2012 Toyota Tacoma
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › Tacoma › 2012
These records cover every 2012 Toyota Tacoma. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2012 Toyota Tacoma. Newest first.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2011-2016 Toyota Tacoma and 4Runner vehicles equipped with accessory hood scoops installed by SET or SET dealers. The adhesive attaching the hood scoop may weaken, allowing the hood scoop to detach from the vehicle.
Risk and remedy
Risk
If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.
Remedy
SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2014 FJ Cruiser and Tacoma vehicles equipped with accessory wheels and tires installed by Toyota or dealers prior to the vehicle's first sale. The affected vehicles may list incorrect spare tire size and/or cold tire inflation information on the tire placard. As such…
Risk and remedy
Risk
If the spare tire is inflated to the incorrect pressure provided on the placard, tire failure may occur while it is being driven on, increasing the risk of a crash.
Remedy
For the involved vehicles, overlay stickers to correct the tire placard will either be mailed to owners or provided to dealers for placement over the incorrect information on the placard. The recall is expected to begin in September 2014. Owners may contact Toyota customer service at 1-800-331-4331.
Toyota is recalling certain model year 2012 and 2013 Toyota Tacoma and Lexus RX350 vehicles and certain model year 2012 Toyota Rav4 vehicles. In the affected vehicles, the brake system contains a brake actuator that adjusts the fluid pressure of each wheel cylinder. An electrical component within the actuator may experience an increased resistance…
Risk and remedy
Risk
If this occurs, these systems could become inoperative, reducing the directional control assistance, increasing the risk of a crash.
Remedy
Toyota will notify owners, and Toyota and Lexus dealers will update the software for the Skid Control electronic control unit, free of charge. The recall began on March 28, 2014. Owners may contact Toyota at 1-800-331-4331.
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2012-2013 Tacoma vehicles equipped with 18" Maverick Alloy Wheels. In the affected vehicles, the spare tire requires the use of a different style of lug nut to attach it to the vehicle than the other wheels use. These lug nuts were not provided with the vehicle.
Risk and remedy
Risk
If the spare tire/wheel is installed on the vehicle using the lug nuts from another wheel, damage to the wheel could result and may eventually lead to a loose wheel, increasing the risk of a crash.
Remedy
SET will notify owners, and dealers will: (a) Install a Warning Label on the spare tire/wheel, (b) supply a bag containing proper spare wheel lug nuts, and (c) place an Owner's Manual Addendum in the vehicle's glove box. The recall began on January 23, 2014. Owners may contact SET at 1-954-429-2000.
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota…
Risk and remedy
Risk
An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy
Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013…
Risk and remedy
Risk
If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy
Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Gulf states toyota (gst) IS recalling certain model year 2012 tacoma trucks. The tire and loading information placard on each vehicle contains inaccurate spare tire size and cold inflation pressure information. thus, these vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 110,Tire selection and rims.
Risk and remedy
Risk
An incorrect placard could lead to improper spare tire use or replacement which could result in a tire failure, increasing the risk of a crash.
Remedy
Gst will notify owners, and send each owner a corrected placard, free of charge. the safety recall began on june 5, 2012. owners may contact gulf states toyota, inc. At 1-713-744-3465.
Owner complaints
295 complaints16 involved a crash6 injuries
What owners report most
Latest complaints
- Fuel/propulsion system
Vehicle: 2012 Toyota Tacoma VIN: [XXX] Toyota Special Service Campaign 20TC01 was performed on September 19, 2024, at approximately 103,417 miles. The campaign addressed the secondary air injection system, including the air injection pump and air switching valves. According to Toyota's repair…
Vehicle: 2012 Toyota Tacoma VIN: [XXX] Toyota Special Service Campaign 20TC01 was performed on September 19, 2024, at approximately 103,417 miles. The campaign addressed the secondary air injection system, including the air injection pump and air switching valves. According to Toyota's repair records, the dealer installed an air switching valve kit, air pump repair kit, and air pump cover under campaign SSC 20TC01. On XXX, at approximately 111,187 miles, the same Toyota dealership diagnosed failure of the air pump and air switching valves and estimated $3,664.13 for repair. The recurrence occurred after only about 7,770 miles and less than two years after completion of Toyota's campaign repair. I am concerned that the campaign remedy did not provide a lasting correction of the condition affecting the air injection system. Toyota has declined assistance despite the failure involving the same system that was the subject of SSC 20TC01. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Seats
- Driver’s seat back recliner mechanism / seatback locking mechanism. During a rear-end interstate collision while stopped in traffic, the driver’s seat suddenly reclined backward unexpectedly. After the accident, the recliner adjustment knob/handle was found detached at the tow yard. The vehicle…
- Driver’s seat back recliner mechanism / seatback locking mechanism. During a rear-end interstate collision while stopped in traffic, the driver’s seat suddenly reclined backward unexpectedly. After the accident, the recliner adjustment knob/handle was found detached at the tow yard. The vehicle is currently at a tow/salvage yard and may be available for inspection upon request. - Because the seat reclined unexpectedly during impact, the driver’s body position changed suddenly and the front airbag did not appear to make protective contact. The driver briefly lost consciousness and is experiencing significant neck stiffness and pain following the crash. The seat movement may have reduced the effectiveness of the airbag and seatbelt system and increased risk of head and neck injury. - No. The vehicle has not been evaluated by a dealer or independent service center at this time due to collision damage. - The vehicle has been inspected by police at the accident scene and is pending inspection by insurance. The seat mechanism has not yet been specifically evaluated by the manufacturer. - No warning lights, messages, or prior symptoms related to the seat or restraint system were observed before the accident.
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2012 Toyota Tacoma. It was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 51,350 and at the time of registration, it was discovered that the mileage was 212,400. The VIN was not available
- Air bags
The contact owns a 2012 Toyota Tacoma. The contact stated that while driving at 35-40 MPH, coming up on fog, the driver, attempting to slow down, traveled over a slush patch in the roadway, and an approaching vehicle was in view. She lost control of the vehicle, spun around, and went face-first…
The contact owns a 2012 Toyota Tacoma. The contact stated that while driving at 35-40 MPH, coming up on fog, the driver, attempting to slow down, traveled over a slush patch in the roadway, and an approaching vehicle was in view. She lost control of the vehicle, spun around, and went face-first into a ditch, and the vehicle flipped and rolled over onto the hood. There were no warning lights illuminated. The contact stated that she sustained a concussion, hematoma, and pain on the left side of her neck and head, and the next day, there was pain on the right side of her neck and shoulder. She was taken by ambulance to the hospital, where medical attention was provided. The side curtain on the driver's and passenger's sides deployed. The front airbags failed to deploy. The vehicle was towed to an independent auto center. There was no reported fire. A police report was filed. Previously, while turning around in a parking lot, the contact crashed into a cement barrier. The airbags did not deploy. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified. The failure mileage was approximately 240,000.
- Power train › Automatic transmission › Cooling unit and lines · Structure › Frame and members › Underbody shields · Tires › Pressure monitoring and regulating systems
The contact owns a 2012 Toyota Tacoma. The contact stated that the undercarriage of the vehicle was significantly rusted. The TPMS warning light was illuminated. The vehicle was taken to the local dealer, where it was repaired under the warranty; however, the failure recurred. The dealer informed…
The contact owns a 2012 Toyota Tacoma. The contact stated that the undercarriage of the vehicle was significantly rusted. The TPMS warning light was illuminated. The vehicle was taken to the local dealer, where it was repaired under the warranty; however, the failure recurred. The dealer informed the contact that the rear bumper and brackets were rusted, and there was no recall or warranty coverage. The contact stated upon pulling into the driveway of the residence, the contact noticed a trail of fluid leak on the street. The contact stated that the transmission lines were fractured due to rust. The vehicle was taken to an independent mechanic, where the contact was informed that the vehicle was significantly rusted. The vehicle was not repaired. The manufacturer was contacted and a case was filed. The failure mileage was approximately 71,000.
- Suspension
My leaf spring(s) is noisy/loosened and to the best of my limited knowledge is at risk for breaking off and puncturing the fuel tank per repair shops. This issue is not covered under Safety Recall E02 (E12) by Toyota for the model year 2012 Tacoma. As a consumer, I don't understand the…
My leaf spring(s) is noisy/loosened and to the best of my limited knowledge is at risk for breaking off and puncturing the fuel tank per repair shops. This issue is not covered under Safety Recall E02 (E12) by Toyota for the model year 2012 Tacoma. As a consumer, I don't understand the determination of when the recall is cut off for specific model years. I would like for NHTSA and Toyota to analyze this issue as the model year 2012 Tacoma could be at risk. I have case with Toyota Customer Resolutions that has been closed. Thanks for your attention into this matter.
- Steering
While driving on the road truck locks up occassionally in a curve. i know of mulitple trucks its happening to and only in curves- will end up hurting someone if a fix for it isnt found - no one seems to know what is going on
- Wheels › Rim
The contact owned a 2012 Toyota Tacoma. The contact stated that while his son was driving 40 MPH, the rear driver-side wheel rim detached. The traction control and ABS warning lights were illuminated. The vehicle veered to the right, accelerated independently, and went up the embankment, hit a…
The contact owned a 2012 Toyota Tacoma. The contact stated that while his son was driving 40 MPH, the rear driver-side wheel rim detached. The traction control and ABS warning lights were illuminated. The vehicle veered to the right, accelerated independently, and went up the embankment, hit a tree, and accelerated independently down the embankment when the vehicle flipped on the passenger side, where it came to a stop. The driver-side and passenger-side air bags deployed, and the side curtain air bags deployed. A police report was not filed. There were no injuries sustained. The vehicle was towed to an independent mechanic but was not diagnosed or repaired. The insurance company was contacted, and pending results. The manufacturer was not made aware of the failure. The failure mileage was unknown. The VIN was not available.
- Power train
My truck started having a vibration when driving around 45-55 mph. This problem first became noticeable when it had about 115,000 miles on it. Over time the speed that the vibration became noticeable at gradually increased. By 125,000 miles on the truck, it was vibrating hard between 60 and 70…
My truck started having a vibration when driving around 45-55 mph. This problem first became noticeable when it had about 115,000 miles on it. Over time the speed that the vibration became noticeable at gradually increased. By 125,000 miles on the truck, it was vibrating hard between 60 and 70 mph. The dealership determined that the problem was that the drive shaft was out of balance and that it had to be replaced. They replaced the drive shaft, but this doesn't seem like a problem that should creep up with that relatively few miles on the vehicle, and I have read that if the drive shaft actually fails, it can severely damage the vehicle and potentially cause injury.
- Structure › Body
Under the bottom of my truck, there is tons of rust. I know a lot of the trucks my year, make, and model has been recalled for rust on the body and other parts of the truck. I was told that a Toyota dealership should replace it with the amount it has, and now a hole has appeared but they only told me a price to fix everything that is rusted. Just puts my vehicle at risk driving it back and forth to work.
- Service brakes · Structure › Body · Unknown or other
Will not fix the frame. my husband has a 2005 and it looks new compared to my 2012. The last mechanic I used told me not to bring it back to him to much rust. Toyota said it passed their inspection. There is no way. They’ve had my truck almost a yr. I thought they was fixing it. No they just been…
Will not fix the frame. my husband has a 2005 and it looks new compared to my 2012. The last mechanic I used told me not to bring it back to him to much rust. Toyota said it passed their inspection. There is no way. They’ve had my truck almost a yr. I thought they was fixing it. No they just been chilling. They never called me to tell me it was they wouldn’t honor the recall. Nothing. I keep reading on here cold climate states are the only complaints. Someone is lying on here because I know at least 20 Toyota Tacoma owners from Texas who have filed incident reports.
- Fuel/propulsion system
The check engine light on the dashboard of my 2012 Tacoma turned on and will no longer accelerate appropriately and especially while driving uphill, posing a danger to myself and other drivers. I was on a two-lane highway with a cliffside drop on one side and a wall of steep rock on the other and…
The check engine light on the dashboard of my 2012 Tacoma turned on and will no longer accelerate appropriately and especially while driving uphill, posing a danger to myself and other drivers. I was on a two-lane highway with a cliffside drop on one side and a wall of steep rock on the other and absolutely no where to go as there was only one lane going in each direction and my truck would not accelerate over 20mph in an area where you’re expected to keep a pace above 40mph and as such ended up with a long row of impatient and increasingly frustrated drivers behind me, only more incited by my having to turn on my hazard lights as a result of a crawling speed I was forced to deal with and with nowhere to pull over and get out of the way. How can I possibly rely on this vehicle to be safe for me or anyone else, especially on a fast-moving highway in this condition? I have taken the vehicle to an auto shop and I as told the air injection system is bad and that this is a typical problem for Toyota Tacomas and the cost would be just shy of $3,000! I was recommended by a mechanic to reach out to Toyota directly because this is obviously an issue the manufacturer should readily respond to and repair. Please advise.
- Steering
Sudden and total loss of power steering while backing up to park. There were/are no warning lights or messages displayed on the dashboard. With great difficulty, I was able to drive the car to my local mechanic. Steering was extremely difficult. The power steering unit has been ordered by my mechanic.
- Fuel/propulsion system · Service brakes · Unknown or other
My truck lost drivability while I was going 60 I ran into a ditch to stop. It hads two codes . I took it in they replaced my rack n pinion. Check engine light came on . Mechanic said he could not work on it anymore because of the rust. To much corrosion he would be risking liability for other…
My truck lost drivability while I was going 60 I ran into a ditch to stop. It hads two codes . I took it in they replaced my rack n pinion. Check engine light came on . Mechanic said he could not work on it anymore because of the rust. To much corrosion he would be risking liability for other parts getting damaged because of all the rust. Took it to mike Shaw to have frame tested. It passed they said. But I can’t find a mechanic to work on it but mike Shaw and they’ll just keep charging for each item they don’t care.
- Power train
Drivetrain vibration and cricket chripping noise; likly coming from propeller shaft
- Engine and engine cooling
The contact owns a 2012 Toyota Tacoma. The contact stated that while driving, the vehicle failed to exceed 45 MPH. The contact stated that the check engine and traction control warning lights were illuminated. The vehicle was taken to an independent mechanic who informed him about a Special Service…
The contact owns a 2012 Toyota Tacoma. The contact stated that while driving, the vehicle failed to exceed 45 MPH. The contact stated that the check engine and traction control warning lights were illuminated. The vehicle was taken to an independent mechanic who informed him about a Special Service Campaign: 20TC01. The vehicle was taken to the local dealer where it was diagnosed and determined that the air injection pump needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and informed him that the Special Service Campaign: 20TC01 had expired. No additional assistance was provided. The failure mileage was approximately 85,000.
- Unknown or other
The frame has rusted through in several spots.
- Suspension
The passenger leaf spring or right leaf spring has broken and the truck has not hauled any kind of weight, there is a previous recall on similar trucks but they end with 2011 models but looking at the 2012 model it’s build is similar and seems to have a chance of having the same effect as mine already has.
- Electronic stability control (esc) · Service brakes, hydraulic
The contact owns a 2012 Toyota Tacoma. The contact stated that while driving at various speeds in areas with low traction, several unknown warning lights would illuminate on the instrument panel and the vehicle would begin to drift independently. Once the contact regained control of the vehicle…
The contact owns a 2012 Toyota Tacoma. The contact stated that while driving at various speeds in areas with low traction, several unknown warning lights would illuminate on the instrument panel and the vehicle would begin to drift independently. Once the contact regained control of the vehicle, the warning lights would disappear, and the vehicle would resume normal operation. The contact had taken the vehicle to a dealer for repair. Upon investigation, the contact discovered NHTSA Campaign Number: 14V054000 (Service Brakes, Hydraulic, Electronic Stability Control) which he linked to the failure. Upon speaking with the dealer, the contact was informed that the vehicle was not included in the recall. The manufacturer was also notified of the failure and the contact was directed to the website for assistance. The vehicle remained in the possession of the dealer and had yet to be repaired. The failure mileage was approximately 85,500.
- Unknown or other
I was attempting to park in a parking space to return items at a department store at a mall. All of a sudden my truck accelerator on its own. The truck traveled over two cements curbs crossed a road before traveling through a chain-link fence down the front of retaining wall into a wooded area…
I was attempting to park in a parking space to return items at a department store at a mall. All of a sudden my truck accelerator on its own. The truck traveled over two cements curbs crossed a road before traveling through a chain-link fence down the front of retaining wall into a wooded area swamp. It took three tow trucks to remove the truck. Police report 21-374-AC. Truck wasn't repairable so my insurance company totalled the truck. I filed a complaint with Toyota in Case number 210602000065 but no outcome. This is the second time this truck has had accelerator issues. My first complaint was Aug 2019 with Toyota case number 1908060035. Toyota pulled the black box and came back stating they couldn't find anything.
- Suspension
Is there a recall on leaf springs
- Fuel/propulsion system
Switching valve stuck open bank 1 and 2. Truck is in limp mode. Air pump is full of water.
- Engine · Service brakes · Vehicle speed control
June 1st 2021 I went to park in a parking space at a local mall. My truck instead of stopping it accelerated out of control jumped two stone curbs, drove though a fence and landed into a swamp. Call Toyota and they have opened a new case # 210602000065. Police report # 21-374-AC. This isn't the…
June 1st 2021 I went to park in a parking space at a local mall. My truck instead of stopping it accelerated out of control jumped two stone curbs, drove though a fence and landed into a swamp. Call Toyota and they have opened a new case # 210602000065. Police report # 21-374-AC. This isn't the first time that this has happen with this truck. It happen in Aug 2019. I contacted Toyota case number 1908060035. They sent out EAA Engineering Analysis Ass. out who did a ACM.CDRX file a month later. Toyota came back said they couldn't find anything wrong and my case was closed. Another incident in winter of 2016 where my truck was stopped and it accelerated on its own and It drove in the 4 way intersection where it caused an accident. lots of damage to cars. Toyota was contacted and they sent me to a dealer for repairs. Dealership has records of my truck coming in since I owned it with complaints of Truck not moving at all to all of sudden to acceleration on its own.
- Service brakes · Traction control system
TL* the contact owns a 2012 toyota tacoma. The contact stated while driving 80 mph, while the brake pedal was not being depressed, the brakes locked up which caused the vehicle to start sliding. The contact stated that the traction control warning light was illuminated. The vehicle was not taken to…
TL* the contact owns a 2012 toyota tacoma. The contact stated while driving 80 mph, while the brake pedal was not being depressed, the brakes locked up which caused the vehicle to start sliding. The contact stated that the traction control warning light was illuminated. The vehicle was not taken to a dealer. The vehicle was not repaired. Upon investigation, the contact associated the failure with nhtsa campaign number: 14v054000 (service brakes, hydraulic, electronic stability control) however, the vin was not included. The manufacturer was not informed of the failure. The failure mileage was approximately 76,000.
- Suspension
Having the same issue as the 2011 tacoma's with faulty leaf springs started as a squeak sprayed WD-40 and fluid film didn't help then few months later heard a clunk and now driver side leaf spring IS broke this should be covered under the recall!!
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Electrical overstress
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air…
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005119This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005115Toyota plans to conduct Safety Recall and Service Campaign follow-up notifications to owners whose vehicles have not yet had the following Safety Recall and/or Service Campaign repairs completed
- 11005114Safety Recall and Service Campaign completion is an important part of our commitment to customer satisfaction of Toyota products. Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005061This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005057Toyota plans to conduct Safety Recall and Service Campaign follow-up notifications to owners whose vehicles have not yet had the following Safety Recall and/or Service Campaign repairs completed
- 11005056Safety Recall and Service Campaign completion is an important part of our commitment to customer satisfaction of Toyota products. Toyota will be conducting follow-up notifications to remind owners whose vehicles have not yet had Safety Recall and/or Service Campaign repairs completed in the campaigns listed
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251757Ti: K0D expired on 10/31/2023. Technical instructions for limited service campaign K0D frame corrosion resistant compound (crc) application certain 2016 ? 2017 model year tacoma
- 10251756K0D expired on 10/31/2023.
- 10251755DP: K0D expired on 10/31/2023. Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
- 10251742Ti: K0D expired on 10/31/2023. Technical instructions for limited service campaign K0D frame corrosion resistant compound (crc) application certain 2011 ? 2015 model year tacoma
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
- 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10244108TSB: Some 2005 ? 2023 model year Tacoma vehicles equipped with a manual transmission may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released.
- 10244107RL: safety recall & service campaign renotification owner renotification 23r002
- 10244106Dl: safety recall & service campaign renotification owner renotification 23r002
- 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
- 10238142DL: Toyota has received a number of reports regarding vehicle frame corrosion perforation on certain 2011-2017 model year Tacoma vehicles. These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame. Although perforation of the vehicle?s frame is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to vehicle frame corrosion perforation. A separate program (limited Service Campaign K0D) will include CRC (Corrosion Resistant Compound) application. CRC application will be covered under Limited Service Campaign (LSC K0D) for a period of two years and will only be available for vehicles registered/regularly operated in the Cold Climate States that do not meet vehicle frame replacement criteria.
- 10238141DP: Toyota has received a number of reports regarding vehicle frame corrosion perforation on certain 2011-2017 model year Tacoma vehicles. These reports have indicated that these vehicles, when operated in specific cold climate areas (Cold Climate States1) with high road salt usage, or exposed to other environmental factors, may exhibit more-than-normal corrosion to the vehicle?s frame. Although perforation of the vehicle?s frame is covered by Toyota?s New Vehicle Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Toyota care about the customers? ownership experience. Toyota is providing coverage for repairs related to vehicle frame corrosion perforation. A separate program (limited Service Campaign K0D) will include CRC (Corrosion Resistant Compound) application. CRC application will be covered under Limited Service Campaign (LSC K0D) for a period of two years and will only be available for vehicles registered/regularly operated in the Cold Climate States that do not meet vehicle frame replacement criteria.
- 10227898TSB: Some 2005 ? 2022 model year Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty smell is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this service bulletin is to provide general guidelines and procedures for odor remediation. This service bulletin provides a guide on how to prepare the interior of the vehicle prior to an odor remediation being performed, as well as contact information for an approved vendor who will arrange the remediation, and instructions on how to prepare the interior of the vehicle for reassembly once the remediation has been completed. Refer to all model and model year specific Repair Manuals and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This service bulletin is to provide a general overview and direction for the odor remediation process.
- 10224147DP: Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
- 10224130DP: Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment
Every Toyota Tacoma model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.