persisted. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 53,953. VIN tool confirms parts not available.
- Unknown or other
Mazda opened a recall on the rearview camera not working properly almost one year ago and still has not supplied a remedy. REference: 6023G | Jul 14, 2023 #23V-487
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
- 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
- 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11008577Some customers may complain about scratches on the instrument cluster lens.
- 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
- 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
- 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
- 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
- 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
- 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
- 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10254188Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254187Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
- 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 10251368Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10243568Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10243551Service bulletin 09-031/20 issued on 09/21/20 IS no longer valid. It IS superceded by recall 6023g (2014-2018 mazda3 and 2016-2021 CX-3 - rearview image may not display properly).
- 10241637Some customers may complain about scratches on the instrument cluster lens.
- 10240496Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10240431Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
- 10240427Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
- 10238697Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
- 10238695Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
- 10238663Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
- 10237217Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 10237216If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10237215Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10237199Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
Every Mazda MAZDA3 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.