2016 Mazda MAZDA3
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mazda › MAZDA3 › 2016
These records cover every 2016 Mazda MAZDA3. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
6 recalls name the 2016 Mazda MAZDA3. Newest first.
Mazda North American Operations (Mazda) is recalling certain 2014-2018 Mazda3 and 2016-2021 CX-3 vehicles. The rearview camera image may not display properly by showing a flickering or distorted image.
Risk and remedy
Risk
A rearview camera that does not display properly can reduce the driver's rear view, increasing the risk of a crash or injury.
Remedy
Dealers will inspect and replace the rearview camera, as necessary. In addition, dealers will install a wiring harness fastening seal. All repairs will be performed free of charge. Interim notification letters, notifying owners of the safety risk, were mailed September 13, 2023. Final owner letters for affected models and model years in the states of CT, MA, MD, NJ, NY, PA and VA were mailed August 14, 2024. The remaining owner notification letters will be mailed at a future date, anticipated on or before May 1, 2025. Owners may contact Mazda customer service at 1-800-222-5500, Option 6. Mazda's number for this recall is 6023G.
Mazda North American Operations (Mazda) is recalling certain 2016-2018 Mazda3 vehicles. A defective windshield wiper relay may cause the windshield wipers to become inoperative, reducing the driver's visibility.
Risk and remedy
Risk
Reduced visibility while driving can increase the risk of crash.
Remedy
Mazda will notify owners, and dealers will replace the front body control module with a new module which uses an improved wiper relay design, free of charge. The recall began May 7, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 3219D.
Mazda North American Operations (Mazda) is recalling certain 2014-2015 Mazda6 and 2014-2016 Mazda3 vehicles. Water could possibly enter the brake caliper causing the parking brake actuator shaft to corrode and possibly bind.
Risk and remedy
Risk
If the parking brake actuator shaft binds, the parking brake may not engage or disengage fully. If the parking brake does not engage properly, the vehicle may move unexpectedly if it is parked on a slope, increasing the risk of a crash.
Remedy
Mazda will notify owners, and dealers will check the parking brake actuator shafts, replacing any that are corroded, free of charge. Remedy parts are currently unavailable. Interim notices informing owners of the safety risk were mailed August 24, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1217F.
Mazda North American Operations (Mazda) is recalling certain model year 2016 Mazda3 vehicles manufactured September 24, 2015, to October 16, 2015. During manufacturing, the fuel tanks for the affected vehicles may have deformed, resulting in a fuel leak from the recirculation pipe welded connection.
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy
Mazda will notify owners, and depending on the tank lot number, dealers will inspect the recirculation pipe weld, replacing the fuel tank, as necessary, free of charge. The recall began November 1, 2016. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 0216I.
Mazda Motors North American Operations (Mazda) is recalling certain model year 2014-2016 Mazda3 vehicles manufactured January 4, 2014, to September 18, 2015. The fuel tank of the affected vehicles may have been improperly handled during manufacturing and, as a result, the welded attachment of the Inlet Check Valve (ICV) may fail and allow fuel to leak.
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy
Mazda will notify owners, and depending on the tank lot number, dealers will inspect the ICV weld, replacing the fuel tank, as necessary, free of charge. The recall began November 1, 2016. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 0116I.
Mazda North American Operations (Mazda) is recalling certain model year 2015-2016 Mazda3 vehicles manufactured May 21, 2015, to August 25, 2015. The affected vehicles are equipped with a fuel tank with a shut-off valve that can allow fuel to enter into the fuel tank emissions systems. If enough fuel enters the emission system it may leak out onto the…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source increases the risk of a fire. An engine that stalls increases the risk of a crash.
Remedy
Mazda will notify owners, and dealers will inspect the vehicle's fuel shut-off valve. As needed, the fuel shut-off valve and the affected fuel tank emissions system components will be replaced, free of charge. The recall began on October 20, 2015. Owners are advised not to drive their vehicle until the repairs have been completed. Mazda will provide rental cars until that time. Owners may contact the Mazda Customer Experience Center at 1-800- 222-5500, option #6. Mazda's number for this recall is 8615J.
Owner complaints
104 complaints7 involved a crash1 involved a fire5 injuries
What owners report most
Latest complaints
- Service brakes
After speaking with Mazda customer support, the sales department at Germain Mazda of Columbus, and the service department of Mazda Columbus, I have come to learn that in response to recall 1217F | XXX17V-393, the dealership that performed the recall only performed an inspection with no repair or…
After speaking with Mazda customer support, the sales department at Germain Mazda of Columbus, and the service department of Mazda Columbus, I have come to learn that in response to recall 1217F | XXX17V-393, the dealership that performed the recall only performed an inspection with no repair or replacement made to the vehicle. The recall notice does not indicate that this is an option. Please see excerpt below: "Your Mazda dealer will check the parking brake actuator shafts inside the left and right rear brake calipers. If the actuator shaft is found to be rusted, the brake caliper assembly will be replaced with a modified one. If no rust is found on the actuator shaft, the protective boot will be replaced with a modified one. The inspection and repair will be performed at no cost to you." (from [XXX]) From my conversations with the three departments, no work was done for this recall on my vehicle beyond an inspection finding that the recalled component is still working. Additionally, I was not informed of this recall or that no repairs or replacement were made in response to the recall despite it being closed as completed when I purchased the vehicle. Coming out of this previous Winter, my parking brake quickly began to fail and became useless by Spring of this year. I am on the phone with Mazda customer service again now who once again confirmed ONLY an inspection was performed despite the language in the recall notice. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Steering
The contact owns a 2016 Mazda Mazda3.The contact stated that while driving at various speeds, the contact stated that the vehicle's steering wheel would fail to operate as needed. The contact stated that an abnormal, clunking noise would emit from the steering wheel while turning at various speeds.…
The contact owns a 2016 Mazda Mazda3.The contact stated that while driving at various speeds, the contact stated that the vehicle's steering wheel would fail to operate as needed. The contact stated that an abnormal, clunking noise would emit from the steering wheel while turning at various speeds. The contact also stated that the steering wheel felt loose while driving at high speeds, fearing that he would lose control of the vehicle if he did not firmly grip the steering wheel. The contact had taken the vehicle to a dealer where they acknowledged that the heard the noise coming from the vehicle; however, they could not duplicate or diagnose the failure. The manufacturer was notified of the failure but offered no assistance. The vehicle was not repaired. the failure mileage was approximately 117,000.
- Electrical system
The contact owns a 2016 Mazda Mazda3. The contact stated that while driving and while starting the vehicle, the instrument cluster was inoperable. The contact also stated that the instrument cluster screen was peeling, and critical information for the vehicle was not displayed. Additionally, the…
The contact owns a 2016 Mazda Mazda3. The contact stated that while driving and while starting the vehicle, the instrument cluster was inoperable. The contact also stated that the instrument cluster screen was peeling, and critical information for the vehicle was not displayed. Additionally, the infotainment system became intermittently inoperable due to the failure. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The contact expressed concerns that the inoperable instrument cluster created a hazardous and unsafe condition due to the complete loss of instrument panel functionality. The approximate failure mileage was 142,000.
- Unknown or other
The “spidering” on the infotainment screen is spidering making it hard to see when in reverse.
- Power train
I am writing to formally report a serious safety issue with my 2016 Mazda 3 manual transmission, which experienced a sudden and complete clutch failure at less 60,000 miles — without any warning lights or diagnostic alerts. I am deeply concerned that: •There was no dashboard warning, even as the…
I am writing to formally report a serious safety issue with my 2016 Mazda 3 manual transmission, which experienced a sudden and complete clutch failure at less 60,000 miles — without any warning lights or diagnostic alerts. I am deeply concerned that: •There was no dashboard warning, even as the clutch system failed •The gear indicator was inaccurate in prior days, which may have been an early sign of failure •There was no protection mechanism to prevent complete drivetrain failure during normal use.
- Unknown or other
The "Infotainment System" is activating itself and cycling through various options when I slow down or stop. It calls random numbers and changes settings on the system. It is distracting and dangerous. This is a known "ghost touch" problem for this model of vehicle, but the Mazda dealer I contacted in Knoxville, TN said it would cost nearly $300 to repair the problem (by replacing the entire system).
- Unknown or other
Mazda supposedly repaired/replaced the backup camera issue under the recall. However, within one day it was doing the same thing again...the screen dims or flickers off when backing up the car. I told Mazda about that and they said I need a new screen, which would not be covered under the recall. This is a safety hazard that they should be required to address.
- Seat belts
The contact owns a 2016 Mazda Mazda3. The contact stated that while the vehicle was parked, the driver’s side seat belt became inoperable. The contact stated that the seat belt latch failed to function properly. The vehicle was taken to the dealer but was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 60,000.
- Unknown or other
The 2014 Mazda3 I own has a known "Mazda Connect Touch Screen Concern" in August 2019 in which the Mazda Connect touch screen does not accept touch commands in part of the screen. I called Mazda and they said there are not any recalls for this but they did acknowledge this was an issue.
- Parking brake
The contact owns a 2016 Mazda Mazda3. The contact stated while the vehicle was parked, the parking brake became firm and failed to engage as needed, causing the rear passenger’s side brake pads to not respond as needed after the vehicle was repaired under NHTSA Campaign Number: 17V393000 (PARKING…
The contact owns a 2016 Mazda Mazda3. The contact stated while the vehicle was parked, the parking brake became firm and failed to engage as needed, causing the rear passenger’s side brake pads to not respond as needed after the vehicle was repaired under NHTSA Campaign Number: 17V393000 (PARKING BRAKE). The contact stated that the recall repair failed to fix the vehicle. There was no warning light illuminated. The contact checked the temperature of the brakes and noticed that the brakes were hotter than normal. A dealer was contacted. The vehicle was towed to the dealer where it was diagnosed that the parking brake actuator was rusted on the inside. The vehicle was not repaired. The manufacturer was notified of the failure and opened a case. The failure mileage was 188,900.
- Electrical system
When I checked for recall information 2 recalls were listed under my car's vin #: Recall #1: 3219D with Closed status. Recall #2: 6023G is listed as Active. But, when I tried to schedule a repair for the active recall, the manufacturing website ONLY listed the "closed" recall (3219D) was listed as available for repair, which is bizarre. Please see the attached screenshot of the website. Thanks.
- Unknown or other
I am now experiencing the problems outlined in [XXX] approximately 18 months after the extended warranty period has ended for me. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Back over prevention › Sensing system › Camera
My 2016 Mazda 3 has had a faulty rearview camera, computerized controls, and monitor display screen for over 2 years now. I am not sure if there is a problem with the electrical system because I have lost the ability to turn on the navigation function, the stereo function, and to see the vehicle…
My 2016 Mazda 3 has had a faulty rearview camera, computerized controls, and monitor display screen for over 2 years now. I am not sure if there is a problem with the electrical system because I have lost the ability to turn on the navigation function, the stereo function, and to see the vehicle maintenance information with non-functioning electrical controls and display screen. Sometimes the monitor display would show a blank screen or a fuzzy screen which is a safety hazard especially when I'm driving my vehicle in reverse and could potentially cause an accident. There has been a recall on the rearview camera since July 2023. I have contacted the Mazda dealership multiple times, and they have repeatedly said that the rearview camera parts are still not available. This is unacceptable because it seriously compromises my safety and the safety of others if I cannot safely back up my vehicle when driving due to the faulty rearview camera, computerized controls and monitor display screen. There should also be a recall on the computerized controls and monitor display screen.
- Back over prevention
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the rearview camera image was distorted or failed to display an image while…
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that the rearview camera image was distorted or failed to display an image while reversing. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 60,000. Parts distribution disconnect.
- Electrical system
NHTSA Recall # 23V-487 Manufacturer Recall # 6023G issued July 14, 2023 After repeated phone calls to the Manufacturer and the Mazda Dealership, the recall has not been fixed. I have been told that the parts are not available. As of this date, 16 months after the recall, Mazda has not fixed the…
NHTSA Recall # 23V-487 Manufacturer Recall # 6023G issued July 14, 2023 After repeated phone calls to the Manufacturer and the Mazda Dealership, the recall has not been fixed. I have been told that the parts are not available. As of this date, 16 months after the recall, Mazda has not fixed the problem. I have been told by the Manufacturer and the Mazda Dealership, that parts are not available. The manufacturer told me that they have no date when parts will be available. I have asked to speak with a Manager at the Manufacturer and was told that there is no one else to talk to except Customer Service. I asked for a contact at the Corporate level that I could send an email to, and was told that there was no email address available. They have suggested that I get it fixed at my own cost and submit a claim that may or may not be reimbursed. I consider the distorted rear view camera picture to be a safety hazard when backing up. I believe that 16 months should be plenty of time to fix this problem and that Mazda just does not want to fix a manufacturing problem on a 8 year old car.
- Back over prevention › Warnings · Electrical system · Visibility/wiper
It’s been over a year since recall number 23v-487 was issued Need to get it taken care of
- Back over prevention
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while in reverse, the digital display screen flickered before going black. The…
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while in reverse, the digital display screen flickered before going black. The display screen failed to produce a proper image after powering on independently. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 100,000. VIN tool confirms parts not available.
- Back over prevention
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while shifted into reverse, the digital display screen flickered before going…
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while shifted into reverse, the digital display screen flickered before going black and failed to display a proper rearview image. Upon further inspection, the contact noticed that when the A/C was activated, the rearview image was flickering quickly. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The manufacturer was made aware of the failure. The failure mileage was unavailable. VIN tool confirms parts not available.
- Back over prevention
The contact owns a 2016 Mazda Mazda3. The contact stated that the digital screen went blank and was repaired previously under an extended warranty. The contact then received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not…
The contact owns a 2016 Mazda Mazda3. The contact stated that the digital screen went blank and was repaired previously under an extended warranty. The contact then received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while in reverse, the digital screen displayed a distorted image. In addition, the failure was occasionally self-corrected after opening and closing the trunk of the vehicle. The local dealer was contacted, but the vehicle was not diagnosed or repaired due to the cost. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 125,000. VIN tool confirms parts not available.
- Fuel/propulsion system
Fuel Tank has corrosion that allows vapors to enter the passenger compartment.
- Unknown or other
Rear view camera intermittently cuts out. Recall was issued 07/14/23 yet there is no fix yet??? Mazda Recall #: 6023G NHTSA Recall #: 23V-487
- Unknown or other
I was notified of a recall concerning the camera in my car in september of 2023. It will soon be september 2024 and I have not been notified that the parts needed are currently available.original recallnotice stated that replacement parts were not available at that time. how can this be called an…
I was notified of a recall concerning the camera in my car in september of 2023. It will soon be september 2024 and I have not been notified that the parts needed are currently available.original recallnotice stated that replacement parts were not available at that time. how can this be called an important safety recall when a year has gone by my camera not only flickers, but most of the time it doesn't come on at all! Please advise what I should do next.
- Unknown or other
The recall related to the rear backup camera has not been addressed and it is more than a year later. I just got off the phone with a Mazda representative and they still do not have a solution nor know when one might be available. I would like to sell my car but with a defective backup camera and…
The recall related to the rear backup camera has not been addressed and it is more than a year later. I just got off the phone with a Mazda representative and they still do not have a solution nor know when one might be available. I would like to sell my car but with a defective backup camera and view screen, I will have trouble doing so and/or won't get as much for the vehicle as I should. I have a 5 year old and I don't feel safe driving this vehicle, as the rearview camera turns off suddenly at times when I am reversing the vehicle. I would like to submit a compliant for negligence on Mazda's part and urge you to do something to make them fix this defect. Thanks.
- Back over prevention › Sensing system › Camera · Electrical system
The rear parking assist camera has only worked intermittently since I purchased the car. There is really no pattern to when or why the camera chooses to work or not work, but It seems most affected by opening and closing the rear hatch: if it's working and i open the hatch, it stops working; if…
The rear parking assist camera has only worked intermittently since I purchased the car. There is really no pattern to when or why the camera chooses to work or not work, but It seems most affected by opening and closing the rear hatch: if it's working and i open the hatch, it stops working; if it's not working, opening/closing it will often cause it to work again. This is a problem because parking/backing up becomes a challenge when it's not working. This puts my safety at risk because it increases the chances of me having a fender bender when in reverse.
- Back over prevention
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable…
The contact owns a 2016 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
- 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
- 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11008577Some customers may complain about scratches on the instrument cluster lens.
- 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
- 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
- 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
- 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
- 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
- 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
- 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10254188Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254187Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
- 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10252507Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
- 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 10251368Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10243568Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10243551Service bulletin 09-031/20 issued on 09/21/20 IS no longer valid. It IS superceded by recall 6023g (2014-2018 mazda3 and 2016-2021 CX-3 - rearview image may not display properly).
- 10241637Some customers may complain about scratches on the instrument cluster lens.
- 10240496Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10240431Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
- 10240427Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
- 10238697Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
- 10238695Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
- 10238663Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
- 10237217Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 10237216If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10237215Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
Every Mazda MAZDA3 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.