2023 Toyota Tacoma
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › Tacoma › 2023
These records cover every 2023 Toyota Tacoma. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2023 Toyota Tacoma. Newest first.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2023 Toyota Corolla, Corolla Cross, Corolla Cross Hybrid, Highlander, Highlander Hybrid, Tacoma, Lexus RX350, 2023-2024 NX250, and NX350 vehicles that may have been incorrectly repaired under previous NHTSA recall number 23V-480. An electrical connection inside the steering column's…
Risk and remedy
Risk
A deactivated driver's air bag will not deploy as intended, increasing the risk of injury during a crash.
Remedy
Dealers will inspect and replace the spiral cable assembly as necessary, free of charge. Owner notification letters were mailed March 17, 2025. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's number for this recall is 25TA02. Lexus' number for this recall is 25LA02.
Toyota Motor Engineering & Manufacturer (Toyota) is recalling certain 2022-2023 Tacoma vehicles. The axle shaft sub-assembly may separate from the axle housing due to debris causing improperly secured fasteners.
Risk and remedy
Risk
Axle shaft separation can cause a loss of vehicle stability and brake performance, increasing the risk of a crash.
Remedy
Dealers will inspect the rear axle assembly, tighten the axle retaining nuts as necessary, and repair or replace any damaged components, free of charge. Owner notification letters were mailed April 17, 2024. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are 24TB05 and 24TA05.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2023 Corolla, Corolla Cross, Corolla Cross Hybrid, Highlander, Highlander Hybrid, Tacoma, 2023 Lexus RX350, RX350 Hybrid, RX500 Hybrid, 2023-2024 Lexus NX250, NX350, and NX350 Hybrid vehicles. An electrical connection inside the steering column's spiral cable assembly may be…
Risk and remedy
Risk
A deactivated driver's air bag that does not deploy as intended increases the risk of injury during a crash.
Remedy
Dealers will inspect and replace the spiral cable assembly, if necessary, free of charge. Owner notification letters were mailed September 8, 2023. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's number for this recall is 23TA08. Lexus' number for this recall is 23LA02.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2023 Tacoma vehicles. One or more of the individual welds in the upper child seat anchors may be insufficient. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 225, "Child Restraint Anchorage System."
Risk and remedy
Risk
An insufficient weld may prevent the child seat from being anchored properly, allowing the seat to move during a sudden stop or crash, increasing the risk of injury.
Remedy
Dealers will inspect the upper child seat anchors and reweld the child seat anchors, as necessary. Owner notification letters are expected to be mailed September 02, 2022. Owners may contact Toyota's customer service at 1-800-331-4331. Toyota's number for this recall is 22TB09/ 22TA09.
Owner complaints
54 complaints5 involved a crash1 involved a fire5 injuries
What owners report most
Latest complaints
- Electrical system · Lane departure › Blind spot detection
Check BSM light came on Dealer found chafed wiring harness
- Vehicle speed control
After initial start of engine and at idle there is surge of the engine and lunge forward while in drive. The danger is unexpected forward movement of the truck when pulling forward at idle by lunging forward with risk of hitting that which is directly in front such as a parked car or the front of my garage. This is an ongoing event.
- Unknown or other
On XXX I was driving on [XXX] at about 70mph, when the rear drivers side window on a 2023 Toyota tacoma crew cab shattered suddenly. If someone had been sitting in the backseat when this occurred they could have been injured. The door panel itself was damaged from the tiny shards of glass. It…
On XXX I was driving on [XXX] at about 70mph, when the rear drivers side window on a 2023 Toyota tacoma crew cab shattered suddenly. If someone had been sitting in the backseat when this occurred they could have been injured. The door panel itself was damaged from the tiny shards of glass. It was a dangerous situation as glass was most likely showering the vehicles behind me as this occurred. This vehicle only had 22,200 miles on it at the time and was a stock vehicle. No modifications were added. I had all the windows closed and the AC and recirculating air was on at 2 bars. It was about 8:30 at night when this happened. When I was able to get off the freeway and look at what happened, the glass was totally gone from the window. There was lots of glass on the door panel & well below that, a little behind the drivers seat on the floor close to the window and a little behind where the seat leaves a gap (when the seat is folded down), close to the window that blew out. There was no glass further into the vehicle, which if something had hit the window from outside, I would think the glass would have been further inside. I found more small glass pieces in the bed of my truck (6’ bed). This was a very scary situation and I didn’t do anything to cause it. A more high strung person might have reacted badly to this sudden boom and caused an accident at high speed on the highway. I have heard that similar things have happened to other drivers of certain models of toyota from 2020 - 2026. The vehicle is still under warranty and I took it to Toyota but they refused to repair it under the warranty. I am taking it to a repair shop tomorrow to get an estimate for my insurance. There was no warning prior to this occurring. It was a shock. A child in a rear seat in this situation could have sustained injury. The door panel had slices in it and the fabric is torn. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Power train · Vehicle speed control
The contact owns a 2023 Toyota Tacoma. The contact stated that the transmission failed to operate properly while driving 35 MPH and attempting to accelerate. While driving uphill or downhill, the transmission was slow to shift into the intended gear, and the vehicle was slow to accelerate.…
The contact owns a 2023 Toyota Tacoma. The contact stated that the transmission failed to operate properly while driving 35 MPH and attempting to accelerate. While driving uphill or downhill, the transmission was slow to shift into the intended gear, and the vehicle was slow to accelerate. Additionally, there was an abnormal sound while turning the steering wheel. While driving in the left lane with another vehicle in the right lane, the vehicle stopped suddenly. There were no warning lights illuminated. The local dealer was contacted, and the failure was associated with the gear shaft. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 15,000.
- Electrical system · Service brakes, hydraulic · Steering
The contact owns a 2023 Toyota Tacoma. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 24V152000 (POWER TRAIN). The contact stated that while driving 55 MPH, the steering wheel was firm, the brake pedal was firm, and the vehicle was violently vibrating. Several unknown…
The contact owns a 2023 Toyota Tacoma. The contact stated that the vehicle was repaired under NHTSA Campaign Number: 24V152000 (POWER TRAIN). The contact stated that while driving 55 MPH, the steering wheel was firm, the brake pedal was firm, and the vehicle was violently vibrating. Several unknown warning lights were illuminated. The message “Pull Over – Do Not Drive” was displayed before the vehicle lost automotive power. The vehicle was pulled over to the side of the road and was towed back to the dealer. The vehicle was inspected; however, the vehicle was not diagnosed or repaired. The contact was informed that the battery and alternator needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 43,000.
- Exterior lighting
Headlight tabs break causing housing to rub against body and crack. Additionally it makes headlights move which necessitates constant readjustment.
- Air bags
Only the side window airbags deployed during a collision. There was no protection from the front impact. Insurance representatives have the vehicle and we are waiting to hear about the outcome. While in the car pool lane traveling approximately 65mph, a Honda civic left the lane to the right of us…
Only the side window airbags deployed during a collision. There was no protection from the front impact. Insurance representatives have the vehicle and we are waiting to hear about the outcome. While in the car pool lane traveling approximately 65mph, a Honda civic left the lane to the right of us and veered directly into our lane. I applied the brakes as hard as I could, but did not swerve due to fear of rolling into the opposite direction of traffic. His back driver side came into my front passenger side at the immediate collision and then we flipped onto the driver side and slid for quite a few feet. Only the airbags on the doors/windows deployed. There was very little reaction time to apply the brakes due to the speed and closeness of the Honda coming into our lane. The airbags in the front console would have protected us from the whiplash we received.
- Steering
While checking wiper fluid levels for 2023 Toyota Tacoma TRD Off Road, noticed power steering fluid was below minimum line. No leaks were noticed on the ground where the vehicle is normally parked, underneath the reservoir or along the hoses related to the power steering system. Upon inspecting the…
While checking wiper fluid levels for 2023 Toyota Tacoma TRD Off Road, noticed power steering fluid was below minimum line. No leaks were noticed on the ground where the vehicle is normally parked, underneath the reservoir or along the hoses related to the power steering system. Upon inspecting the tie rod boots, it was noticed that they appeared to be holding fluid, due to signs of moisture on the exterior of the boots. Vehicle was taken to the dealership where purchased. Vehicle was purchased November 2022 and now has approximately 52,000 miles). The dealership service department determined the steering rack seals failed and power steering fluid was dripping into the tie rod boots. Vehicle was out of the 3 year / 36,000 mile warranty and this known issue is not covered by the power train warranty, so 100% of the cost to repair falls upon the owner. Dealer stated that this is a known issue but could not state why a recall was never initiated to alleviate the issue and prevent this costly repair from falling upon the vehicle owners. If not repaired the issue could cause sudden, dramatic increases in steering effort and total loss of vehicle control. Low fluid can also damage internal pump components if not caught early enough.
- Air bags · Unknown or other
Air Bags (Driver and Passenger Curtain Airbags) no other airbags deployed. Been in repair since 3/8/26. Currently 4/21/26. Insurance already sent Body Shop money. Parts on National Backorder and Manufacturer Switch has not been determined yet by Toyota. Truck will not be released back to me until…
Air Bags (Driver and Passenger Curtain Airbags) no other airbags deployed. Been in repair since 3/8/26. Currently 4/21/26. Insurance already sent Body Shop money. Parts on National Backorder and Manufacturer Switch has not been determined yet by Toyota. Truck will not be released back to me until the repair is completed per email. I need adequate transportation provided to continue going to and from work. My insurance has maxed its coverage and cannot extend. I should not be out of pocket more than I already am while waiting on a part that is not in my control. Accident: I hydroplaned and ended in a ditch after going over a T-Intersection. Air bags went off and vehicle was drivable after. Submitted a claim to insurance and here we are.
- Air bags
I got into a head-on collision with a cement center median going roughly 45-50MPH after fishtailing on black ice. My airbags did not deploy at that speed, I contact toyota corporate and they only removed the CDR information and did not assess the airbag sensors themselves. I was able to press the…
I got into a head-on collision with a cement center median going roughly 45-50MPH after fishtailing on black ice. My airbags did not deploy at that speed, I contact toyota corporate and they only removed the CDR information and did not assess the airbag sensors themselves. I was able to press the SOS button for EMS to arrive. My safety was put at risk as none of my airbags deployed. It was not inspected by my insurance company and was taken to an automotive shop to be repaired. No prior warning systems were enacted,
- Electrical system · Fuel/propulsion system
On February 16 I started my vehicle to drive home from work and the vehicle threw multiple error codes and shutdown while driving and would not start again. It was towed to the dealership. The dealership advised the problem was remedied. 11 days later the same problem occurred, vehicle threw multiple error codes and shutdown while driving. Vehicle needed to be towed again to the dealership.
- Engine
Oil cap went loosed and fell off after a few hundred miles of driving. This is a very common thing in 2023 Toyota tacoma.
- Engine
Deep knocking noise they call the taco tick is actually the a problem with the motor. There is an issue valve train and timing chain, tensioners and pulleys. Toyota USA decide to tell all consumers it’s just the way they sound. So they do not have to repair millions of these trucks on recall they refuse to repair under manufacture warranty or power train warranty they wait until it becomes the consumers problem
- Electrical system · Service brakes · Steering
On June 20, 2025, my 2023 Toyota Tacoma (VIN [XXX] ed a sudden loss of effective braking during normal driving conditions (dry roadway, clear weather). The vehicle was being driven by my adult son. While slowing for a turn, the instrument cluster displayed a Pre-Collision System (PCS) malfunction…
On June 20, 2025, my 2023 Toyota Tacoma (VIN [XXX] ed a sudden loss of effective braking during normal driving conditions (dry roadway, clear weather). The vehicle was being driven by my adult son. While slowing for a turn, the instrument cluster displayed a Pre-Collision System (PCS) malfunction warning and a Vehicle Stability Control (VSC) warning. The Driver applied the brake pedal continuously, but the vehicle did no decelerate as expected. ABS did not activate, and braking effectiveness was insufficient. During braking, the driver experienced reduced steering responsiveness. In order to avoid entering a busy roadway without adequate braking capability, the driver applied maximum steering input, fully loading the left side of the steering wheel with as much force as possible in an attempt to redirect the vehicle. Any reduction in speed occurred primarily due to the change in direction and tire to road friction, not effective braking. The vehicle was towed to a Toyota dealership. Dealer intake records document a PCS warning and no brakes upon arrival. Event Data Recorder (EDR/CDR) data shows continuous brake pedal application for approximately 5 seconds prior to the event, accelerator at 0%, and brake system hydraulic pressure reaching approximately 12.14 MPa (maximum recorded). Despite this, the vehicle did not stop as expected. No frontal crash pulse recorded. Toyota Motor North America later denied responsibility, asserting incorrect vehicle speed and stating that a CARFAX report indicated prior front-end damage. The CARFAX vehicle history report, dealer purchase disclosures, and service records show no reported accidents or damage. Toyota declined to provide brake system ECU logs (ABS/VSC/brake control modules). This incident raises concerns regarding a potential safety defect involving electronically controlled braking and its interaction with PCS stability control systems. Supporting documentation available. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5
- Power train
The contact owns a 2023 Toyota Tacoma. The vehicle was taken to the local dealer for the recall repair of NHTSA Campaign Number: 24V152000 (Power Train). The contact became aware of a weld splatter and that the nuts were rusted. The dealer marked the vehicle repaired; however, the contact stated…
The contact owns a 2023 Toyota Tacoma. The vehicle was taken to the local dealer for the recall repair of NHTSA Campaign Number: 24V152000 (Power Train). The contact became aware of a weld splatter and that the nuts were rusted. The dealer marked the vehicle repaired; however, the contact stated that the repair was not completed. The vehicle was taken back to the local dealer, where the nuts and bolts were replaced. The contact stated that the torque spec was incorrect. The dealer provided a video of the work order for the repair. The dealer informed the contact that rust could develop on the nuts. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 21,303.
- Air bags
On November 14, 2025, at approximately 0200 hours, in Fresno, California, I was driving southbound on Highway 99 at approximately 70 mph using cruise control. It was raining heavily at the time, and visibility was significantly reduced. I was traveling in the middle lane when I suddenly felt what I…
On November 14, 2025, at approximately 0200 hours, in Fresno, California, I was driving southbound on Highway 99 at approximately 70 mph using cruise control. It was raining heavily at the time, and visibility was significantly reduced. I was traveling in the middle lane when I suddenly felt what I believed to be an impact on the driver side of my vehicle. Due to the weather conditions, I was unable to visually identify what struck the vehicle. Immediately prior to this event, I noticed faint headlights in lane 1 (fast lane), but I could not determine whether that vehicle made contact with mine. At the moment of the perceived impact, the side curtain airbags deployed unexpectedly. I initially thought the deployment was a collision with another vehicle because the force felt like a physical impact. Once the curtain airbags deployed, I immediately lost control of the vehicle. Steering became impossible, and the vehicle veered off the roadway, ultimately coming to a stop on an embankment adjacent to the highway. California Highway Patrol officers responded to the scene, took my statement, and inspected the vehicle. They reported no exterior body damage consistent with a collision. The following day, I visited the tow yard and conducted a daylight inspection of the vehicle, confirming that there was no visible impact damage on the body panels or exterior surfaces. After the on-scene investigation, the vehicle was towed, and the responding officer provided me with a courtesy ride. As a result of the incident, I sustained minor injuries, including whiplash, road rash on my left shoulder and upper forearm, and soreness in my neck. This event involved unexpected deployment of side curtain airbags without any confirmed collision, leading to loss of vehicle control, roadway departure, and driver injury. I am submitting this complaint for investigation into potential airbag or sensor malfunction.
- Unknown or other
61/2 INCH SCREEN WENT BLANK on start up. Did not reappear until I got home and stopped and restarted car engine. Have on occasions there is no tire pressure showing when i checked that screen.
- Electrical system · Power train · Steering
The contact owns a 2023 Toyota Tacoma. The contact stated that while the vehicle was being serviced, the contact was informed that the rack and pinion needed to be replaced due to an oil leak. The vehicle was repaired. The contact stated that on a separate occasion, while driving at an undisclosed…
The contact owns a 2023 Toyota Tacoma. The contact stated that while the vehicle was being serviced, the contact was informed that the rack and pinion needed to be replaced due to an oil leak. The vehicle was repaired. The contact stated that on a separate occasion, while driving at an undisclosed speed, the speedometer gauge failed to function as intended. The vehicle was taken back to the dealer, and the contact was informed that the instrument panel had a factory defect. The vehicle was repaired. In addition, the contact was informed that the rear axle needed to be replaced. The vehicle was repaired. The contact stated that the rack and pinion recently failed. The contact stated that the vehicle veered to the right and the left independently while driving with an abnormal sound coming from the vehicle. The vehicle was not diagnosed or repaired after the most recent failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 30,000.
- Visibility/wiper
Passenger side windshield washer nozzle sprays the lower part of the hood. Only a little of the stream reaches the windshield. Outcome is that dust, grime, debris typically smear on passenger side of the windshield. This causes reduced visibility. Truck is a Toyota Certified Pre-Owned (TPO)…
Passenger side windshield washer nozzle sprays the lower part of the hood. Only a little of the stream reaches the windshield. Outcome is that dust, grime, debris typically smear on passenger side of the windshield. This causes reduced visibility. Truck is a Toyota Certified Pre-Owned (TPO) delivered 18Mar24 at 13K miles. Washer nozzle problem has been existent since delivery. Repair request was made at first oil change. Unlike many other brands & makes, the nozzle can't be re-aimed by simple bending. Problem could be solved by using a nozzle with a lower "aim," or some sort of adjustment. Nozzle part is difficult for car owner to remove and replace.
- Electrical system › Instrument panel › Fuel gauge
The contact owns a 2023 Toyota Tacoma. The contact stated that upon refueling, the fuel gauge indicated that there was 1/8 tank full, even though the fuel tank was full. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed, and the contact…
The contact owns a 2023 Toyota Tacoma. The contact stated that upon refueling, the fuel gauge indicated that there was 1/8 tank full, even though the fuel tank was full. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed, and the contact was informed that the VIN was not under recall. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 4,700.
- Engine
Engine began making abnormal ticking noise, heard primarily on the passenger side of vehicle. Upon removal of valve cover for inspection, found that there are chunks of camshafts breaking off causing the noise. Appears to be a manufacturing defect. Local dealer said they have seen this issue…
Engine began making abnormal ticking noise, heard primarily on the passenger side of vehicle. Upon removal of valve cover for inspection, found that there are chunks of camshafts breaking off causing the noise. Appears to be a manufacturing defect. Local dealer said they have seen this issue before. This issue could result in catastrophic engine failure and/or loss of power and cause a crash. My truck has 70k miles on it, regularly maintained and operated.
- Engine
This vehicle thermostat and sensor system are faulty! My sensor started lighting up within a year and half after purchasing. Engine was not overheating at first, they said it will eventually happen and it did; all dealers said to replace but I was out of 360000 miles due to commute to Seattle. This…
This vehicle thermostat and sensor system are faulty! My sensor started lighting up within a year and half after purchasing. Engine was not overheating at first, they said it will eventually happen and it did; all dealers said to replace but I was out of 360000 miles due to commute to Seattle. This vehicle is less then 3 years old and should have this item listed specifically in power train warranty since connected to engine directly. If engine overheats it is no longer usable and truck is useless! Engine warranty if this is a know issue from Toyota dealerships. Contacted 3-4 dealerships in the state of WA and all had known of issue. One dealer stated anything from 2020 to current has had thermostat issues. This is serious concern knowing the engine can seize up! Their thermostat and sensor should not be a combined item in my opinion. Please advise and or confirm this is an issue that should be looked into. If the engine overheats then the vehicle could cause an accident! This is a huge safety risk that can be avoided! I work and make it from paycheck to paycheck this was very expensive to fix and had to paid out of pocket. Please help others be aware of situation!
- Electrical system
The owner and operator of the vehicle, stated that they were driving the vehicle on the Interstate when they noticed white smoke and ashes emanating from the steering column. They pulled into the parking lot to investigate and opened the hood to see no smoke or fire. When they returned to the…
The owner and operator of the vehicle, stated that they were driving the vehicle on the Interstate when they noticed white smoke and ashes emanating from the steering column. They pulled into the parking lot to investigate and opened the hood to see no smoke or fire. When they returned to the passenger compartment, the smoke turned black in color, and they observed fire emanating from the steering column. I am the Lead Fire Investigator on this incident for the Edmond Fire Department. The electrical components in the area observed with fire contained electrical arc sites and melting. No other accidental heat sources were present, and natural causes and human involvement were ruled out as well. Incident number is [XXX] in Edmond, OK. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Latches/locks/linkages › Doors › Latch
Driver's door unlatched during the winter (January 2025) while stopping at an intersection. The incident repeated yesterday April 19, 2025, while driving on the freeway and turning right. The door partially opened and a warning light appeared on the dashboard. Reduced speed / stopped, to be able to…
Driver's door unlatched during the winter (January 2025) while stopping at an intersection. The incident repeated yesterday April 19, 2025, while driving on the freeway and turning right. The door partially opened and a warning light appeared on the dashboard. Reduced speed / stopped, to be able to completely open the door and close again. The vehicle has approximately 25,200 miles. Vehicle is being taken to a Toyota dealer to have the door latch inspected and to try to reproduce the failure mode. No explanation needed on why a door unlatching on its own, while cruising on a freeway, is a safety risk to the driver and others.
- Unknown or other
Exploded sunroof with no apparent debris hitting it. No vehicles around and clear sky’s. Dealer said that something most have hit it and suggested I use comprehensive part of insurance. The assembly and slide was damaged while trying to clear glass. First estimate is $4,165. Reports that even…
Exploded sunroof with no apparent debris hitting it. No vehicles around and clear sky’s. Dealer said that something most have hit it and suggested I use comprehensive part of insurance. The assembly and slide was damaged while trying to clear glass. First estimate is $4,165. Reports that even though windshield was not damaged, this also needs replaced and recalibrated. Sounds strange to replace a windshield when there is no damage to it. Upwards break suggest explosion and not hit with debris.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010059Some customers have expressed concern that the wireless functions of their Key Fob stop working. Key Fob LEDs will not turn ON, but engine starts with key held up against start button. Key battery voltage is confirmed OK and no DTC/RoB is found. This condition may occur if customer places Key Fob near wireless charger while phone is charging. When the key battery is removed and reinstalled, the Key Fob begins to operate normally.
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005119This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005061This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11003654Phone call sound quality may be adjusted to fit the Tacoma owners preferences.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003619Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
- 11003607Some customers have complained that the wireless functions of their Key Fob stop working. Key Fob LEDs will not turn ON, but engine starts with key held up against start button. Key battery voltage is confirmed OK and no DTC/RoB is found. This condition may occur if customer places Key Fob near wireless charger while phone is charging. When the key battery is removed and reinstalled, the Key Fob begins to operate normally.
- 11003599Phone call sound quality may be adjusted to fit the Tacoma owners preferences.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003564Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
- 11003552Some customers have complained that the wireless functions of their Key Fob stop working. Key Fob LEDs will not turn ON, but engine starts with key held up against start button. Key battery voltage is confirmed OK and no DTC/RoB is found. This condition may occur if customer places Key Fob near wireless charger while phone is charging. When the key battery is removed and reinstalled, the Key Fob begins to operate normally.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10247828TSB: All 2020 ? 2023 model year 4Runner, 2018 ? 2022 model year Sequoia, 2018 ? 2023 model year Tacoma, and 2018 ? 2021 model year Tundra vehicles are equipped with Pre-collision System (PCS) and Dynamic Radar Cruise Control (DRCC) as part of the Toyota Safety Sense (TSS) package. The PCS and DRCC systems are designed to help mitigate a potential collision and maintain a pre-determined traveling distance. It is recommended to disable the PCS and DRCC systems on vehicles that have been modified (ride height, oversized wheels/tires, brush bars, etc.) in a way that potentially disrupts the functionality of these systems. Vehicle owner?s written consent is required before performing the calibration to permanently disable the PCS and DRCC systems. Follow the Repair Procedure in this bulletin to disable the PCS and DRCC systems.
- 10244113TSB: Replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) (see Figure 1) for most 1979 ? 2023 model year vehicles may be available provided the requests meet the criteria listed in this Service Bulletin. Follow the Procurement Procedure in this bulletin to request a replacement certification label or VIN plate.
- 10244111TT: A very small percentage of customers experience operational difficulties with some telematics features which they cannot resolve on their own. These resources, in conjunction with the Repair Manual, are for dealership personnel to assist those customers with user issues, user errors, and compatibility issues with other vehicle systems and external applications encountered while operating telematics features. Toyota has developed and provided the following Telematics Diagnostic Guide to assist dealer technicians.
- 10244108TSB: Some 2005 ? 2023 model year Tacoma vehicles equipped with a manual transmission may exhibit a squeak or creak noise from the clutch pedal when it is depressed or released.
- 10241402TSB: Some 2019 ? 2023 model year Tacoma Double Cab vehicles may exhibit a whine noise from the rear of the vehicle. This condition may occur while driving around 50 mph (80 kph) at constant speed, slight acceleration, or slight deceleration. This condition may be caused by rear differential vibration transferring through the chassis and body
- 10241387TSB: Some 2023 ? 2024 model year Toyota vehicles use hub bolts in place of studs/nuts to fasten the wheels to the vehicle. If non-compatible wheels or hub bolts/nuts are installed, there is increased risk that the wheel(s) could come off resulting in a crash. This service bulletin outlines the physical differences and precautions that should be taken when servicing different wheel and wheel fastener types.
- 10238157TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system.
- 10238130This Toyota Genuine Power Port provides additional capability to your phone or tablet, so your devices always have power/charge. Includes two fast charging smart USB connectors with blue LED power status light. Applicable to MY21, MY22, and 2023 Tacoma
- 10235239TT: Some 2020-2023 Manual Transmission Tacoma vehicles may exhibit an abnormal clutch pedal creak/squeak sound during operation.
- 10234341TSB: Some 2016 ? 2023 model year Tacoma vehicles may exhibit a condition where snow or ice builds up between the right or left front door and front fender, preventing the front door from fully opening. Follow the Repair Procedure in this bulletin to address this condition.
- 10234332TT: Electronic Parts Catalog (EPC) does not include notes requiring ordering the Protector Heater seals when replacing the air conditioning Evaporator Core (88511- #####) or Radiator Heater Unit SubAssembly (87107- #####
- 10234312TT: Electronic Parts Catalog (EPC) does not include notes requiring ordering the Protector Heater seals when replacing the air conditioning Evaporator Core (87511- #####) or Radiator Heater Unit Sub-Assembly (87107- #####).
Every Toyota Tacoma model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.