2025 Mazda MAZDA3

Recalls

1 recall names the 2025 Mazda MAZDA3. Newest first.

• Air bags › Air bag/restraint control module › Software

  May 29, 2025NHTSA 25V357000171,412 vehicles

  Mazda North American Operations is recalling certain 2024-2025 Mazda3 and CX30 vehicles. The Sophisticated Air Bag Sensor (SAS) units may set an error code and deactivate the air bags, due to a low battery condition.

  Risk and remedy

  Risk

  Air bags that do not deploy in the event of a crash increase the risk of injury.

  Remedy

  Dealers will reprogram the SAS unit with improved software or replace the unit, free of charge. Owner notification letters were mailed July 24, 2025. Mazda's number for this recall is 7525E.

  Full recall details →

Owner complaints

What owners report most

1. Forward collision avoidance2
2. Unknown or other2
3. Air bags1
4. Vehicle speed control1
5. Wheels1
6. Suspension1
7. Seat belts1

Latest complaints

• Sep 28, 2026VA
  Unknown or other
  My car started displaying a telematic malfunction. The service paperwork also says U0198:00-03 CMU Communication error with emergency call unit. The Mazda dealerships maintenance department says this is currently unrepairable. According to them if I have an accident the car will not communicate…

  My car started displaying a telematic malfunction. The service paperwork also says U0198:00-03 CMU Communication error with emergency call unit. The Mazda dealerships maintenance department says this is currently unrepairable. According to them if I have an accident the car will not communicate that through the emergency call unit. The car was purchased new and has had no accidents. I have taken it to the dealership 4 separate times to repair this problem.

• May 31, 2026FL
  Vehicle speed control

  When turning a corner in my neighborhood, as I got around the corner (slow speed (10 mph?). The car gradually sped up on it's own without pushing the gas pedal. no cruise on and no floor mat problem. while in cruise control "on", the engine "reved up. took the vehicle to the dealer, they could not find a problem.

• May 23, 2026SCCrash1 injury
  Unknown or other

  The vehicle was involved in a rear and side impact collision and the car was totaled on 5/14/2026. The air bags did not deploy. There was a recall on the air bag system immediately after purchase 6/28/2025 and it was taken in July of 2025 to Mazda of Columbia, SC and it was “repaired.” The airbags of the truck that collided with the Mazda did deploy.

• May 5, 2026FL
  Seat belts
  I am reporting a catastrophic failure of the rear seatbelt restraint system in my 2025 Mazda 3. The rear seatbelt guide geometry is badly designed, allowing the webbing to bunch and jam during normal operation. This physical obstruction prevents the seatbelt from retracting, leading to three severe…

  I am reporting a catastrophic failure of the rear seatbelt restraint system in my 2025 Mazda 3. The rear seatbelt guide geometry is badly designed, allowing the webbing to bunch and jam during normal operation. This physical obstruction prevents the seatbelt from retracting, leading to three severe safety hazards: 1) Total failure to restrain occupants. 2) Structural damage to the vehicle's safety cell. 3) Public hazard where the obstructed door rebounded open into oncoming traffic. Restraint Failure: On multiple occasions, the rear seatbelt jammed in the guide clip while in use. Due to the lack of retraction, a 200lb adult passenger was able to fully exit the vehicle while the belt remained buckled. Most alarmingly, the vehicle's safety logic failed to trigger any occupancy warning alarms. The system remained "satisfied" because the buckle was engaged, despite providing zero tension or restraint to the occupant. Structural Damage & Public Hazard: Because the belt failed to retract, it remained loose and obstructed the rear door's closing path. The door rebounded off the slack belt into oncoming traffic, resulting in a significant structural dent to the C-pillar (door jamb) immediately adjacent to the striker. This deformation occurred in a critical area for side-impact protection. Efforts to Resolve: The vehicle was inspected by a dealer, who claimed the system was functioning normally despite being shown the jamming. I escalated this to the Mazda North American Operations Executive Office. The executive team issued a final dismissal, refusing to provide technical answers or acknowledge the documented failure points. Crucially, they denied my request for a Regional Technical Manager (RTM) to perform an engineering review of the guide geometry and refused to inspect the damage to the C-pillar. By refusing a corporate inspection, Mazda has ignored a reported life-safety defect and its resulting structural damage. This is documented on a video provided

• Aug 17, 2025TN
  Suspension · Wheels
  January 10, 2025, at low city speed, I struck a small pothole. The entire car felt like it had been in an accident—a violent jolt—followed by immediate vibration and a pull. Inspection showed one OEM 18" rim was bent. I contacted Mazda after diagnosing and was offered a slight discount on the…

  January 10, 2025, at low city speed, I struck a small pothole. The entire car felt like it had been in an accident—a violent jolt—followed by immediate vibration and a pull. Inspection showed one OEM 18" rim was bent. I contacted Mazda after diagnosing and was offered a slight discount on the replacement rim, not a warranty repair or full diagnosis. I have the bent rim in my possession. July 2025, at low speed, I barely contacted another small pothole and immediately felt the same drivability issues. A second rim was found damaged. This was only 4,500 miles after the first incident. I called the dealership manager; he said he would get back to me but never did. I later sent a letter that went unanswered. My subsequent research shows innumerable similar owner complaints for 2020–2025 Mazda 3s experiencing rim deformation from ordinary road irregularities. Why this is a safety issue (technical points): Bead-seat deformation & air loss: A bent alloy rim can distort the bead seat, causing slow leaks or sudden deflation, especially after heat cycles—creating a loss-of-control risk. Dynamic instability: A rim that’s even slightly out-of-round produces high-frequency vibration, steering pull, and reduced traction in turns or under braking; it can trigger ABS/ESC interventions and increase stopping distance. Load path & suspension stress: The 18" low-profile package leaves little sidewall cushion. On normal bumps/potholes, impact energy transfers directly to the wheel. Repeated “bottom-out” events may damage shocks/struts, alignment, and tires, compounding instability. Repeatability & foreseeability: Two events under ordinary use within a short interval indicate a systemic integrity problem, not random abuse. Requested resolution: A no-cost remedy: (1) replace all rims/tires with more durable parts and inspect/repair suspension; or (2) provide comprehensive wheel/tire protection and repair damaged rim; or (3) exchange he vehicle for a comparable model with no issue

• Jun 5, 2025GA
  Air bags

  I found out about this recall today. Mazda doesn’t have a fix to this recall yet. I am scared to drive my car in the event of a crash, due to the fact that my airbags won’t go off due to the recall. Mazda said to just “be aware until we have a fix” I cannot just “be aware” if I get into an accident and my airbags don’t go off.

• Feb 4, 2025MICrash
  Forward collision avoidance › Automatic emergency braking

  Car was turning left in front of me. I was going about 30 mph. I started to steer to the right of the car into a passing lane. The AEB stopped me and the guy behind me rear-ended me. The system did not need to react, I was not going to hit the car in front of me, but I could not steer to the right until I came to the passing lane.

• Jan 31, 2025MI
  Forward collision avoidance › Automatic emergency braking

  Second event: Again about 30 mph, a FEDEX truck was turning left in front of me, as I steered to the right to pass it, the AEB stopped me, fortunately there was no one behind me this time. The last time this happened I was rear-ended.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11011141Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: seats, steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions.
• 11011140When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
• 11011139A customer may complain of a rattle noise from the right side of the dash. The noise may be coming from the passenger side airbag.
• 11011138Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".
• 11009655This service information provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the batteries periodically according to the repair procedure.
• 11009654The SKYACTIV-DRIVE FW6A-EL AT uses Automatic Transmission Fluid (ATF) Type: FZ. Only use ATF-FZ to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
• 11009644Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11009643Customers may report no audio when using the infotainment fader function fully adjusted to the rear. If the customer's vehicle is among the trim levels referrenced above it is equipped with a 6-speaker infotainment system and does not include rear door speakers even though there are speaker grills/covers in the rear door panels. MazdaUSA and published vehicle specifications provide the correct information indicating that these trims are equipped with a "6-speaker audio system".
• 11009639Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
• 11008580Mazda Connect Services - Frequently Asked Questions (FAQ)
• 11008579Mazda Connect Services - Frequently Asked Questions (FAQ)
• 11008578When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
• 11008577Some customers may complain about scratches on the instrument cluster lens.
• 11008576Qi Wireless Charger symptom troubleshooting.
• 11008575Some customers may complain about the Active Driving Display not displaying turn by turn (TBT) travel direction or navigation information.
• 11008574Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
• 11008573Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control
• 11008572Alexa Built-In Frequently Asked Questions (FAQ)
• 11008571Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
• 11008430This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.
• 11008423The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. BSM system indicates vehicle on the opposite side. i-ACTIVSENSE indicator ring will not turn green Rear Cross Traffic Alert (RCTA) does not work Rear side radar sensor aiming may fail TPMS DTC(s) stored
• 11007029For improvement of electrical diagnosis, the SKYACTIV Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
• 11007027Before judging a steering wheel as having premature wear or a defect, first clean the steering wheel as explained in the repair information. Some vehicles may have steering wheel stains caused by chemicals such as hand lotions.
• 11007024Some customers will report that their fuel door was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-019/21 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2021 Mazda3 and 2020-2021 CX-30 are present.
• 11007022Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 11007019If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 11007018Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way.
• 11007015A New Automatic Transmission Fluid (ATF-A7) is being used for some 2023, 2024 and 2025 models. ATF-A7 is an extremely low viscosity formulation with low friction to achieve best-in-class fuel economy and driving performance. For easy identification, ATF-A7 is colored Red and ATF-FZ is colored Blue. There is NO interchangeability between ATF-A7 and ATF-FZ.
• 11007013Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 11007010Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
• 11007009Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11006995Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
• 11006981Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle.
• 11006918When the power windows are operated many times without being fully closed, small errors of the window position sensor may accumulate and cause improper operation of the jam-safe function. To reduce the risk of this occurrence, the AUTO function is disabled if the power window is operated 10 consecutive times without being fully closed (turning the ignition OFF and then ON does not reset the counting). If the power window is fully closed before the 10th time, the counting restarts and the AUTO function is not deactivated.
• 11006917Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
• 11005671Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11005551At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal useage.
• 11003398Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003397Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 11003396Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

Every Mazda MAZDA3 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.