2018 Mazda MAZDA3
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mazda › MAZDA3 › 2018
These records cover every 2018 Mazda MAZDA3. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2018 Mazda MAZDA3. Newest first.
Mazda North American Operations (Mazda) is recalling certain 2014-2018 Mazda3 and 2016-2021 CX-3 vehicles. The rearview camera image may not display properly by showing a flickering or distorted image.
Risk and remedy
Risk
A rearview camera that does not display properly can reduce the driver's rear view, increasing the risk of a crash or injury.
Remedy
Dealers will inspect and replace the rearview camera, as necessary. In addition, dealers will install a wiring harness fastening seal. All repairs will be performed free of charge. Interim notification letters, notifying owners of the safety risk, were mailed September 13, 2023. Final owner letters for affected models and model years in the states of CT, MA, MD, NJ, NY, PA and VA were mailed August 14, 2024. The remaining owner notification letters will be mailed at a future date, anticipated on or before May 1, 2025. Owners may contact Mazda customer service at 1-800-222-5500, Option 6. Mazda's number for this recall is 6023G.
Mazda North American Operations (Mazda) is recalling certain 2018 Mazda3, Mazda6, 2019 CX-3, 2018-2019 MX-5, CX-5, CX-9, and 2019-2020 Mazda2 vehicles. The impeller inside the low-pressure fuel pump may crack and deform, potentially causing the fuel pump to fail.
Risk and remedy
Risk
Fuel pump failure may cause an engine stall, increasing the risk of a crash.
Remedy
Dealers will replace the fuel pumps, free of charge. Owner notification letters were mailed July 18, 2022. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 5321K.
Mazda North American Operations (Mazda) is recalling certain 2016-2018 Mazda3 vehicles. A defective windshield wiper relay may cause the windshield wipers to become inoperative, reducing the driver's visibility.
Risk and remedy
Risk
Reduced visibility while driving can increase the risk of crash.
Remedy
Mazda will notify owners, and dealers will replace the front body control module with a new module which uses an improved wiper relay design, free of charge. The recall began May 7, 2019. Owners may contact Mazda customer service at 1-800-222-5500, option 4. Mazda's number for this recall is 3219D.
Mazda North American Operations (Mazda) is recalling certain 2018 Mazda3 vehicles, equipped with an incorrect exhaust valve spring. The incorrect exhaust valve spring may fail while driving, potentially causing an engine stall.
Risk and remedy
Risk
An engine stall can increase the risk of a crash.
Remedy
Mazda will notify owners, and dealers will inspect the engines and replace any incorrect exhaust valve springs, free of charge. The recall is expected to begin January 20, 2018. Owners may contact Mazda customer service at 1-800-222-5500. Mazda's number for this recall is 1717K.
Owner complaints
110 complaints6 involved a crash5 injuries1 deaths
What owners report most
Latest complaints
- Back over prevention · Equipment › Electrical › Infotainment
The contact owns a 2018 Mazda Mazda3. The contact stated that while reversing, the rearview camera displayed a distorted image, nearly resulting in a collision with a parked vehicle. Several unknown warning lights illuminated, creating a driver distraction. In addition, the infotainment screen…
The contact owns a 2018 Mazda Mazda3. The contact stated that while reversing, the rearview camera displayed a distorted image, nearly resulting in a collision with a parked vehicle. Several unknown warning lights illuminated, creating a driver distraction. In addition, the infotainment screen delaminated and experienced ghost touching with random phantom touches. The vehicle was taken to the dealer, where it was determined that the infotainment system required a new lens kit. The vehicle was not repaired. The manufacturer was notified of the failure by telephone, and a case was filed. The failure mileage was unknown.
- Engine and engine cooling · Fuel system, gasoline
The contact owns a 2018 Mazda Mazda3. The contact stated that while driving uphill at 45 MPH, the vehicle sputtered, hesitated to accelerate, and the check engine warning light illuminated. When the contact firmly depressed the accelerator pedal, the engine made a knocking noise, and the vehicle…
The contact owns a 2018 Mazda Mazda3. The contact stated that while driving uphill at 45 MPH, the vehicle sputtered, hesitated to accelerate, and the check engine warning light illuminated. When the contact firmly depressed the accelerator pedal, the engine made a knocking noise, and the vehicle stalled. Diagnostic testing at AutoZone retrieved DTC related to the knock sensor. The vehicle underwent a tune-up, and the knock sensors and ignition coils were replaced; however, the failure persisted. While driving, the vehicle hesitated and failed to exceed 40 MPH. The contact pulled over, restarted the vehicle, and drove to the residence with the hazard lights activated. The vehicle was taken to the dealer, where NHTSA Campaign Number: 23V487000 (Back Over Prevention) was completed. The contact associated the engine hesitation and stalling failures with NHTSA Campaign Numbers: 17V745000 (Engine and Engine Cooling) and 21V875000 (Fuel System, Gasoline); however, the dealer informed the contact that the VIN was excluded from both recalls. The manufacturer was notified of the failure by phone. The failure mileage was approximately 100,000.
- Unknown or other
The sunroof spontaneously shattered while I was driving. It sounded like a small explosion. I am positive that no object struck the vehicle.
- Visibility/wiper
The contact called on behalf of a customer who owns a 2018 Mazda Mazda3. The contact stated that the windshield wipers had become inoperable. The vehicle was taken to the contact's auto repair shop, Tire-Rama, where the windshield wiper switch was replaced; however, the failure persisted. Upon…
The contact called on behalf of a customer who owns a 2018 Mazda Mazda3. The contact stated that the windshield wipers had become inoperable. The vehicle was taken to the contact's auto repair shop, Tire-Rama, where the windshield wiper switch was replaced; however, the failure persisted. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 19V272000 (VISIBILITY); and referred the customer to the dealer for assistance. The vehicle was taken to the dealer, who informed the owner that the vehicle was not covered under the recall because the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was approximately 200,000.
- Visibility/wiper
While I was driving on the highway, I went to use my front wipers and there was no response when trying to active them. The rear wiper, front and rear washer fluid sprayers all worked. No warning lights or other signs of failure were present. I took the car to a local repair shop and they diagnosed…
While I was driving on the highway, I went to use my front wipers and there was no response when trying to active them. The rear wiper, front and rear washer fluid sprayers all worked. No warning lights or other signs of failure were present. I took the car to a local repair shop and they diagnosed it as a bad Body Control Module. Once the module was replaced and reprogrammed, the wipers worked as intended. Safety Recall 3219D describes the issue I had perfecly. My VIN is out of the range of this recall but if I had the same issue as this recall, there might be other bad parts out there and that range might need to be increased.
- Electrical system · Unknown or other
The center dashboard information screen developed "spider cracks" and got opaque in the corners of the screen. The screen would change functions / jump around commands without being touched while driving ( from NAV to radio, change radio stations etc) - apparently called 'Ghost Touch". Mazda has…
The center dashboard information screen developed "spider cracks" and got opaque in the corners of the screen. The screen would change functions / jump around commands without being touched while driving ( from NAV to radio, change radio stations etc) - apparently called 'Ghost Touch". Mazda has been aware of the defect for some time and issued a TSB ( and settled a class action lawsuit) but we never received any notification. The dealer offered no assistance as the car was out of warranty . We paid several hundred dollars to replace the screen as the car was becoming undriveable.
- Fuel system, gasoline
The contact owns a 2018 Mazda Mazda3. The contact stated that while the vehicle was parked, the contact became aware of a strong fuel odor around the exterior of the vehicle and inside the vehicle. The contact stated that the failure had occurred after refueling. No warning lights were illuminated.…
The contact owns a 2018 Mazda Mazda3. The contact stated that while the vehicle was parked, the contact became aware of a strong fuel odor around the exterior of the vehicle and inside the vehicle. The contact stated that the failure had occurred after refueling. No warning lights were illuminated. The dealer was made aware of the failure, and an appointment was scheduled for a diagnostic test. The dealer had to reschedule the appointment due to a scheduling issue. The vehicle was taken to an independent mechanic, where it was diagnosed with a crack in the top of the fuel pump. The contact was informed that the fuel pump needed to be replaced, and the vehicle was being repaired. The contact referenced an unknown recall with a similar failure; however, the VIN was not associated. The manufacturer was made aware of the failure and a case was filed. The contact was informed that the vehicle needed to be taken to a dealer for a diagnostic test. The repair coverage was denied because the vehicle was not repaired by a dealer. The failure mileage was 179,550.
- Electrical system · Engine · Power train
My 2018 Mazda 3 has an intermittent electrical failure on the high-speed CAN network that causes multiple safety-critical systems to fail while driving. When the fault occurs, the dash lights up with warnings for powertrain, ABS/traction, lane departure, collision-avoidance, TPMS, immobilizer, and…
My 2018 Mazda 3 has an intermittent electrical failure on the high-speed CAN network that causes multiple safety-critical systems to fail while driving. When the fault occurs, the dash lights up with warnings for powertrain, ABS/traction, lane departure, collision-avoidance, TPMS, immobilizer, and the check-engine light. The car also hesitates or “lurches” between 15–30 mph during these events. At one point in 2024, the vehicle went into limp mode on the freeway, creating a safety hazard. These failures are intermittent but repeatable. Diagnostic scans from 2023–2025 show multiple U-codes for lost communication between control modules; two later became permanent. The issue appears unrelated to any one component and affects many systems at once. The vehicle has been to every Mazda dealership in the North Texas region (Mesquite, Freeman, Hiley, Norm Reeves, Town North). All performed only basic scans; none completed a full CAN-bus or wiring-harness diagnostic. Town North kept the vehicle for six weeks (Sept–Oct 2025), replaced a coil and spark plugs, performed a camera calibration and a TCM update, but the network failures returned within 38 miles. We sought independent inspection only after dealerships repeatedly refused diagnosis whenever the warning lights were not on at the moment of arrival. In November 2025, a technician found significant internal corrosion inside the negative battery cable; touching the cable reproduced the full failure immediately. The corrosion extends deep into the wire sheathing. This appears to be an electrical defect affecting CAN communication and power/ground integrity. When the fault occurs, multiple safety systems disable at once and the vehicle behaves unpredictably. Mazda Corporate has declined further assistance, and the defect remains unresolved. I am filing this report because this is a recurring safety issue that may affect other vehicles of the same model and year.
- Unknown or other
The Infotainment system is cracking uncontrollably and will make the rear view camera unusable and a safety issue. It keeps resetting every minute. Mazda corporation wont pay for the repair that they are charging about 1,000 to fix it.
- Unknown or other
No incidents
- Engine · Power train
What component or system failed or malfunctioned, and is it available for inspection upon request? The high-pressure fuel pump failed. This component failure prevents the car from starting or staying running. The check engine code confirmed the high-pressure fuel pump failure. The failed component…
What component or system failed or malfunctioned, and is it available for inspection upon request? The high-pressure fuel pump failed. This component failure prevents the car from starting or staying running. The check engine code confirmed the high-pressure fuel pump failure. The failed component is currently at the Mazda dealership and is available for inspection upon request. How was your safety or the safety of others put at risk The car suddenly stalled while driving on the roadway, creating a dangerous situation. If this had happened on the freeway or in fast-moving traffic, it could have led to a serious accident. Losing power and control of the vehicle at higher speeds poses a major safety risk to both the driver and surrounding vehicles. I was fortunate that the failure occurred on a city street rather than on the freeway. Has the problem been reproduced or confirmed by a dealer or independent service center? Yes. The Mazda dealership inspected the vehicle and confirmed that the high-pressure fuel pump had failed, which was also verified by the check engine code. This failure caused the stalling and starting issues. Has the vehicle or component been inspected by the manufacturer, police, insurance representatives, or others? The vehicle was inspected by an authorized Mazda dealership, which diagnosed and confirmed the high-pressure fuel pump failure. It has not been inspected by police or insurance representatives. Were there any warning lamps, messages, or other symptoms of the problem prior to the failure, and when did they first appear? Before the final failure, the car was hesitant to start, and after it stalled, the check engine light appeared. There were no prior warning messages or signs before the car suddenly stalled while driving. Additional details: The car is only seven years old with approximately 52,000 miles, and it is concerning that such a critical component would fail this early.
- Unknown or other
The touch screen in my car has developed a malfunction known as “ghost touch,” where the screen glitches and registers inputs I am not making. This failure involves the infotainment system, and the component is still available for inspection upon request. My safety and the safety of others were put…
The touch screen in my car has developed a malfunction known as “ghost touch,” where the screen glitches and registers inputs I am not making. This failure involves the infotainment system, and the component is still available for inspection upon request. My safety and the safety of others were put at risk because the screen can suddenly change settings, including navigation, phone, and climate controls, while I am driving, which is distracting and dangerous. The problem has not yet been reproduced or confirmed by a dealer or independent service center, nor has the vehicle been inspected by the manufacturer, police, insurance representatives, or others. There were no warning lamps, messages, or other symptoms before the failure—it began suddenly and recently without prior indication.
- Electrical system
There is a infotainment display that sits on the center part of the dash that has touch screen capability that over time starts to fail and results in what is known as "ghost touch", where random screen settings change as though someone is using the touch screen on the infotainment screen. I had…
There is a infotainment display that sits on the center part of the dash that has touch screen capability that over time starts to fail and results in what is known as "ghost touch", where random screen settings change as though someone is using the touch screen on the infotainment screen. I had issues to where settings for screen brightness have changed causing my ability to see the controls being hindered and the radio sometimes turning up loudly and then off causing a scare distraction while driving. This screen is also used for the back up camera. There is currently a class action lawsuit for this.
- Back over prevention › Sensing system › Camera
I got into my car and the infotainment screen was cracked. It had been parked in moderate weather (no extreme heat or cold) and just randomly had multiple small cracks across the screen. This makes the back up camera difficult to see which is a safety concern.
- Unknown or other
My screen ghost taps (goes into apps without me touching it) plus there is screen damage. I got into my car one day and it looked like the screen was cracked. But it’s on the inside. I never been into the car crash or had any accidents happen to my car or the display. It affects my driving when I am using my back camera
- Visibility/wiper
Wiper stopped functioning, in the rain. Started with the wipers making 2 wipes rapidly, then not functioning. Next day, wipers partially functioned erratically before being stuck in the up position.
- Back over prevention › Sensing system › Camera
The Infotainment system is cracking uncontrollably and will make the rear view camera unusable and a safety issue. Mazda corporation wont pay for the repair that they are charging close to 2k to do.
- Unknown or other
Touchscreen has the "ghost screen" problem. It has gotten progressively worse over the last year. The Mazda dealership did a firmware update about 2 years ago and that didn't help. Now the screen thinks it's being pressed constantly in the same spot so it just beeps over and over again. If I'm not…
Touchscreen has the "ghost screen" problem. It has gotten progressively worse over the last year. The Mazda dealership did a firmware update about 2 years ago and that didn't help. Now the screen thinks it's being pressed constantly in the same spot so it just beeps over and over again. If I'm not on my radio, it will hit things like safety settings, emergency contacts, etc. so I have to leave my radio on all the time. I've researched this issue and it's well-known. A recall was issued for 2014-2016 models but not for anything after that.
- Unknown or other
Mazda infotainment system center display screen with spider cracking. Cracking makes part of display unreadable.
- Electrical system · Unknown or other
Mazda had previously issued a Special Service Plan (SSP) to remediate issues with their Mazda Connect Center Display (infotainment system), specifically "ghost touches" and "spider cracking" of the screen: [XXX] This Special Service Plan only applied to 2014-2016 models of the Mazda3. I own a…
Mazda had previously issued a Special Service Plan (SSP) to remediate issues with their Mazda Connect Center Display (infotainment system), specifically "ghost touches" and "spider cracking" of the screen: [XXX] This Special Service Plan only applied to 2014-2016 models of the Mazda3. I own a 2018 Mazda3 which has the exact same issue described in the above service plan. Searching online, I am far from the only person who is affected by this issue that continues to be present in newer models of the Mazda3. Mazda should replace my (and others) infotainment system, as it is unusable and distracting in it's current condition. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Unknown or other
The entertainment/navigation screen randomly started developing spidering cracks on the inside of the screen and has grown exponentially. It is getting close to the point where the screen is not readable and becoming useless. I have done research and have seen that many other Mazda owners have…
The entertainment/navigation screen randomly started developing spidering cracks on the inside of the screen and has grown exponentially. It is getting close to the point where the screen is not readable and becoming useless. I have done research and have seen that many other Mazda owners have experienced the same issue where their screens cracked from the inside rendering it useless but Mazda refuses to cover the cost of an issue that is not caused by any Mazda owner. Without this screen, I would need to hold my phone in order to use a navigation app to get around or attempt to find a phone holder so I can still get around successfully.
- Unknown or other
I have a letter for an important safety recall, re: the backup camera. The letter is dated September 2023, and I called today, after experiencing worsening deterioration of my camera, and I was told that there is currently no fix. So, after 1.5 years, I have no fix for my camera? This is a safety issue
- Electrical system · Unknown or other
Mazda has a warranty extension for the 2014-2016 Mazda 3 infotainment touch screen as it may malfunction and glitch. This glitch can be a distraction as the system believes that it is being touched and may cause many things to change in the car such as radio station, navigation setting, and even…
Mazda has a warranty extension for the 2014-2016 Mazda 3 infotainment touch screen as it may malfunction and glitch. This glitch can be a distraction as the system believes that it is being touched and may cause many things to change in the car such as radio station, navigation setting, and even some vehicle setting accessible from the infotainment screen, causing distractions. However, this issue is also possible on newer 2017 and 2018 models, and there is currently no program to fix the issue. While Mazda may seem like this is not a safety as the touch screen is disabled above 5 MPH, it can still cause distractions when coming to a stop and while stopped which may result in an accident. I think this needs to be resolved and Mazda needs to acknowledge that this touch issue "Ghost Touch" can affect all Mazdas with Mazda Connect 1. Taking this to the dealership to fix is expensive as they want to replace the entire system at a cost of $1000, which I could see many people not doing leading to more dangerous vehicles on the road.
- Unknown or other
The driver side if the door handle metallic wrap has begun peeling, I reached for my door handle and was cut by the wrap as it had torn away from the glued seems. It is small enough to cut my hand but barely visible to the naked eye. I had to put tape over the door handle to prevent further cuts…
The driver side if the door handle metallic wrap has begun peeling, I reached for my door handle and was cut by the wrap as it had torn away from the glued seems. It is small enough to cut my hand but barely visible to the naked eye. I had to put tape over the door handle to prevent further cuts from happening on my fingers. I took 2 photos as soon as the injuries happened and I realized what it was that was causing me to bleed from my scrape. The vehicle currently has a class action suit for the gas fuel pump and i contacted mazda to fix the pump and replace the door handle.
- Electrical system
NHTSA: #23V-487 This recall has not been resolved yet despite it being established in July 2023. States no remedy available, and this is very frustrating.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11011345CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
- 11011341CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
- 11011338CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
- 11011336CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
- 11011331CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
- 11011326CUSTOMER SERVICE PROGRAM CSP12 - DENSO LOW-PRESSURE FUEL PUMP CUSTOMER SERVICE PROGRAM WARRANTY EXTENSION: Attention ALL Mazda Dealers: This is a Warranty Extension and not a recall campaign. Repairs are not to be made unless there is a confirmed low-pressure fuel pump failure within the coverage period. As of November 18, 2024 Repair Procedures and Parts and Warranty documents are available.
- 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
- 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
- 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11008577Some customers may complain about scratches on the instrument cluster lens.
- 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
- 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
- 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
- 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
- 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11006998Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 11006987In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealers responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the Speedometer Replacement Label. Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazdas vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
- 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
- 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 11003351Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. If DTC P2B61:00 (Coolant control valve circuit range/performance) accompanies DTC P0126:00, this TSB is not applicable. Diagnose DTCs according to the instructions on MGSS online.
- 11000785The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
- 11000775There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
- 11000772Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254191Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
- 10254188Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 F (10 C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
- 10254187Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
- 10252508Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
- 10252507Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
- 10251387Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
- 10251368Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
- 10248392There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
- 10246121The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
- 10244679If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
- 10243569Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
- 10243568Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
Every Mazda MAZDA3 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.