2016 Toyota Tacoma
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Toyota › Tacoma › 2016
These records cover every 2016 Toyota Tacoma. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
4 recalls name the 2016 Toyota Tacoma. Newest first.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2011-2016 Toyota Tacoma and 4Runner vehicles equipped with accessory hood scoops installed by SET or SET dealers. The adhesive attaching the hood scoop may weaken, allowing the hood scoop to detach from the vehicle.
Risk and remedy
Risk
If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.
Remedy
SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016-2017 Tacoma vehicles equipped with a six-cylinder engine. The affected vehicles have a crank position sensor that may malfunction, potentially resulting in an engine stall.
Risk and remedy
Risk
An engine stall may increase the risk of a crash.
Remedy
Toyota will notify owners, and dealers will replace the crank position sensor with an improved design, free of charge. The recall began July 26, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is H0H.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2016-2017 Tacoma vehicles. Oil may leak from the area where the rear differential carrier is assembled to rear axle housing.
Risk and remedy
Risk
If the vehicle is operated with an insufficient amount of oil in the rear differential, the differential may seize and cause a loss of control, increasing the risk of a crash.
Remedy
Toyota will notify owners, and dealers will inspect the rear differential for oil leakage. Based on the inspection, dealers will either tightening the fastening nuts or replace the fastening nuts and gasket. If the rear differential components are damaged, the rear differential carrier assembly will be replaced. The repairs will be performed free of charge. The recall June 19, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is H0G.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2016 Tacoma trucks manufactured August 20, 2015, to September 10, 2015. In the affected vehicles, incorrect bolts were used to install the driver's knee air bag module.
Risk and remedy
Risk
The incorrect bolts may loosen over time and affect the performance of the driver's knee air bag, increasing the risk of driver injury during a crash that necessitates deployment of the air bags.
Remedy
Toyota will notify owners, and dealers will install the correct driver's knee air bag module mounting bolts, free of charge. The recall began on November 19, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is F0T.
Owner complaints
324 complaints4 involved a crash4 involved a fire1 injuries
What owners report most
Latest complaints
- Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2016 Toyota Tacoma. It was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 132,000 and at the time of registration, it was discovered that the mileage was 229,000.
- Structure › Body
Toyota has a paint problem on the tacomas. The paint is the bright white, .040 . They have painted all 4 doors,both front fenders and the pillars on each side of the windshield. I’m having the same problem on my hood,top of windshield and bed . Toyota refuses to take responsibility for these areas.…
Toyota has a paint problem on the tacomas. The paint is the bright white, .040 . They have painted all 4 doors,both front fenders and the pillars on each side of the windshield. I’m having the same problem on my hood,top of windshield and bed . Toyota refuses to take responsibility for these areas. They call this a customer satisfaction program instead of a recall so they don’t have to paint the whole truck. I have a 25 year old truck that has better paint than it. I just wanted to let you know about this situation. Thanks [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Power train
The contact owns a 2024 Ford Edge. The contact stated that the vehicle was shaking while driving. The contact noticed there was fluid emerging from the rear of the vehicle near the tire. There were no warning lights illuminated. The vehicle was taken to the local dealer, who confirmed there was no…
The contact owns a 2024 Ford Edge. The contact stated that the vehicle was shaking while driving. The contact noticed there was fluid emerging from the rear of the vehicle near the tire. There were no warning lights illuminated. The vehicle was taken to the local dealer, who confirmed there was no recall or leak. The vehicle was not repaired. The manufacturer was contacted, who referred to the local dealer. The failure mileage was approximately 100,000.
- Fuel/propulsion system
The original low pressure fuel pump failed at 114,700 miles. The symptoms of the failure were loss of power on the freeway, quickly followed by the engine stumbling, then shutting off completely forcing me to change lanes without power. The vehicles has had to be towed on 2 occasions because of…
The original low pressure fuel pump failed at 114,700 miles. The symptoms of the failure were loss of power on the freeway, quickly followed by the engine stumbling, then shutting off completely forcing me to change lanes without power. The vehicles has had to be towed on 2 occasions because of this. The pump was replaced at 114,700 miles by a Toyota dealer at my own cost (no warranty, no recall). Now only 20k miles later the fuel pump has failed again. This issue has put my family at serious risk of accident to complete engine shut off at highway speeds. Now that I am on my third low pressure fuel pump, I have little confidence that this is being addressed by the pump manuf. and Toyota.
- Seat belts · Seats · Unknown or other
Dear Toyota Japan Customer Experience Team, I am the owner of a 2016 Toyota Tacoma currently registered in Guam, U.S.A. I am writing to request your assistance regarding a water leak issue from the rear brake light area, which has caused the carpets and seats to become wet and develop mold. I…
Dear Toyota Japan Customer Experience Team, I am the owner of a 2016 Toyota Tacoma currently registered in Guam, U.S.A. I am writing to request your assistance regarding a water leak issue from the rear brake light area, which has caused the carpets and seats to become wet and develop mold. I originally purchased this vehicle in Saipan and recently relocated to Guam. When I visited the Guam Toyota Service Center, they kindly inspected my vehicle and informed me that this issue is related to the 3rd brake light gasket recall; however, the recall period has already expired. Unfortunately, I was never notified of this recall while the vehicle was in Saipan. Continuous exposure to mold has seriously affected both my health and my daughter’s health. Because of this, I had the vehicle professionally cleaned and sanitized by a specialist company. The Tacoma has always been our family’s favorite car, but now I drive it only because I have no choice. Every time I get in, I feel anxious and uneasy. The water leak itself is concerning, but the mold issue worries me even more. I truly hope this water leak and the mold problem can both be resolved so that I can once again enjoy driving my Tacoma with peace of mind. The blue circles in the attached photos indicate areas suspected of mold. These photos were taken right before I sent the car for cleaning. According to the cleaning company, when they removed the seats, they found water underneath the seats and carpets. Whenever I drive the vehicle, I experience persistent coughing and headaches due to mold exposure. This has become a serious health and safety concern. Since this issue is directly related to a previously recalled safety defect, I kindly request Toyota Japan to consider a Goodwill Repair or Safety Exception to address the water leak and the resulting interior damage.
- Structure › Body
Severe clear coat and paint fading on hood, roof and sides of truck.
- Power train
2016 Toyota Tacoma is known to have an issue with the timing cover leaking oil. This is a Fire Hazard: Oil leaking onto hot engine components can vaporize and ignite, posing a fire risk to the vehicle and surrounding areas and can cause environmental pollution.
- Latches/locks/linkages › Electronic lock/latch actuator
The rear passenger door lock actuator on my 2016 Toyota Tacoma failed prematurely, causing the door to no longer lock or unlock properly. The failure required replacement of the entire actuator assembly at a Toyota dealership at a cost of $727.19. This failure occurred without abuse or unusual use…
The rear passenger door lock actuator on my 2016 Toyota Tacoma failed prematurely, causing the door to no longer lock or unlock properly. The failure required replacement of the entire actuator assembly at a Toyota dealership at a cost of $727.19. This failure occurred without abuse or unusual use and is not consistent with normal wear and tear. I am aware of numerous similar complaints and pending class action lawsuits involving door lock actuator failures across multiple Toyota models, indicating this is a known and recurring defect. A door that cannot reliably lock or unlock presents a safety and security concern, particularly for passengers and children, and increases the risk of unauthorized entry or inability to exit the vehicle in an emergency.
- Structure › Body
2016 Toyota Tacoma – severe clear coat and paint failure on the hood and roof. The clear coat began peeling in 2022 and has progressively worsened. Large sections of the hood and roof show complete delamination, oxidation, and exposed basecoat. This is a widely reported defect for 2015–2017…
2016 Toyota Tacoma – severe clear coat and paint failure on the hood and roof. The clear coat began peeling in 2022 and has progressively worsened. Large sections of the hood and roof show complete delamination, oxidation, and exposed basecoat. This is a widely reported defect for 2015–2017 Tacomas across multiple paint colors. Toyota Customer Care confirmed today that my VIN is not included in Customer Support Program 23TE08 and that no goodwill repair would be authorized, even though the defect is identical to the vehicles Toyota acknowledges as affected. This appears to be a manufacturing defect that compromises durability and corrosion resistance. Photos and documentation are available upon request.
- Structure › Body
Paint on hood and roof is fading significantly.
- Unknown or other
The seat heater pins have melted, leaving black residue. thus showing possibilities of a fire
- Structure
The contact owns a 2016 Toyota Tacoma. The contact stated that while driving, there was a musty odor coming from the interior of the vehicle. The contact was unable to locate the source of the odor. The contact stated that on a separate occasion, while vacuuming the vehicle, the contact noticed…
The contact owns a 2016 Toyota Tacoma. The contact stated that while driving, there was a musty odor coming from the interior of the vehicle. The contact was unable to locate the source of the odor. The contact stated that on a separate occasion, while vacuuming the vehicle, the contact noticed that the carpet and floor mats from the rear passenger’s side were wet. The vehicle was taken to the dealer, where it was diagnosed and determined that the rear quarter duct vents had fractured, and water was entering the interior of the vehicle. The vehicle was not repaired due to the cost. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 80,000.
- Engine
Bought 2016 Tacoma in 2022 w/ 53k miles. Hit 58,850 (ish) and had an noticable oil leak… apparently this was a “Well Known” issue, as the mechanic @ Surprise, AZ Dealership (Toyota of Surprise, 13543 N. Auto Show Ave., Surprise, AZ 85388) told my wife and I…. it’s from this same thing that google…
Bought 2016 Tacoma in 2022 w/ 53k miles. Hit 58,850 (ish) and had an noticable oil leak… apparently this was a “Well Known” issue, as the mechanic @ Surprise, AZ Dealership (Toyota of Surprise, 13543 N. Auto Show Ave., Surprise, AZ 85388) told my wife and I…. it’s from this same thing that google showed me also: “Engine oil leaks: Reports on Consumer Reports and other forums detail expensive repairs to fix oil leaks from the front seal or timing cover, which can cost $5,000 or more because the engine often needs to be removed for the repair.” And this was 100% my case- and confirmed by the Toyota Dealers Mechanic verbally. Leaks were without engine light indicators “at all”. The dealership added a dye, told me to drive 100-500 miles and return to have a re-inspection done after their initial one came with no results. Initially I spotted this while I was conducting a regular 3,000 mile oil change. (2nd oil change since owning the truck. So my out of pocket was around $5,700+, for an apparent (see attached) “well-known” Dealer issue. @ 60k, a major repair cost for this should NOT but coming from the consumer, and needs to be listed as a “recall”. Had I not noticed the missing oil, this could have left me stranded, my family stranded, or caused many other traveling issues throughout my driving experiences. I repaired this around two years ago, but have been terrified to drive my truck! I’ve driven about 1,000 miles or less since the repair (in 2 years time). I’m selling first chance I can, BUT, I WANT MY MONEY BACK! I have the receipt in a safe for when this becomes a recall - to prove i paid it, and to get a FULL REFUND!!! That is not how good business is done by Toyota. I owned a 2004 and 2005 Camrys prior, as well as a 2014 Lexus GS 350 F Sport (all in my name), this truck was a dream, now a nightmare. Please, for everyone complaining online and those that have had to also pay for these repairs @ low mileage, MAKE THIS INTO A RECALL FOR 2016 TACOMAs.
- Electrical system
I am reporting a persistent and unsafe issue with the factory-installed Entune infotainment system in my 2016 Toyota Tacoma. While driving — whether locally or on the highway — the system frequently freezes, becomes unresponsive, or abruptly resets itself, often multiple times per drive. This…
I am reporting a persistent and unsafe issue with the factory-installed Entune infotainment system in my 2016 Toyota Tacoma. While driving — whether locally or on the highway — the system frequently freezes, becomes unresponsive, or abruptly resets itself, often multiple times per drive. This directly affects my ability to safely use the navigation, backup camera, and audio controls while in motion. The system’s crashes divert my attention from the road, especially when I’m relying on navigation and it either stops functioning or forces me to interact with the screen to regain control. These interruptions increase the risk of distracted driving and could easily contribute to an accident. I have attempted to install the software update provided on Toyota’s official website, but the update is older than the version already installed on my vehicle (0101A0), so the system blocks the update. There is no way for a consumer to reinstall or flash the current version, and any potential resolution is only available at a dealership for a fee, effectively putting the fix behind a paywall. Toyota has not issued a recall or service bulletin for this issue, despite dozens of reports from other owners on Tacoma and Prius forums describing the same crash behavior and software version conflicts. This is a significant safety concern, especially when the infotainment system is used for navigation during high-speed or complex driving conditions. The inability to maintain consistent functionality puts drivers and others on the road at risk. I am requesting that NHTSA investigate this widespread issue and press Toyota to issue a free repair or software patch for all affected vehicles. Symptoms: •Frequent infotainment restarts while driving •Frozen or unresponsive touchscreen •Glitched navigation system and lost GPS routing •Driver distraction due to repeated system failure
- Engine
I have experienced two major failures on my 2016 Toyota Tacoma TRD Sport with less than 90,000 miles: a leaking coolant crossover pipe, which required partial engine disassembly and cost me approximately $2,500, and a leaking timing chain cover, which required a full front-end teardown and cost…
I have experienced two major failures on my 2016 Toyota Tacoma TRD Sport with less than 90,000 miles: a leaking coolant crossover pipe, which required partial engine disassembly and cost me approximately $2,500, and a leaking timing chain cover, which required a full front-end teardown and cost over $4,500. Both issues are known problems across 2016+ Tacoma models with the 3.5L V6 (2GR-FKS engine), yet Toyota has not issued a recall or warranty enhancement. These failures present safety risks related to overheating and oil loss and result in significant financial burden to owners. Toyota needs to be held accountable for these premature, design-related failures.
- Steering
During a safety inspection, it was found out that the steering rack was leaking. In a quick research on Google, it appears that many people that own this particular year and tacomas are experiencing the same issue. It is the first time for any car that we own and we keep our cars for more than 10…
During a safety inspection, it was found out that the steering rack was leaking. In a quick research on Google, it appears that many people that own this particular year and tacomas are experiencing the same issue. It is the first time for any car that we own and we keep our cars for more than 10 years. To us, this could be a manufacturing defect that should be investigated and a recall issue. We had it fixed so it can pass inspection, but something just doesn't make sense.
- Suspension
When using four-wheel drive, the vehicle was unable to make a left turn. I disengaged four-wheel drive, and the vehicle was stuck in four-wheel drive. This happened on two occasions. The first time was approximately August 2022 and the second time was last year. When I took it to the dealership…
When using four-wheel drive, the vehicle was unable to make a left turn. I disengaged four-wheel drive, and the vehicle was stuck in four-wheel drive. This happened on two occasions. The first time was approximately August 2022 and the second time was last year. When I took it to the dealership, they said here was nothing wrong with it and they told me that I probably used the four-wheel drive incorrectly. Luckily, I was able to get the truck into a parking lot. The way that I was able to disengage it was to put the truck into reverse and back up a few yards then go forward a few yards and repeat until I hear a loud thump.
- Seats
Heated seat had stopped working, checked and found the problem. The module that controls the heated seats had a melted connector and wires, causing the seat to no longer be able to have heated seats.
- Engine
Upper Intake manifold flap actuator ( part: Toyota 17190-0P101 ) brakes in the intake resulting in wrong air reading and forcing vehicle into limp mode causing the vehicle to rapidly decrease speed, and creating a potential accident with other vehicles and semi's. this will continue to happen but…
Upper Intake manifold flap actuator ( part: Toyota 17190-0P101 ) brakes in the intake resulting in wrong air reading and forcing vehicle into limp mode causing the vehicle to rapidly decrease speed, and creating a potential accident with other vehicles and semi's. this will continue to happen but this will give a person a false sense of security since error codes will reset once vehicle is turned off and on, a reassurance to a person that the issue has resolved itself since this will only happen at high speeds. the part is designed for fuel efficiency, as the flap opens and closes air is controlled properly for emission, but once broken will throw error codes, and force vehicle into limp mode this part is not be repairable, the part needs to be changed completely. this would happen to me while accelerating on highways, up mountain passes and pushing vehicle over 4000 rpm.
- Engine
Rear Coolant Bypass Joint leak. Coolant leaking through this pipe and accumulating.
- Unknown or other
Paint is chipping off in several places and have read this is a major problem with tacomas in the white color
- Engine
Coolant leaking
- Structure › Body
The paint on my 2016 Toyota Tacoma is failing after a few years of owning the truck, it has been well maintained and washed but the problem keeps getting worse. I have searched online and it seems to be an issue with white and magnetic grey colored Toyota cars but no recall on magnetic grey paint.
- Electrical system · Seats
Seat heating module for my driver seat has melted and is further irrepairable without buying the entire harness to fix the issue. There are multiple reports of this happening across forums.
- Unknown or other
I have recently been made aware of the Super White paint recall and know that is not yet in full force or able to be serviced at this time. That being said, it appears that the recall only covers " paint peeling along the exterior door window frames and front inner fenders under the hood on certain…
I have recently been made aware of the Super White paint recall and know that is not yet in full force or able to be serviced at this time. That being said, it appears that the recall only covers " paint peeling along the exterior door window frames and front inner fenders under the hood on certain Tacoma vehicles with 040 Super White paint color", But there are multiple reports of this entire paint job being defective over multiple generations as well as paint outside of these areas specified. This recall should cover an entire repaint and is extremely frail in quality otherwise.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Electrical overstress
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air…
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010353Some 2016 2022 model year Tacoma vehicles with Super White (040) paint may exhibit paint peeling along the exterior window door frames and/or inner fender edges under the hood. The affected panel(s) require repainting to address this condition. The paint repair may need to be sublet to a body shop.
- 11010328Technical instructions for customer support program 23te08 coverage for paint peeling on door frames + front inner fenders certain 2016-2022 model year tacoma
- 11010327Customer Support Program 23TE08 Paint Repair Process Updated 10.02.2024 Updated Parts quantity on two parts.
- 11010083Technical instructions for customer support program 23te08 coverage for paint peeling on door frames + front inner fenders certain 2016-2022 model year tacoma
- 11010082In our continuing efforts to ensure the best in customer satisfaction, Toyota is announcing a Customer Support Program to provide coverage for paint peeling on door frames and front inner fenders on certain 2016-2022 model year Tacoma vehicles. Toyota has received some reports of paint peeling along the exterior door window frames and front inner fenders under the hood on certain Tacoma vehicles with 040 Super White paint color. Although the vehicle paint is covered by Toyotas New Vehicle Limited Warranty for three years, or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 11010081Customer Support Program 23TE08 Paint Repair Process
- 11010080Toyota has received some reports of paint peeling along the exterior door window frames and front inner fenders under the hood on certain Tacoma vehicles with 040 Super White paint color. Although the vehicle paint is covered by Toyotas New Vehicle Limited Warranty for three years, or 36,000 miles (whichever comes first), we at Toyota care about the customers ownership experience. Toyota is providing coverage for repairs related to the condition described above.
- 11010066Customer support program frequently asked questions
- 11007455Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11007449Customer renotificaions for 21TD03, 22LD01, 22LD02
- 11007448The Center High-Mounted Stop Lamp on the involved vehicles has a seal between the lamp and the vehicle body which can deteriorate over time. If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.
- 11007445The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11007444To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11007443Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11006161Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines. This Service Bulletin is to provide a general overview and direction for the odor remediation process.
- 11006155Customer renotificaions for 21TD03, 22LD01, 22LD02
- 11006154The Center High-Mounted Stop Lamp on the involved vehicles has a seal between the lamp and the vehicle body which can deteriorate over time. If the seal deteriorates sufficiently, water from outside the vehicle could leak into the vehicle cabin through the seal.
- 11006151The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11006150To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
- 11006149Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11005153Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination.
- 11005149Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid.
- 11005122Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005119This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11005064Some 2005 2024 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
- 11005061This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for some 2008 2025 model year Toyota vehicles.
- 11003649The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003647To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003644Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003619Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
- 11003594The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. While Toyota paint quality, durability, and resistance to environmental factors is continuously being improved, it remains the responsibility of the dealer to protect and maintain the vehicles paint finish from the time of arrival at the dealership until retail delivery to the customer. In areas known for high frequency and/or concentration of acid rain (see Figure 1), frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
- 11003592To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible. SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. PD017-04. The entire bulletin has been updated.
- 11003589Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: Minor damage: requires only buffing to repair. Moderate damage: usually requires neutralizing, color sanding, and buffing. Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to the first sale. To read, While the quality and durability of paint on Toyota vehicles is continuously being improved, it remains the dealers responsibility to protect and maintain the quality of the vehicles paint finish after receipt at the dealership prior to first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
- 11003564Customers have expressed concerns about the performance of Qi Wireless Chargers. Wireless chargers on applicable vehicles are designed to work with Qi Certified devices only. MagSafe devices, that are not Qi Certified, may not charge as expected with Qi Wireless Chargers.
- 10253223This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
- 10251757Ti: K0D expired on 10/31/2023. Technical instructions for limited service campaign K0D frame corrosion resistant compound (crc) application certain 2016 ? 2017 model year tacoma
- 10251756K0D expired on 10/31/2023.
- 10251755DP: K0D expired on 10/31/2023. Toyota has received reports regarding frame corrosion perforation on 2011 ? 2017 model year Tacoma vehicles. In these reports, customers have indicated that vehicles operated in specific cold climate areas with high road salt usage may exhibit more-than-normal corrosion to the vehicle?s frame. This condition is unrelated to and separate from normal surface rust which is commonly found on metallic surfaces after some years of usage and/or exposure to the environment.
- 10251742Ti: K0D expired on 10/31/2023. Technical instructions for limited service campaign K0D frame corrosion resistant compound (crc) application certain 2011 ? 2015 model year tacoma
- 10251070OBSOLETE NOTICE January 22, 2024: This bulletin is now obsolete. Please see T-SB-0057-18.
Every Toyota Tacoma model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.